材料导报 2019, Vol. 33 Issue (Z2): 460-462
金属与金属基复合材料
|
铁素体不锈钢表面的拉丝缺陷
王冰
赫美斯(上海)磨料有限公司,上海 201712
Wire Drawing Defects on Ground Surface of Ferrite Stainless Steel
WANG Bing
Hermes Abrasives(Shanghai)Co., Ltd., Shanghai 201712
摘要 铁素体不锈钢表面拉丝时其表面会产生类似小凸点的缺陷,通过调整拉丝设备压力、不锈钢进给速度、砂带转速等,研究不锈钢表面加工参数对其表面质量的影响,并用EDX、SEM分析进行表征。结果表明:不锈钢表面的划痕缺陷不是由砂带上磨料颗粒不均、磨料脱落和加工设备里的其他杂质等造成的,而是由不锈钢表面本身的Cr粒子堆积球在砂带研磨时被锋利的碳化硅磨料划开所致。
关键词:
不锈钢拉丝
表面处理
表面缺陷
Abstract: The surface defects of ferric stainless steel are similar to small bumps during grinding. By adjusting the pressure of grinding equipment, the feed speed of stainless steel and the cutting speed of abrasive belt, the effect of surface processing parameters on the surface quality of stainless steel was studied, and characterized by EDX and SEM analysis. The results show that the defects of scratches on stainless steel surface is not caused by abrasive particles uneven on the abrasive belt, abrasive shedding and other impurities in the processing equipment, but caused by the sharp cut of silicon carbide abrasives on the surface of stainless steel when the Cr particles accumulated on the surface of stainless steel are grounded by abrasive belt.
Key words:
hairline for stainless steel
surface treatment
defect of surface
出版日期: 2019-11-25
发布日期: 2019-11-25
通讯作者:
wangbing1708@163.com
作者简介: 王冰,男,1983年7月15日生,硕士。主要研究方向:金属磨削及材料表面处理技术。
1 曹海山,孙小红.交通与建筑,2016(2),102. 2 朱则刚.特钢技术,2014(1),8. 3 应世凯.湖南农机,2010(3)37. 4 黄云,黄智,等.现代砂带磨削技术及工程应用,重庆大学出版社,2008. 5 黄云,朱派龙,等.砂带磨削技术及应用,重庆大学出版社,1993. 6 全洪军.典型孔精密研磨工艺与试验研究.硕士学位论文,辽宁科技大学,2016. 7 杜兆伟.镍基高温合金GH4169电解-磁力复合研磨加工试验研究.硕士学位论文,辽宁科技大学,2016.
[1]
Dongyong SI, Guangxu HUANG, Chuanxiang ZHANG, Baolin XING, Zehua CHEN, Liwei CHEN, Haoran ZHANG. Preparation and Electrochemical Performance of Humic Acid-based Graphitized Materials [J]. Materials Reports, 2018, 32(3): 368
-372
.
[2]
Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review [J]. Materials Reports, 2018, 32(3): 398
-404
.
[3]
Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage [J]. Materials Reports, 2018, 32(2): 282
-287
.
[4]
Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities [J]. Materials Reports, 2018, 32(2): 316
-321
.
[5]
Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support [J]. Materials Reports, 2018, 32(2): 219
-222
.
[6]
Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate [J]. Materials Reports, 2018, 32(2): 288
-294
.
[7]
WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing [J]. Materials Reports, 2017, 31(1): 64
-71
.
[8]
WANG Wenjin, WANG Keqiang, YE Shenjie, MIAO Weijun, CHEN Zhongren. Effect of Asymmetric Block Copolymer of PI-b-PB on Phase Morphology and Properties of IR/BR Blends [J]. Materials Reports, 2017, 31(2): 96
-100
.
[9]
HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber [J]. Materials Reports, 2017, 31(8): 21
-24
.
[10]
WU Tao, MAO Lili, WANG Haizeng. Preparation and Defluoridation Performance of Mg/Fe-LDHO/PES Membranous Adsorbent [J]. Materials Reports, 2017, 31(14): 26
-30
.
Viewed
Full text
Abstract
Cited
Shared
Discussed