Abstract: In this paper, Cu-Mn-Ni-Sn brazing filler metal was used to braze Mn-Cu alloy and 430 stainless steel (SS) by ordinary brazing (as-cast brazing filler metal, 850 ℃) and SIMA-imitated brazing process (rolled brazing filler metal, semi-solid temperature 790 ℃), respectively. The effects of brazing temperature on the microstructures, the formation of compounds and the mechanical properties of the joints were studied. In ordinary brazed joint, (Mn, Fe, Cr) solid solution diffusion layer was formed at the interface between stainless steel and brazing seam, however, cracks were formed at the interface between the diffusion layer and the brazing seam. The penetration of Sn-rich phase at grain boundaries of Mn-Cu alloy promoted the melting of alloy. The excessive dissolution of SS and partial melting of Mn-Cu alloy resulted in the formation of a large number of needle-like Mn-Cr-Cu-Fe compounds in the brazing seam. In SIMA-imitated brazed joint, the interface between stainless steel and brazing seam was well bonded. At the semi-solid temperature, the diffusion of filler metal to SS was decreased, and the dissolution of SS to filler metal was decreased as well. At the Mn-Cu alloy side, the penetration of Sn-rich phase along the grain boundaries was also effectively suppressed. Since the interaction between the substrates and filler metal was weaker, the amount of needle-like compounds decreased obviously in the brazing seam. In shear test, both brazed joints were broken in the distribution area of needle-like compounds in the brazing seam. The shear strength of ordinary brazed joint was 173 MPa, and that of SIMA-imitated brazed joint was 230 MPa.
1 Yin F X, Nagai K, Watanabe K, et al. Materials Transactions, 2003, 44(9), 1671. 2 Li D, Liu W B, Li N, et al. Advanced Engineering Materials, 2017, 19(12), 1. 3 Zhang B G, Zhao J, Li X P, et al. Transactions of Nonferrous Metals Society of China, 2014, 24(12), 4059. 4 Yan W. Study on electron beam welding performance of dissimilar mate-rial manganese-copper alloy/steel. Master’s Thesis, Harbin University of Science and Technology, China, 2009(in Chinese). 燕伟. 锰铜合金/钢异种材料电子束焊接性研究. 硕士学位论文, 哈尔滨理工大学, 2009. 5 Zheng Y, Li N, Yan J Z, et al. Materials Science and Engineering a-Structural Materials Properties Microstructure and Processing, 2016, 661, 25. 6 Roy R K, Singh S, Gunjan M K, et al. Fusion Engineering and Design, 2011, 86(4-5), 452. 7 Na H S, Kim J K, Jeong B Y, et al. Metals and Materials International, 2007, 13(6), 511. 8 Xu Z W, Li Z W, Xu L, et al. Science and Technology of Welding and Joining, 2019, 24(2),163. 9 Xu H B, Luo Q X, Zhou B F, et al. Materials & Design, 2012, 34,452. 10 Shi L, Yan J C, Han Y F, et al. Journal of Materials Engineering, 2010 (10), 65(in Chinese). 石磊, 闫久春, 韩焱飞, 等. 材料工程, 2010 (10), 65. 11 Rao L S, Ojha S N, Jha A K. International Journal of Metal Casting, 2018, 12(3), 523. 12 Lin C W, Hung F Y, Lui T S. Metals, 2016, 6 (8), 1. 13 Wang J, Xiao H, Wu L B, et al. Acta Metallurgica Sinica, 2014, 50(5), 567(in Chinese). 王佳, 肖寒, 吴龙彪, 等. 金属学报, 2014,50(5), 567. 14 Song Y B, Park K T, Hong C P. Materials Transactions, 2006, 47(4), 1250. 15 Easton D, Wood J, Rahimi S, et al. IEEE Transactions on Plasma Science, 2016, 44(9), 1625. 16 Qu D D, Zhou Z J, Yum Y J, et al. Journal of Nuclear Materials, 2014, 455(1), 130. 17 Wang Z, Qu W Q, Zhuang H S. Materials Letters, 2016, 182, 75.
渝公网安备50019002502923号 版权所有：《材料导报》编辑部
2020, Vol. 34 
