医用镁合金的力学性能研究进展

材料导报

2019, Vol. 33

Issue (z1): 288-292

金属与金属基复合材料

医用镁合金的力学性能研究进展

刘印^1,2, 王昌², 于振涛², 盖晋阳^1,2, 曾德鹏^1,2

1 东北大学材料科学与工程学院,沈阳 110819
2 西北有色金属研究院,陕西省医用金属材料重点实验室,西安 710016

Review on Mechanical Properties of Medical Magnesium Alloys

LIU Yin^1,2, WANG Chang², YU Zhentao², GE Jinyang^1,2, ZENG Depeng^1,2

1 School of Materials Science and Engineering, Northeastern University, Shenyang 110819
2 Shaanxi Key Laboratory of Biomedical Metal Materials, Northwest Institute for Non-ferrous Metal Research, Xi’an 710016

摘要
参考文献
相关文章
推荐阅读
Metrics

下载:

全文 ( PDF ) ( 2403KB )
输出: BibTeX | EndNote (RIS)

摘要医疗与健康的需求对医用材料提出了更高的要求。镁合金因在人体内可降解并具有良好的生物相容性及与骨相近的弹性模量而有望成为新一代医用金属材料。然而镁合金作为植入物通常在不满服役期限前就已经失效,不能很好地满足植入物的力学性能要求。因此,本文首先综述了合金化、热处理和塑性变形三种改善力学性能的方法,然后指出目前镁合金亟待解决的问题,最后对医用镁合金的应用前景进行了展望。

	服务
	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	刘印
	王昌
	于振涛
	盖晋阳
	曾德鹏

关键词: 镁合金合金化热处理塑性变形力学性能

Abstract: Medical materials are needed to meet higher demands of medical and health requirements. Magnesium alloys are expected to be a new ge-neration of medical metal materials because of good biodegradability, biocompatibility and close elastic modulus to bone. However, magnesium alloys as an implant usually fails before it is out of service, and does not meet the mechanical properties of the implant. Therefore, this paper first reviews three methods to improve the mechanical properties: alloying, heat treatment and plastic deformation, then the problems to be solved in magnesium alloys are put forward. Finally, the application prospects of medical magnesium alloys are prospected.

Key words: agnesium alloys alloying heat treatment plastic deformation mechanical property

出版日期: 2019-05-25 发布日期: 2019-07-05

ZTFLH:

TG146

基金资助: 陕西省自然科学基金(2018JM5145);陕西省创新人才推进计划-青年科技新星项目(2018KJXX-026);陕西省国际合作基地项目(2017GHJD-014)

作者简介: 刘印,现为东北大学材料学院的硕士研究生,在于振涛教授的指导下进行研究。目前主要研究领域为医用镁合金的组织与性能。于振涛,从1987年一直在西北有色金属研究所工作,同时兼任东北大学和陕西科技大学兼职硕士生导师。历任助理工程师、工程师、高级工程师、教授级高级工程师。主要研究方向包括钛、镁等及其合金的新材料的加工和表面改性等,包括合金设计、熔炼和加工、微观结构和组织性能以及工程应用研究等。已经承担并参与国际、国家或者其他等级的40多个科学项目,获得国家或部委等级11项,并申请了80项国家发明专利,自1998年以来已发表了200多篇论文。最近开展了研发新型生物医用Ti,Mg,Zn合金材料等及其产品。中国生物材料学会常务委员会委员和其他材料委员会的成员。yzt@c-nin.com

引用本文:

刘印, 王昌, 于振涛, 盖晋阳, 曾德鹏. 医用镁合金的力学性能研究进展[J]. 材料导报, 2019, 33(z1): 288-292.
LIU Yin, WANG Chang, YU Zhentao, GE Jinyang, ZENG Depeng. Review on Mechanical Properties of Medical Magnesium Alloys. Materials Reports, 2019, 33(z1): 288-292.

链接本文:

http://www.mater-rep.com/CN/ 或 http://www.mater-rep.com/CN/Y2019/V33/Iz1/288

1 颜廷亭, 谭丽丽, 熊党生, 等. 材料导报,2008,22(1),110.
2 Sezer N, Evis Z, Kayhan S M, et al. Journal of Magnesium and Alloys,2018,6,23.
3 Ibrahim H, Esfahani S N, Poorganji B, et al. Materials Science & Engineering C Materials for Biological Applications,2017,70(1),870.
4 Erinc M, Sillekens W H, Mannens R, et al. In: Magnesium Technology 2009. San Francisco,CA,USA,2009.
5 周小淞, 何芳, 黄远,等. 医用镁钙合金的制备及力学性能研究,中国科技论文在线,北京2007.
6 宋奎. 生物医用镁锌合金微管显微组织和性能研究. 硕士学位论文, 扬州大学,2018.
7 吴琴. 医用镁锌锶钙合金性能及降解速率控制. 硕士学位论文,东北大学,2014.
8 Wang Y, Tie D, Guan R, et al. Journal of the Mechanical Behavior of Biomedical Materials,2018,77,47.
9 Cheng M, Chen J, Yan H, et al. Journal of Alloys & Compounds,2017,691,95.
10 刘军威, 彭晓东, 刘明朴, 等. 腐蚀与防护,2011,32(5),345.
11 李祯. 新型骨植入Mg-Zn-Zr-Sr合金及其体外耐蚀性的研究. 硕士学位论文, 天津理工大学,2016.
12 Gu X, Zheng Y, Cheng Y, et al. Biomaterials,2009,30(4),484.
13 Zhang X, Yuan G, Niu J, et al. Journal of the Mechanical Behavior of Biomedical Materials,2012,9,153.
14 Harandi S E, Idris M H, Jafari H. Materials & Design,2011,32(5),2596.
15 Rosalbino F, De N S, Scavino G, et al. Journal of Biomedical Materials Research Part A,2013,101A(3),704.
16 Gu X N, Xie X H, Li N, et al. Acta Biomaterial,2012,8(6),2360.
17 曾荣昌,崔蓝月,柯伟. 金属学报,2018,54(9),1215.
18 Zhao C Y, Pan F S, Zhao S, et al. Materials & Design,2015,70,60.
19 徐河, 刘静安, 谢水生.镁合金制备与加工技术.冶金工业出版社,2007.
20 Ibrahim H, Klarner A D, Poorganji B, et al. Journal of the Mechanical Behavior of Biomedical Materials,2017,69(Complete),203.
21 Maier P, Peters R, Mendis C L, et al. JOM,2016,68(4),1183.
22 Chen J, Tan L, Yang K. Bioactive Materials,2017,2(1),19.
23 Zhang Yuan, Li Jianxing, Li Jingyuan. Journal of the Mechanical Behavior of Biomedical Materials,2018,80,246.
24 Duraiswamy Rajenthirakumar, Nagarajan Srinivasan, Ramasamy Sridhar.Procedia Manufacturing,2018,15,1635.
25 Mohammadi D F,Jafari H.Transactions of Nonferrous Metals Society of China,2018,28(11),2199.
26 Lou Yan,Liu Xiao,He Jinsong, et al. Ultrasonics,2018,83,194.
27 Mahallawy N E,Ahmed D A, Akdesir M, et al. Materials Science & Engineering A,2017,680,47.
28 周世杰, 黄楠, 龚旭, 等.热加工工艺,2013,42(18),81.
29 Soumyaranjan Nayak, Bharat Bhushan, Jayaganthan R, et al. Journal of the Mechanical Behavior of Biomedical Materials,2016,59,57.
30 Li K,Injeti V,Trivedi P, et al. Journal of Materials Science & Technology,2018,34(2),311.
31 Li Nan,Zheng Yufeng. Journal of Materials Science & Technology,2013,29(6),489.
32 Yang Q, Xiao B L, Ma Z Y, et al. Scripta Materialia,2011,65(4),335.
33 Zheng F Y,Wu Y J ,Peng L M, et al. Journal of Magnesium and Alloys,2013,1(2),122.
34 Li J, Zhang D, Chai F. Materials Research Innovations,2014,18(S4),142.
35 Krzysztof Brya, Maciej Krystian, Jelena Horky, et al. Materials Science & Engineering A,2018,737,318.
36 Němec M,Gärtnerová V,Jäger A. Materials Characterization,2016,119,129.
37 Tomáš Krajňák, Peter Minárik, Jitka Stráská, et al. Journal of Alloys and Compounds,2017,123.282.
38 Peter Minárik, Robert Král, Jakub Cížek, et al. Acta Materialia,2016,107,83.
39 Yan Kai,Sun Jiapeng,Bai Jing, et al. Materials Science & Engineering A,2019,739,513.
40 张扬, 宋雷鹏, 陈晓阳, 等.中国专利,CN 108425051 A,2018.
41 张扬, 宋雷鹏, 陈晓阳, 等.中国专利,CN 108411173 A,2018.
42 Sun Jiapeng,Yang Zhenquan,Han Jing,et al.Materials Science & Engineering A,2018,734,485.

[1]	赵曦, 于振涛, 郑继明, 余森, 王昌. 合金元素影响镁合金弹性性能的第一性原理计算研究[J]. 材料导报, 2019, 33(z1): 293-296.
[2]	张长亮, 卢一平. 氮元素对Ti₂ZrHfV_0.5Mo_0.2高熵合金组织及力学性能的影响[J]. 材料导报, 2019, 33(z1): 329-331.
[3]	张哲轩, 周再峰, 山泉, 李祖来, 蒋业华, 张飞. 表面钨合金化对高铬铸铁组织和硬度的影响[J]. 材料导报, 2019, 33(z1): 362-365.
[4]	晁代义, 徐仁根, 孙有政, 赵巍, 吕正风, 程仁策, 邵文柱. 850 ℃时效处理对2205双相不锈钢组织与力学性能的影响[J]. 材料导报, 2019, 33(z1): 369-372.
[5]	王怡心, 马勤, 贾建刚, 高昌琦, 张瑄瑄. Half-Heusler热电材料性能优化策略及研究进展[J]. 材料导报, 2019, 33(z1): 403-407.
[6]	任秀秀, 朱一举, 赵省向, 韩仲熙, 姚李娜. 四种含能晶体微观力学性能与摩擦性能的关系[J]. 材料导报, 2019, 33(z1): 448-452.
[7]	薛晓武, 王新闻, 刘红波, 卿宁. 水性聚碳酸酯型聚氨酯的制备及性能[J]. 材料导报, 2019, 33(z1): 488-490.
[8]	郭建业, 赵英民, 张丽娟, 苏力军, 李文静, 杨洁颖. 高温可重复使用二氧化硅气凝胶复合材料性能研究[J]. 材料导报, 2019, 33(z1): 202-205.
[9]	杨康, 赵为平, 赵立杰, 梁宇, 薛继佳, 梅莉. 固化湿度对复合材料层合板力学性能的影响与分析[J]. 材料导报, 2019, 33(z1): 223-224.
[10]	平学龙, 符寒光, 孙淑婷. 激光熔覆制备硬质颗粒增强镍基合金复合涂层的研究进展[J]. 材料导报, 2019, 33(9): 1535-1540.
[11]	彭鹏, 汤爱涛, 佘加, 周世博, 潘复生. 超细晶镁合金的研究现状及展望[J]. 材料导报, 2019, 33(9): 1526-1534.
[12]	薛翠真, 申爱琴, 郭寅川. 基于孔结构参数的掺CWCPM混凝土抗压强度预测模型的建立[J]. 材料导报, 2019, 33(8): 1348-1353.
[13]	陈琛辉, 蒋璐瑶, 刘成龙, 黄伟九, 郭勇义, 胥桥梁. 搅拌摩擦加工细晶TA2工业纯钛晶粒长大规律[J]. 材料导报, 2019, 33(8): 1367-1370.
[14]	王应武, 左孝青, 冉松江, 孔德昊. TiB₂含量及T6热处理对原位TiB₂/ZL111复合材料显微组织和硬度的影响[J]. 材料导报, 2019, 33(8): 1371-1375.
[15]	时博, 王金辉, 魏福安. 金属玻璃自由体积理论的研究概述[J]. 材料导报, 2019, 33(7): 1221-1226.

[1]	Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2]	Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3]	Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4]	Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5]	Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6]	XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg_98.5Zn_0.5Y₁ Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7]	ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8]	WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9]	HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10]	YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .

Viewed

Full text

Abstract

Cited

Shared

Discussed