Please wait a minute...
材料导报  2020, Vol. 34 Issue (18): 18081-18085    https://doi.org/10.11896/cldb.19090097
  金属与金属基复合材料 |
喷丸对TC4合金微弧氧化涂层磨损和腐蚀行为的影响
任超1,2, 罗军明1,2, 陈宇海3, 黄俊1,2, 徐吉林1,2
1 南昌航空大学材料科学与工程学院,南昌 330063
2 江西省航空材料表面技术工程研究中心,南昌 330063
3 航空工业成都飞机工业(集团) 有限责任公司,成都 610092
Effect of Shot Peening on Wear and Corrosion Behavior of Micro-arc Oxidation Coating of TC4 Alloy
REN Chao1,2, LUO Junming1,2, CHEN Yuhai3, HUANG Jun1,2, XU Jilin1,2
1 School of Materials Science and Engineering, Nanchang University of Aeronautics, Nanchang 330063, China
2 Jiangxi Provincial Engineering Research Center for Surface Technology of Aeronautical Materials, Nanchang Hangkong University, Nanchang 330063, China
3 Chengdu Aircraft Industry (Group) Co.,Ltd., Chengdu 610092, China
下载:  全 文 ( PDF ) ( 3955KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 对TC4钛合金表面进行喷丸(SP)预处理制备出表层纳米结构膜层,采用微弧氧化(MAO)恒电压控制模式在NaH2PO4和Na2SiO3组成的电解液中制得陶瓷层,获得SP/MAO复合涂层。研究了喷丸时间对SP/MAO复合涂层组织结构及耐磨、耐蚀性能的影响。结果表明:经过喷丸处理后,随着喷丸时间的延长,TC4合金表层晶粒尺寸减小,微观应变和表面粗糙度逐步增大。经喷丸30 min预处理的SP/MAO复合涂层的摩擦系数最小,磨损率较MAO涂层降低了71.3%。随着喷丸时间的延长,SP/MAO复合涂层自腐蚀电位呈先增加后降低的趋势,腐蚀电流密度呈先降低后增加的趋势,喷丸30 min时,SP/MAO涂层的耐蚀性最好。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
任超
罗军明
陈宇海
黄俊
徐吉林
关键词:  TC4钛合金  喷丸  微弧氧化  耐磨性  耐蚀性    
Abstract: The surface nanostructured film was prepared by shot peening (SP) on the surface of TC4 alloy.The ceramic layer was prepared in the electrolyte composed of NaH2PO4 and Na2SiO3 by micro-arc oxidation (MAO) constant voltage control mode, and the SP/MAO composite surface modified layer was obtained. The effects of shot peening on the microstructure, wear resistance and corrosion resistance of SP/MAO composite coatings were investigated. The results show that after shot peening, with the prolongation of shot peening time, the surface grain size of TC4 alloy decreases, while the microscopic strain and surface roughness increase gradually.The SP/MAO composite coating pretreated by shot peening for 30 min had the lowest friction coefficient and the wear rate was 71.3% lower than that of the micro-arc oxidation coating. With the prolongation of shot peening time,the corrosion potential of SP/MAO composite coating increased first and then decreased, and the corrosion current density decreased first and then increased. The SP/MAO coating had the best corrosion resistance when shot peening for 30 min.
Key words:  TC4 alloy    shot peening    micro-arc oxidation    wear resistance    corrosion resistance
                    发布日期:  2020-09-12
ZTFLH:  TG146.2  
基金资助: 国家自然科学基金(51764041);江西省自然科学基金(20161BAB216099)
通讯作者:  ljmniat@126.com   
作者简介:  任超,硕士研究生,南昌航空大学,材料工程专业。主要从事金属材料热处理及材料表面改性研究。
罗军明,教授,博士。主要从事金属基复合材料、粉末冶金材料和材料表面改性研究,发表论文80余篇。主持和参加国家和省部级科研以上项目30项,获省部级科学进步奖2项。
引用本文:    
任超, 罗军明, 陈宇海, 黄俊, 徐吉林. 喷丸对TC4合金微弧氧化涂层磨损和腐蚀行为的影响[J]. 材料导报, 2020, 34(18): 18081-18085.
REN Chao, LUO Junming, CHEN Yuhai, HUANG Jun, XU Jilin. Effect of Shot Peening on Wear and Corrosion Behavior of Micro-arc Oxidation Coating of TC4 Alloy. Materials Reports, 2020, 34(18): 18081-18085.
链接本文:  
http://www.mater-rep.com/CN/10.11896/cldb.19090097  或          http://www.mater-rep.com/CN/Y2020/V34/I18/18081
1 Li L, Sun J K, Meng X J. Titanium Industry Progress, 2004, 21(5), 19(in Chinese).
李梁, 孙健科, 孟祥军. 钛工业进展, 2004, 21(5), 19.
2 Luan W L, Tu S D. China Mechanical Engineering, 2005, 16(15), 1405(in Chinese).
栾伟玲, 涂善东. 中国机械工程, 2005, 16(15), 1405.
3 Aliofkhazraei, Rouhaghdam S. Surface & Coatings Technology, 2010, 205(7), S41.
4 Gujba A K, Medraj M. Materials, 2014, 7(12), 7925.
5 Léo C, Jawad B, Brian M G, et al. Journal of Materials Processing Technology, 2018, 264(2), 91.
6 Unal O, Varol R. Applied Surface Science, 2014, 290(290), 40.
7 Luo J M, Chen Y H, Xu J L, et al. Surface & Coatings Technology, 2019, 164.
8 Todt J, Pitonak R, Köpf A, et al. Surface & Coatings Technology, 2014, 258(6922), 1119.
9 Ma K J, Bosta M M S A, Wu W T. Surface & Coatings Technology, 2014, 259, 318.
10 Babaei M, Dehghanian C, Vanaki M. Applied Surface Science, 2015, 357, 712.
11 Venkateswarlu K, Suresh S, Rameshbabu N, et al. Materials Science Forum, 2013, 688.
12 Xiao F, Du D F, Chen H, et al. Hot Working Technology, 2018, 47(10), 7(in Chinese).
肖峰, 杜东方, 陈辉, 等. 热加工工艺, 2018, 47(10), 7.
13 Khanna R, okubo T, Matsushita T, et al. Materials Science & Enginee-ring C-Materials for Biological Applications, 2016, 69,1229.
14 Shokouhfar M, Allahkaram S. Surface & Coatings Technology, 2017, 309, 767.
15 Arslan E, Totik Y, Demirci E E, et al. Surface & Coatings Technology, 2013, 214(15), 1.
16 Williamson G K, Hall W H. Acta Metallurgica, 1953, 1(1), 22.
17 Kumar S, Chattopadhyay K, Singh V, et al. International Journal of Surface Science and Engineering, 2017, 11(1), 23
18 Jelliti S, Richard C, Retraint D, et al. Surface & Coatings Technology, 2013, 224, 82.
19 Azar V, Hashemi B, Yazdi M R. Surface & Coatings Technology, 2010, 204, 3546.
20 Wang Y,Lei T, Guo L, g et al. Applied. Surface Science, 2006, 252, 8113.
21 Sharma S, Sangal S, Mondal K.Wear, 2013, 300, 82.
22 Khorasanian M, Dehghan A, Shariat M H, et al. Surface & Coatings Technology, 2011, 206, 1495.
23 Lijie W, Yazhe X, Hongbo W, et al, Rare Metals, 2010, 29, 604.
24 Jelliti S, Richard C, Retraint D, Surface & Coatings Technology, 2013, 224, 82.
25 Yu J K, Han E H, Lu L, et al. Journal of Materials Science, 2005, 40, 1019.
26 Jindal S, Bansal R, Singh B P, et al.Journal of Oral Implantology, 2014,40, 347.
27 Balusamy T, Kumar S, Narayanan T S N S. Corrosion Science,2010,52, 3826.
[1] 赵秋萍, 钱庆一, 张斌, 牟志星, 张兴凯. 质子交换膜燃料电池金属双极板表面碳基防护镀层研究进展[J]. 材料导报, 2020, 34(Z1): 395-399.
[2] 赵静, 王天鹏, 张淮浩. 磁场作用下十二烷基苯磺酸钠对阳极铝箔的缓蚀性能及比电容的影响[J]. 材料导报, 2020, 34(6): 6156-6160.
[3] 李慧莹, 赵君文, 戴光泽, 韩靖, 李旭嘉. 钼酸钠含量对无铬锌铝涂层性能的影响[J]. 材料导报, 2020, 34(2): 2105-2109.
[4] 谭金花, 孙荣禄, 牛伟, 刘亚楠, 郝文俊. TC4合金激光熔覆材料的研究现状[J]. 材料导报, 2020, 34(15): 15132-15137.
[5] 朱守东, 张继旺, 易科尖, 苏凯新, 李行, 张金鑫. 微粒子喷丸工艺对EA4T车轴钢表面性能和疲劳强度的影响[J]. 材料导报, 2020, 34(14): 14181-14186.
[6] 卢勇, 冯辉霞. 转化膜致密化及耐蚀性能提升工艺优化进展[J]. 材料导报, 2020, 34(13): 13160-13166.
[7] 谭金花, 孙荣禄, 牛伟, 刘亚楠, 郝文俊. 激光扫描速度对TC4合金表面激光熔覆复合涂层组织及性能的影响[J]. 材料导报, 2020, 34(12): 12094-12100.
[8] 周婉秋, 赵玉明, 刘晓安, 杨佳宇, 姜文印, 辛士刚, 康艳红. 1-乙基-3-甲基咪唑硫酸乙酯盐离子液体中采用电化学法合成聚苯胺薄膜及其耐蚀性[J]. 材料导报, 2020, 34(12): 12152-12157.
[9] 宋涛, 杨杰, 赵松海, 尚海涛, 白超超. 石膏基自流平砂浆耐磨性能研究[J]. 材料导报, 2019, 33(Z2): 239-241.
[10] 肖忆楠, 乔岩欣, 李月明, 盛立远, 赖琛, 奚廷斐. 医用钛及钛合金表面改性技术的研究进展[J]. 材料导报, 2019, 33(Z2): 336-342.
[11] 曾德鹏, 余森, 王岚, 于振涛, 刘印, 盖晋阳, 代晓军. 医用金属材料表面自身纳米化研究进展[J]. 材料导报, 2019, 33(Z2): 343-347.
[12] 薛艺, 田青超. 硬质合金切削刀具研究进展[J]. 材料导报, 2019, 33(z1): 353-357.
[13] 毕凤琴, 周帮, 王勇. 合金化对不锈钢耐蚀性能影响的研究进展[J]. 材料导报, 2019, 33(7): 1206-1214.
[14] 张贤琳, 王晓琳, 马建威, 李宝娥, 李海鹏, 刘世敏, 梁春永, 王洪水. 钛表面微弧氧化结构和成分对其润湿性的影响[J]. 材料导报, 2019, 33(24): 4035-4039.
[15] 常钦鹏, 陈友媛, 安振东, 王磊. B30铜镍合金表面植酸转化膜的制备工艺研究[J]. 材料导报, 2019, 33(23): 3876-3881.
[1] Wei ZHOU, Xixi WANG, Yinlong ZHU, Jie DAI, Yanping ZHU, Zongping SHAO. A Complete Review of Cobalt-based Electrocatalysts Applying to Metal-Air Batteries and Intermediate-Low Temperature Solid Oxide Fuel Cells[J]. Materials Reports, 2018, 32(3): 337 -356 .
[2] Yanzhen WANG, Mingming CHEN, Chengyang WANG. Preparation and Electrochemical Properties Characterization of High-rate SiO2/C Composite Materials[J]. Materials Reports, 2018, 32(3): 357 -361 .
[3] Yimeng XIA, Shuai WU, Feng TAN, Wei LI, Qingmao WEI, Chungang MIN, Xikun YANG. Effect of Anionic Groups of Cobalt Salt on the Electrocatalytic Activity of Co-N-C Catalysts[J]. Materials Reports, 2018, 32(3): 362 -367 .
[4] Dongyong SI, Guangxu HUANG, Chuanxiang ZHANG, Baolin XING, Zehua CHEN, Liwei CHEN, Haoran ZHANG. Preparation and Electrochemical Performance of Humic Acid-based Graphitized Materials[J]. Materials Reports, 2018, 32(3): 368 -372 .
[5] Huanchun WU, Fei XUE, Chengtao LI, Kewei FANG, Bin YANG, Xiping SONG. Fatigue Crack Initiation Behaviors of Nuclear Power Plant Main Pipe Stainless Steel in Water with High Temperature and High Pressure[J]. Materials Reports, 2018, 32(3): 373 -377 .
[6] Miaomiao ZHANG,Xuyan LIU,Wei QIAN. Research Development of Polypyrrole Electrode Materials in Supercapacitors[J]. Materials Reports, 2018, 32(3): 378 -383 .
[7] Qingshun GUAN,Jian LI,Ruyuan SONG,Zhaoyang XU,Weibing WU,Yi JING,Hongqi DAI,Guigan FANG. A Survey on Preparation and Application of Aerogels Based on Nanomaterials[J]. Materials Reports, 2018, 32(3): 384 -390 .
[8] Yunzi LIU,Wei ZHANG,Zhanyong SONG. Technological Advances in Preparation and Posterior Treatment of Metal Nanoparticles-based Conductive Inks[J]. Materials Reports, 2018, 32(3): 391 -397 .
[9] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[10] Lanyan LIU,Jun SONG,Bowen CHENG,Wenchi XUE,Yunbo ZHENG. Research Progress in Preparation of Lignin-based Carbon Fiber[J]. Materials Reports, 2018, 32(3): 405 -411 .
Viewed
Full text


Abstract

Cited
  Shared   
  Discussed