Please wait a minute...
《材料导报》期刊社  2018, Vol. 32 Issue (10): 1612-1617    https://doi.org/10.11896/j.issn.1005-023X.2018.10.008
  材料研究 |
中间退火及成品退火速率对高压阳极铝箔微观组织的影响
王运雷1,张 杰2,龚丽娟3
1 重庆文理学院材料与化工学院,重庆 402160;
2 重庆文理学院机电工程学院,重庆 402160;
3 重庆文理学院安全管理处,重庆 402160
Effect of Inter-annealing and Final-annealing Heating Rate on Microstructure of Aluminum Foils for High-voltage Anode
WANG Yunlei1, ZHANG Jie2, GONG Lijuan3
1 School of Materials and Chemical Engineering, Chongqing University of Arts and Sciences, Chongqing 402160;
2 School of Mechanical and Electrical Engineering, Chongqing University of Arts and Sciences, Chongqing 402160;
3 Security Department, Chongqing University of Arts and Sciences, Chongqing 402160
下载:  全 文 ( PDF ) ( 7720KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 采用不同中间退火温度及成品退火速率对高压阳极铝箔进行处理,并利用EBSD及XRD技术分析其微观组织结构,尤其是织构的变化规律。结果表明,中间退火温度对后续成品退火中形成立方织构起到了关键作用,这可能是由于低温中间退火保留了大量的形变储能,为成品退火时立方织构的形成增加了形核核心。同时,低的中间退火温度造成立方织构较理想位置偏转程度更大。随着成品退火加热速率的增大,铝箔再结晶分数及再结晶晶粒尺寸逐渐减小,这是由于退火加热速率的增大(低于临界加热速率),缩短了晶界迁移的时间,减缓了再结晶的发生。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
王运雷
张 杰
龚丽娟
关键词:  中间退火  高纯铝箔  退火加热速率  微观组织  织构    
Abstract: The effect of the inter-annealing temperature and heating rate of final annealing on the microstructure of high-vol-tage anode aluminum foils was investigated by electron back scattered diffraction (EBSD) and X-ray diffraction (XRD). The results demonstrated that the inter-annealing temperature played a key role on the formation of cube texture in the final products, because the low inter-annealing retained lots of deformation stored energy and provided great driving force for the nucleation. Simultaneously, the cube texture deflected dramatically from the idea position at a lower inter-annealing temperature. With the increase of annealing heating rate during final annealing, the fraction and grain size of recrystallization decreased gradually, because a higher annealing heating rate (below the critical heating rate) reduced the time available for grain boundary migration and retarded the recrystallization.
Key words:  inter-annealing    high purity aluminum foil    annealing heating rate    microstructure    texture
               出版日期:  2018-05-25      发布日期:  2018-07-06
ZTFLH:  TG146  
基金资助: 校级项目资助(Y2013JD46)
作者简介:  王运雷:男,1985年生,博士,讲师,主要研究方向为铝及铝合金形变加工及微观机理 E-mail:wangyunlei@cqu.edu.cn
引用本文:    
王运雷,张 杰,龚丽娟. 中间退火及成品退火速率对高压阳极铝箔微观组织的影响[J]. 《材料导报》期刊社, 2018, 32(10): 1612-1617.
WANG Yunlei, ZHANG Jie, GONG Lijuan. Effect of Inter-annealing and Final-annealing Heating Rate on Microstructure of Aluminum Foils for High-voltage Anode. Materials Reports, 2018, 32(10): 1612-1617.
链接本文:  
http://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2018.10.008  或          http://www.mater-rep.com/CN/Y2018/V32/I10/1612
1 Yang H, Mao W M. Present research status and technology deve-lopment of aluminum foil for electrolytic capacitor [J]. Materials Review,2005,19(9):1(in Chinese).
杨宏,毛卫民.铝电解电容器铝箔的研究现状和技术发展[J].材料导报,2005,19(9):1.
2 Sun Z Y, Xu Y L, Cao W Z, et al. Effect of recrystal granularity of high-purity aluminum foil on it’s specific capacitance [J]. Electron Component Materials,1995,14(4):45(in Chinese).
孙中禹,徐友龙,曹婉真,等.高纯铝箔再结晶晶粒度对比容的影响[J].电子元件与材料,1995,14(4):45.
3 Engler O, Huh M Y. Evolution of the cube texture in high purity aluminum capacitor foils by continuous recrystallization and subsequent grain growth [J]. Materials Science and Engineering A,1999,271:371.
4 Huang G J, Zhang Jing, Wang Y L, et al. Abnormal recrystallization behavior of high purity aluminum foil[C]∥13th International Conference on Aluminum Alloys (ICAA-13).Pennsylvania, US,2012.
5 Li N K, Ye S F. Effect of process factors on the cube texture of high purity aluminum foils [J]. Light Alloy Processing Technology,1993,21(11):19(in Chinese).
李念奎,叶淑芬.工艺因素对高纯铝箔立方织构的影响[J].轻合金加工技术,1993,21(11):19.
6 Li N K. A process to improve the cube texture of high purity aluminum foils [J]. Light Alloy Processing Technology,1995,23(4):18(in Chinese).
李念奎.提高高纯铝箔立方织构的工艺途径[J].轻合金加工技术,1995,23(4):18.
7 Xu J, Mao W M, Feng H P, et al. Influence of Cu content on the recrystallization texture of aluminum foil for high voltage anode electrolytic capacitor [J]. Journal of University of Science and Technology Beijing,2002,24(2):133(in Chinese).
徐进,毛卫民,冯慧平,等.Cu对高压电解电容器阳极铝箔再结晶织构的影响[J].北京科技大学学报,2002,24(2):133.
8 Zhang X M, Meng Y, Zhou Z P. Effect of Fe impurity on recrystallization textures and specific capacitances of high pure aluminum foils [J]. The Chinese Journal of Nonferrous Metals,1999,9(1):19(in Chinese).
张新明,孟亚,周卓平.Fe杂质对高纯铝箔再结晶织构及比电容的影响[J].中国有色金属学报,1999,9(1):19.
9 Liu C M, Zhang X M, Zhou H Z, et al. Influence of trace Fe and annealing on recrystallization textures of high-purity aluminum foils [J]. Heat Treatment of Metals,2002,27(3):21(in Chinese).
刘楚明,张新明,周鸿章,等.铁含量及退火对高纯铝箔再结晶织构的影响[J].金属热处理,2002,27(3):21.
10 Xiao Y Q, Zhang X M, Jin L. Effect of microstructures in electrolytic capacitor Al foils on specific capacitance [J]. Materials Review,2003,17(6):80(in Chinese).
肖亚庆,张新明,靳丽.微观组织对电解电容器铝箔比电容的影响[J].材料导报,2003,17(6):80.
11 Xu J, Mao W M, Feng H P, et al. Influence of annealing process on cube texture formation in aluminum foil of high voltage anode electrolytic capacitor [J]. The Chinese Journal of Nonferrous Metals,2001,11(S2):42(in Chinese).
徐进,毛卫民,冯慧平,等.退火加热过程对高压电解电容器阳极铝箔立方织构的影响[J].中国有色金属学报,2001,11(S2):42.
12 Liu C M, Zhang X M, Chen Z Y, et al. Effect of intermediate annealing on cubic texture of high-purity aluminum foils [J]. Heat Treatment of Metals,2001,26(3):28(in Chinese).
刘楚明,张新明,陈志永,等.中间退火对高纯铝箔立方织构的影响[J].金属热处理,2001,26(3):28.
13 Attallah M M, Strangwood M, Davis C L. Influence of the heating rate on the initiation of primary recrystallization in a deformed Al-Mg alloy [J]. Scripta Materialia,2010,63:371.
14 Ma Y X, Yang P, Yu Y N, et al. Micro-process of cube texture formation in high purity electronic aluminum foils [J]. Journal of University of Science and Technology Beijing,2003,25(2):147(in Chinese).
马英晓,杨平,余永宁,等.高纯电子铝箔立方织构形成的微观过程[J].北京科技大学学报,2003,25(2):147.
15 Liu C M, Zhang X M, Zhang Z Y, et al. Effect of production procedure of aluminum anode foils on cube texture [J]. Materials Review,2000,14(6):19(in Chinese).
刘楚明,张新明,张志永,等.高压阳极电容铝箔生产工艺对立方织构的影响[J].材料导报,2000,14(6):19.
16 Zhao S L, Zheng Z Q. The effect of cold deformation and annealing on the cube texture of Al foil [J]. Journal of Wuhan University of Technology,2001,23(6):31(in Chinese).
赵素玲,郑子樵.退火和冷轧变形对电容铝箔立方织构的影响[J].武汉理工大学学报,2001,23(6):31.
17 Liu C M, Zhang X M, Zhou H Z, et al. Effect of multi-stage annealing on recrystallization textures of high purity aluminum foils [J]. Heat Treatment of Metals,2001,26(9):38(in Chinese).
刘楚明,张新明,周鸿章,等.分级退火对高纯铝箔再结晶织构的影响[J].金属热处理,2001,26(9):38.
[1] 雷林, 杨庆波, 张志清, 樊祥泽, 李旭, 杨谋, 邓赞辉. AA2195铝锂合金多道次压缩行为及微观组织演变[J]. 材料导报, 2019, 33(z1): 348-352.
[2] 康凤, 陈文, 胡传凯, 林军, 夏祥生, 吴洋. 时效参数对Ti12LC钛合金组织及性能的影响[J]. 材料导报, 2019, 33(z1): 326-328.
[3] 张冠星, 薛行雁, 龙伟民, 钟素娟, 孙华为, 董宏伟. BAg45CuZn钎料硫化处理组织和性能演变特性[J]. 材料导报, 2019, 33(z1): 425-427.
[4] 陈琛辉, 蒋璐瑶, 刘成龙, 黄伟九, 郭勇义, 胥桥梁. 搅拌摩擦加工细晶TA2工业纯钛晶粒长大规律[J]. 材料导报, 2019, 33(8): 1367-1370.
[5] 何承绪, 涂蕴超, 孟利, 杨富尧, 刘洋, 马光, 韩钰, 陈新. 超薄取向硅钢组织及织构与磁性能的关系[J]. 材料导报, 2019, 33(6): 1027-1031.
[6] 曹聪聪, 李文亚, 杨康, 李成新, 纪纲. 基体硬度和热学性质对冷喷涂TC4钛合金涂层组织和力学性能的影响[J]. 材料导报, 2019, 33(2): 277-282.
[7] 徐强, 洪悦, 李楠, 伍翠兰. 气体氮碳共渗中NH3和CO流量对低碳钢渗层组织及其性能的影响[J]. 材料导报, 2019, 33(2): 330-334.
[8] 郑国明, 李磊, 毛小南, 蔡建华, 吴聪, 雷磊. 钛合金BCC↔HCP相变的变体选择及其对晶体取向的影响[J]. 材料导报, 2019, 33(17): 2910-2917.
[9] 赵猛,张亮,熊明月. Sn-Cu系无铅钎料的研究进展及发展趋势[J]. 材料导报, 2019, 33(15): 2467-2478.
[10] 王剑豪,薛松柏,吕兆萍,王刘珏,刘晗. 纳米颗粒增强无铅钎料的研究进展[J]. 材料导报, 2019, 33(13): 2133-2145.
[11] 孟强, 车倩颖, 王快社, 张坤, 王文, 黄丽颖, 彭湃, 乔柯. 铝铜异种材料搅拌摩擦焊接接头微观组织与性能[J]. 材料导报, 2019, 33(12): 2030-2034.
[12] 陈宇强, 宋文炜, 潘素平, 刘文辉, 宋宇锋, 张浩. 沉积颗粒对7N01-T6铝合金疲劳裂纹扩展行为的影响[J]. 材料导报, 2019, 33(10): 1697-1701.
[13] 蔡惠坤, 翁泽钜, 顾开选, 王凯凯, 郑建朋, 王俊杰. 硬质合金深冷处理研究进展[J]. 材料导报, 2019, 33(1): 175-182.
[14] 俞良良, 张郑, 王快社, 王文, 贾少伟. 搅拌摩擦加工对AZ31镁合金微观组织及力学性能的影响[J]. 《材料导报》期刊社, 2018, 32(8): 1289-1293.
[15] 丁雨田, 马元俊, 豆正义, 刘建军, 高钰璧, 孟斌. 固溶处理温度对GH3625合金热挤压管材微观组织和力学性能的影响[J]. 《材料导报》期刊社, 2018, 32(8): 1311-1317.
[1] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6] XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg98.5Zn0.5Y1 Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7] ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed