Abstract: The WC-10Co-4Cr powders were prepared by using rapid agglomerate sintering method, and the coatings were sprayed onto steel substrate by high velocity oxygen fuel (HVOF) technology. A study was conducted with regard to the effects of sintering temperature on the WC-10Co-4Cr powders, as well as on the microstructure and wear resistance of WC-10Co-4Cr coatings. As suggested by the results, when the sintering temperature was raised from 1 250 ℃ to 1 450 ℃, the density of WC-10Co-4Cr powders increased, the average particle size of powders decreased, and the uniformity of them declined. With the increase of powder sintering temperature, the internal defects of the WC-10Co-4Cr coa-tings increase, leading to weakened wear resistance. In this case, the primary wear mechanism varied from the micro-cutting of the binder phase to delamination wear.
周维, 樊坤阳, 黄淙, 刘子京, 万维财, 贡太敏. 烧结温度对团聚高温快速烧结WC-10Co-4Cr粉末及其HVOF涂层性能的影响[J]. 材料导报, 2022, 36(6): 20120041-6.
ZHOU Wei, FAN Kunyang, HUANG Cong, LIU Zijing, WAN Weicai, GONG Taimin. Effect of Sintering Temperature on the Properties of Rapid Agglomerate Sintered WC-10Co-4Cr Powders and Its HVOF Coatings. Materials Reports, 2022, 36(6): 20120041-6.
1 Wang H B, Song X Y, Gao Y, et al. Materials Science and Engineering of Powder Metallurgy, 2011, 16(4), 492. 2 Yang Q, Senda T, Ohmori A. Wear, 2003, 254(1-2), 23. 3 Vernhes L, Azzi M, Klemberg-Sapieha J E. Materials Chemistry and Phy-sics, 2013, 140(2-3), 522. 4 Tian Y, Ma J H, Li Z D. Thermal Spray Technology, 2010(3), 33 (in Chinese). 田晔, 马江虹, 李振铎. 热喷涂技术, 2010(3), 33. 5 Gong T M. Study on preparation of high performance cemented carbide spraying powder for HVOF and its basic mechanism. Master's Thesis, Central South University, China, 2012(in Chinese). 贡太敏. HVOF用高性能硬质合金喷涂粉末的制备技术及其基础理论研究. 硕士学位论文,中南大学, 2012. 6 Wu C H. Cemented Carbide, 1999(4), 201 (in Chinese). 吴冲浒. 硬质合金,1999(4), 201. 7 Wu C H, Xie H W, Zheng A Q, et al. Materials Science and Engineering of Powder Metallurgy, 2013, 18(2), 309 (in Chinese). 吴冲浒, 谢海唯, 郑爱钦, 等.粉末冶金材料科学与工程, 2013, 18(2),309. 8 Liu K, Wang Z, Yin Z, et al. Ceramics International, 2018, 44(15), 18711. 9 Bao X Y, Zhang F, Lu Z C, et al. Materials Reports B: Research Papers, 2017, 31(8), 65 (in Chinese). 鲍贤勇,张峰,鲁忠臣,等.材料导报:研究篇, 2017,31(8), 65. 10 Zuo X T, Yao P P, Gong T M, et al. Materials Science and Engineering of Powder Metallurgy, 2015(1), 106 (in Chinese). 左晓婷, 姚萍屏, 贡太敏,等. 粉末冶金材料科学与工程, 2015(1), 106. 11 Ding X, Cheng X D, Li C, et al. The International Journal of Advanced Manufacturing Technology, 2018, 96(5-8), 1625. 12 Gong T, Yao P, Zuo X,et al. Wear, 2016, 362, 135. 13 Ji G J, Wei M X, Wang D F. Thermal Spray Technology, 2017, 9(2), 17 (in Chinese). 冀国娟, 魏明霞, 王大锋. 热喷涂技术,2017, 9(2), 17. 14 Wu Y, Hong S, Zhang J F. International Journal of Refractory Metals and Hard Materials, 2012, 32,21. 15 Mi P, Wang T, Ye F. International Journal of Refractory Metals and Hard Materials, 2017, 69, 158. 16 Wei S U, Sun Y, Yang H, et al. Transactions of Nonferrous Metals Society of China, 2015, 25(4), 1194. 17 Fu J, Song X Y, Wei C B, et al. Rare Metal Materials an Engineering, 2014, 43(8), 1928 (in Chinese). 付军, 宋晓艳, 魏崇斌, 等. 稀有金属材料与工程, 2014,43(8), 1928. 18 Pirso J, Letunovitš S, Viljus M. Wear, 2004, 257(3), 257. 19 Espinosa L, Bonache V, Salvador M D. Wear, 2011, 272(1), 62. 20 Huang B, Wu Q D, Wei X L, et al. Suface Technology, 2020,49(1), 285 (in Chinese). 黄博, 吴庆丹, 魏新龙, 等. 表面技术, 2020, 49(1), 285. 21 Chen S Y, Ma G Z, He P F, et al. Journal of Inorganic Materials, 2018, 266(8), 895 (in Chinese). 陈书赢, 马国政, 何鹏飞, 等. 无机材料学报, 2018, 266(8), 895.