Please wait a minute...
材料导报  2019, Vol. 33 Issue (8): 1422-1426    https://doi.org/10.11896/cldb.17120032
  高分子与聚合物基复合材料 |
BEM含量对MAA-EA-MMA共聚物乳液的pH响应性研究
刘国军1, 张生义1, 钟明月1, 张桂霞1, 王艳1, 余大平2
1 大连工业大学纺织与材料工程学院,大连 116034
2 广州市鼎茂新材料科技有限公司,广州 510240
pH Response of Hydrophobic Modified Alkali Soluble Polymer Emulsion with Different Content of BEM
LIU Guojun1, ZHANG Shengyi1, ZHONG Mingyue1, ZHANG Guixia1, WANG Yan1, YU Daping2
1 School of Testile and Material Engineering, Dalian Polytechnic University, Dalian 116034
2 DM Material Tech Co., Ltd., Guangzhou 510240
下载:  全 文 ( PDF ) ( 1931KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 采用乳液聚合工艺合成了二十二烷基聚氧乙烯醚甲基丙烯酸酯(BEM)含量不同的疏水改性碱溶性甲基丙烯酸(MAA)-丙烯酸乙酯(EA)-甲基丙烯酸甲酯(MMA)聚合物乳液(HASE)。通过控制NaOH的加入量调节大分子链中MAA的中和度,即NaOH/MAA的物质的量比a,研究了pH值对HASE体系透光率和表观黏度的影响,分析了pH值在相态变化过程中的作用,以赫谢尔-巴尔克莱三参数流变方程模拟流变曲线,探讨pH值和BEM含量在pH值二次增加时对流变行为的影响。结果表明:pH值在NaOH/MAA的物质的量比a≈0.3~0.6 时略降低;pH值最低时,亲水和静电斥力作用与疏水作用达到平衡,HASE分子由充分溶胀的乳胶粒子相态变为溶液;BEM含量增多,中和反应和相态转变的pH值越高;表观黏度、屈服应力、稠度系数和流变指数都存在pH(约为6.7)敏感性,且BEM含量越多,敏感点的pH值越高。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
刘国军
张生义
钟明月
张桂霞
王艳
余大平
关键词:  疏水缔合  碱溶性聚合物  乳液  流变学  pH值  数学模拟    
Abstract: The hydrophobic modified alkali soluble polymer emulsion (HASE) with different content of methylacrylic ester of ethoxylated (25 EO) C22 (BEM) were synthesized by emulsion polymerization method. Through controlling the mole ratio a of NaOH/MAA to adjust the neutralization degree of MAA in the macromolecular chain , the influence of pH on the transmittance and apparent viscosity of HASE system, and the function of pH in the process of phase transition were investigated. The rheological curves were simulated with three-parametric Herschel-Buckley model equation, and the effect of pH and BEM content on the rheological behavior at the secondary increase stage of pH was discussed. The results show that the pH value slightly decreases when the molar ratio of NaOH/MAA is 0.3 to 0.6, and the hydrophilic interaction and electrostatic repulsion are in balance with hydrophobic interaction at the lowest pH, meanwhile, the HASE molecule is turned into a solution from a fully swelled latex particle. The BEM content increases, the pH of the neutralization reaction and phase transition are higher; the apparent viscosity, yield stress, consistency coefficient and rheological index all have the sensitivity of pH (about 6.7), and the more BEM content, the higher the pH of the sensitive point.
Key words:  hydrophobic association    alkali-soluble polymer    emulsions    rheology    pH value    mathematical simulation
               出版日期:  2019-04-25      发布日期:  2019-04-28
ZTFLH:  TQ317.3  
基金资助: 国家自然科学基金(51503023);辽宁省教育厅优秀人才项目(LJQ2012046)
通讯作者:  tysxlgj@163.com   
作者简介:  刘国军,大连工业大学纺织与材料工程学院副教授。2003年在中山大学高分子化学与物理专业获博士学位,目前主要从事高分子的设计与合成研究,发表论文50余篇,授权发专利6项。张桂霞,大连工业大学纺织与材料工程学院实验师。2002年毕业于青岛科技大学,获材料学硕士学位。目前主要从事高分子材料成型加工及实验室维护与管理,发表论文60余篇,授权发明专利6项。
引用本文:    
刘国军, 张生义, 钟明月, 张桂霞, 王艳, 余大平. BEM含量对MAA-EA-MMA共聚物乳液的pH响应性研究[J]. 材料导报, 2019, 33(8): 1422-1426.
LIU Guojun, ZHANG Shengyi, ZHONG Mingyue, ZHANG Guixia, WANG Yan, YU Daping. pH Response of Hydrophobic Modified Alkali Soluble Polymer Emulsion with Different Content of BEM. Materials Reports, 2019, 33(8): 1422-1426.
链接本文:  
http://www.mater-rep.com/CN/10.11896/cldb.17120032  或          http://www.mater-rep.com/CN/Y2019/V33/I8/1422
1 Dossantos Z M, Wanderley N A O, Dantas T N C, et al. European Polymer Journal, 2007, 43, 3314.
2 Wang C, Tam K C, Jenkinsb R D, et al. Physical Chemistry Chemistry Physical, 2000, 2, 1967.
3 Chen J, Xu K, Chen M C. Polymer Materials Science & Engineering, 2013, 29(4), 37(in Chinese).
陈嘉, 许凯, 陈鸣才.高分子材料科学与工程, 2013, 29(4),37.
4 Chasseniieux C, Nicolai T, Benyahia L. Current Opinion in Colloid & Interface Science, 2011, 16, 18.
5 Moraes R P, Graillat C, Jeanson G, et al. Journal of Colloid and Interface Science, 2010, 352, 19.
6 Jassal M, Acharya B N, Bajaj P. Journal of Applied Polymer Science, 2003, 89, 1430.
7 Wang C, Jiang X B, Zhu X L, et al. Acta Chimica Sinica, 2010, 68(7), 689(in Chinese).
王晨, 姜绪宝, 朱晓丽, 等. 化学学报, 2010, 68(7), 689.
8 Zhu X L, Kong X Z, Liu Y X, et al. Acta Chimica Sinica, 2008, 66(22), 2525(in Chinese).
朱晓丽, 孔祥正, 刘永祥, 等.化学学报, 2008, 66(22), 2525.
9 Kong X Z, Wang C, Jiang X B, et al. Chinese Chemical Letters, 2010, 21, 616.
10 De Souza T V, De Souza P R S, Pereira M R, et al. Progress in Organic Coatings, 2017, 106, 1.
11 Dundua A, Landfester K, Taden A. Polymer, 2014, 55, 3543.
12 Snuparek J, Quadrat O, Horsky J. Progress in Organic Coatings, 2005, 54, 99.
13 Ng W K, Tam K C, Jenkins R D. Polymer, 2001, 42, 249.
14 Chen H, Wu X Y, Ye Z B, et al. Acta Physico-Chimica Sinica, 2012, 28(4), 903(in Chinese).
陈洪, 吴晓艳, 叶仲斌, 等.物理化学学报, 2012, 28(4), 903.
[1] 王家滨, 牛荻涛. 喷射混凝土的硝酸侵蚀:孔溶液H+与NO3-的扩散规律及侵蚀机理[J]. 材料导报, 2019, 33(6): 991-999.
[2] 翟乐, 吉海峰, 姚艳梅, 瞿雄伟. 利用聚丙烯酸正丁酯@聚甲基丙烯酸甲酯核/壳结构聚合物增韧氰酸酯树脂[J]. 材料导报, 2019, 33(4): 705-708.
[3] 皮茂, 张守村, 魏杰, 李伟达. 采用高内相乳液模板法制备葡萄糖基/麦芽糖基大孔材料及其形貌表征[J]. 材料导报, 2019, 33(16): 2804-2807.
[4] 王岚, 崔世超, 常春清. 基于流变学与黏弹性理论的温拌胶粉改性沥青的高温性能研究[J]. 材料导报, 2019, 33(14): 2386-2391.
[5] 张利波, 王璐, 曲雯雯, 徐盛明, 张家麟. Al2O3基石油加氢脱硫催化剂研究现状与进展[J]. 《材料导报》期刊社, 2018, 32(5): 772-779.
[6] 王静, 李坚, 汪剑辉, 郑力, 李浪涛. 用于混凝土表面放射性沾染清除的剥离型膜材料研究[J]. 材料导报, 2018, 32(20): 3673-3676.
[7] 韩冬冬,陈维灯,钟世云. 水溶性单体对聚合物乳液在水泥浆体中稳定性的影响[J]. 《材料导报》期刊社, 2017, 31(24): 74-78.
[8] 李延安, 董海泉, 徐丽娜, 李蛟. 硅丙乳液包覆Mg(OH)2核壳结构纳米粒子的制备与表征*[J]. 《材料导报》期刊社, 2017, 31(18): 97-101.
[9] 肖俊华, 左迎峰, 吴义强, 刘文杰, 吴志平, 孟陶陶. 硅丙乳液对镁系无机胶黏剂性能和微结构的影响*[J]. 《材料导报》期刊社, 2017, 31(18): 49-54.
[10] 张元霞, 马建中, 徐群娜. 阳离子聚合物乳液的研究进展*[J]. 《材料导报》期刊社, 2017, 31(17): 61-67.
[1] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6] XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg98.5Zn0.5Y1 Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7] ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed