Please wait a minute...
《材料导报》期刊社  2018, Vol. 32 Issue (8): 1328-1332    https://doi.org/10.11896/j.issn.1005-023X.2018.08.023
  材料研究 |
成层式铝蜂窝夹芯结构冲击响应试验研究
罗伟铭, 石少卿, 廖瑜, 孙建虎
陆军勤务学院军事设施系,重庆 401331
An Experimental Investigation upon the Impact Response of the Layered Aluminum Honeycomb Sandwich Structure
LUO Weiming, SHI Shaoqing, LIAO Yu, SUN Jianhu
Department of Military Installations, Army Logistics University of PLA, Chongqing 401331
下载:  全 文 ( PDF ) ( 1844KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 以牺牲层设计为背景,提出一种成层式铝蜂窝夹芯结构。通过两种能级的落锤冲击试验,得到不同组合试件的局部冲击响应结果。根据能量吸收、荷载峰值、冲头位移和背板挠度的对比分析,得出以下结论:结构在相对较低能级(17~83 J)的冲击作用下,除了永久塑性变形,也伴随着一定的弹性变形;同时,在芯层质量相同的前提下,可优先选择胞元较小、高度较低的蜂窝作为单层结构的芯层;全贯穿临界值应当介于83~119 J之间,在设计牺牲层时,局部冲击的极限能量设计值应当低于该临界值;芯层的相对密度对抗局部冲击性能的影响较为明显;根据牺牲层的设计标准,在本文的局部冲击试验研究范围内,AB、BA、ABA型结构在综合指标上具有相对优势。研究结果可为成层式铝蜂窝夹芯结构在防护工程中的应用提供参考。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
罗伟铭
石少卿
廖瑜
孙建虎
关键词:  铝蜂窝  成层式  吸能  冲击    
Abstract: The present work proposed a type of layered aluminum honeycomb sandwich structure from the perspective of sacrificial cladding designing. By drop weight impact test, the responses of the specimens with different combinations were obtained under two energy level impact. By comparing the energy absorption, peak value of impact load, displacement of impactor, deflection of specimens, some conclusions were drawn as follows: there was permanent plastic deformation accompanied by a certain degree of elasticity deformation in the structures under lower energy level (17—83 J) impact. On the premise of the same quality, the honeycomb with smaller size and smaller height should be given priority as the core of the sandwich structures. The critical value should be between 83—119 J. In the design of sacrificial cladding, the limit energy design value of local impact should be lower than the critical value; the relative density of core layer significantly influences the local impact resistance of the structure; according to the design criterion of sacrificial cladding, within the research scope of this paper, type AB, BA and ABA structures have comparative advantage according to the aggregative indicators. The results provide helpful reference for practical application of the layered aluminum honeycomb sandwich structure in protective engineering.
Key words:  aluminum honeycomb    layered    energy absorption    impact
               出版日期:  2018-04-25      发布日期:  2018-05-11
ZTFLH:  O347.3  
基金资助: 国家自然科学基金(51378495;51408602)
作者简介:  罗伟铭:男,1988年生,博士研究生,主要研究方向为结构工程 E-mail:lwmofficial@163.com
引用本文:    
罗伟铭, 石少卿, 廖瑜, 孙建虎. 成层式铝蜂窝夹芯结构冲击响应试验研究[J]. 《材料导报》期刊社, 2018, 32(8): 1328-1332.
LUO Weiming, SHI Shaoqing, LIAO Yu, SUN Jianhu. An Experimental Investigation upon the Impact Response of the Layered Aluminum Honeycomb Sandwich Structure. Materials Reports, 2018, 32(8): 1328-1332.
链接本文:  
http://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2018.08.023  或          http://www.mater-rep.com/CN/Y2018/V32/I8/1328
1 Wu Tingyang, Wu Jinwu. Sound insulation property of honeycomb sandwich panels[J].Materials Review B:Research Papers,2016,30(4):153(in Chinese).
吴廷洋,吴锦武.蜂窝层合板结构的隔声特性研究[J].材料导报:研究篇,2016,30(4):153.
2 Wang Chenhui, Gu Xinling, Chen Yu, et al. Study on absorbing properties of aluminum honeycomb-wood based composite materials[J].Materials Review B:Research Papers,2015,29(4):146(in Chinese).
王晨辉,顾新玲,陈羽,等.蜂窝铝-木基复合材料电磁波吸收特性研究[J].材料导报:研究篇,2015,29(4):146.
3 Ding Yuanyuan, Wang Shilong, Zheng Zhijun, et al. Anti-blast analysis of cellular sacrificial cladding[J].Journal of Explosion and Shock Waves,2017,46(3):825(in Chinese).
丁圆圆,王士龙,郑志军,等.多胞牺牲层的抗爆炸分析[J].爆炸与冲击,2017,46(3):825.
4 Aleyaasin M, Harrigan J J, Reid S R. Air-blast response of cellular material with a face plate: An analytical-numerical approach[J].International Journal of Mechanical Sciences,2015,91(47):64.
5 Langdon G S, Karagiozova D, Theobald M D, et al. Fracture of aluminium foam core sacrificial cladding subjected to air-blast loading[J].International Journal of Impact Engineering,2010,37(6):638.
6 Palanivelu S, Paepegem W V, Degrieck J, et al. Close-range blast loading on empty recyclable metal beverage cans for use in sacrificial cladding structure[J].Engineering Structures,2011,33(6):1966.
7 Guruprasad S, Mukherjee A. Layered sacrificial claddings under blast loading Part Ⅰ—Analytical studies[J].International Journal of Impact Engineering,2000,24(9):957.
8 Guruprasad S, Mukherjee A. Layered sacrificial claddings under blast loading Part Ⅱ—Experimental studies[J].International Journal of Impact Engineering,2000,24(9):975.
9 Lin Yuliang, Zhang Zhifeng, Chen Rong, et al. Cushioning and energy absorbing property of combined aluminum honeycomb[J].Advanced Engineering Materials,2015,17(10):1434.
10 Lei Cao, Lin Yuliang, Lu Fangyun, et al. Experimental study on the shock absorption performance of combined aluminium honeycombs under impact loading[J].Shock and Vibration,2015,2015:1.
11 Luo Weiming, Shi Shaoqing, Chen Zipeng, et al. Influence of layer configuration on the energy absorption of layered aluminum honeycomb[J].Materials Review B:Research Papers,2017,31(7):82(in Chinese).
罗伟铭,石少卿,陈自鹏,等.层间配置对成层式铝蜂窝吸能特性的影响[J].材料导报:研究篇,2017,31(7):82.
12 Fu Minghui, Xu Outeng, Chen Yu. An overview of equivalent parameters of honeycomb cores[J].Materials Review A:Review Papers,2015,29(3):127(in Chinese).
富明慧,徐欧腾,陈誉.蜂窝芯层等效参数研究综述[J].材料导报:综述篇,2015,29(3):127.
13 Wang Chuang, Liu Rongqiang, Deng Zongquan, et al. Experimental and numerical studies on aluminum honeycomb structure with va-rious cell specifications under impact loading[J].Journal of Vibration and Shock,2008,27(11):56(in Chinese).
王闯,刘荣强,邓宗全,等.铝蜂窝结构的冲击动力学性能的试验及数值研究[J].振动与冲击,2008,27(11):56.
[1] 张景卫, 李地红, 高群, 于海洋, 代函函. 橡胶形态及分布对水泥制品抗冲击能力的影响[J]. 材料导报, 2019, 33(z1): 261-263.
[2] 李景文, 乔建刚, 付旭, 刘晓立. 岩土锚固吸能锚杆支护材料/结构及其力学性能研究进展[J]. 材料导报, 2019, 33(9): 1567-1574.
[3] 周昱程, 刘娟红, 纪洪广, 付士峰, 谷峪. 温度-复合盐耦合条件下纤维混凝土井壁冲击倾向性试验研究[J]. 材料导报, 2019, 33(16): 2671-2676.
[4] 胡俊, 任建伟, 马巍, 刘建华, 王爱国. 冲击荷载下含随机缺陷的梯度蜂窝材料的力学性能[J]. 材料导报, 2019, 33(16): 2777-2784.
[5] 巴奇楠, 宋仁伯, 冯一帆, 李论. 表面爆炸处理后的ZGMn13Cr2钢的冲击磨损性能及硬化机理[J]. 材料导报, 2019, 33(10): 1712-1716.
[6] 张建斌, 刘帆, 薛飞. 热处理工艺对P91耐热钢中δ-铁素体和冲击性能的影响[J]. 《材料导报》期刊社, 2018, 32(8): 1318-1322.
[7] 戎翔, 邓安仲, 李飞, 李丰恺. 柱胞夹芯复合材料设计加工及吸能性能研究现状[J]. 《材料导报》期刊社, 2018, 32(5): 822-827.
[8] 张忠科, 张剑飞, 于洋, 王希靖. 厚板铝合金搅拌摩擦焊接头的冲击性能[J]. 材料导报, 2018, 32(22): 3936-3940.
[9] 傅定发,冷宇,高文理. 微合金元素Nb对低碳铸钢强度和冲击韧性的影响[J]. 《材料导报》期刊社, 2018, 32(2): 237-242.
[10] 刘小可, 俞科静, 钱坤. 剪切增稠胶/聚氨酯泡沫复合材料的制备与力学性能[J]. 材料导报, 2018, 32(18): 3255-3260.
[11] 贾翠玲, 陈芙蓉. 超声冲击处理对铝合金焊接应力的影响[J]. 材料导报, 2018, 32(16): 2816-2821.
[12] 吴晓露, 李迎春, 武海花, 孔宇飞. PMDA对废旧HIPS的修复作用[J]. 《材料导报》期刊社, 2018, 32(14): 2508-2512.
[13] 唐昌平, 左国良, 刘文辉, 朱美韵, 李志云, 李权, 刘筱, 卢立伟. 挤压-T5态Mg-8Gd-4Y-Nd-Zr合金的动态冲击行为[J]. 《材料导报》期刊社, 2018, 32(14): 2437-2441.
[14] 何柏林,金辉,张枝森,谢学涛,丁江灏. SMA490BW钢对接接头高周疲劳性能的机理探究[J]. 《材料导报》期刊社, 2018, 32(12): 2008-2014.
[15] 秦建彬,张广成,史学涛. 剪切增稠液及其复合材料*[J]. 《材料导报》期刊社, 2017, 31(7): 59-64.
[1] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6] XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg98.5Zn0.5Y1 Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7] ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed