Please wait a minute...
材料导报  2019, Vol. 33 Issue (Z2): 402-405    
  金属与金属基复合材料 |
Cu元素含量对Al-Zn-Mg-Cu系合金析出行为的影响
晁代义1, 孙有政1, 刘晓滕1, 李兴东1, 李维建2, 吕正风1, 程仁策1
1 山东南山铝业股份有限公司, 国家铝合金压力加工工程技术研究中心,龙口 265713;
2 烟台大学核装备与核工程学院,烟台 264005
Effect of Cu Content on Precipitation Behavior of Al-Zn-Mg-Cu Aluminum Alloy
CHAO Daiyi1, SUN Youzheng1, LIU Xiaoteng1, LI Xingdong1, LI Weijian2, LYU Zhengfeng1, CHENG Rence1
1 National Engineering Research center for Plastic Working of Aluminium Alloys, Shandong Nanshan Aluminum Co., Ltd., Longkou 265713;
2 College of Nuclear Equipment and Nuclear Engineering, Yantai University, Yantai 264005
下载:  全 文 ( PDF ) ( 2056KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 采用热力学模拟手段研究了Al-Zn-Mg-Cu系合金中不同Cu含量对析出相GP区及η′相的析出规律。结果表明, GP区及η′相中含部分Cu元素;在120 ℃和160 ℃时效时,随Cu元素含量从1.9%(质量分数, 下同)增加到2.5%,GP区含量有所降低分别从2.65%和1.11%降低到2.60%和1.02%,而η′相含量有所增加, 分别从6.71%和6.52%增加到7.25%和7.07%。当强化相η′相含量达到6.5%时所用时间随Cu含量的增加而减少,当Cu含量从1.9%增加到2.5%时,120 ℃和160 ℃所用时间分别从23 h和5 h缩短到16 h和2.8 h。不同Cu含量下GP区和η′相的鼻尖温度区间分别为150 ℃和330 ℃,基本保持不变,临界冷却速率基本保持在16 ℃/s,说明Cu含量对合金的淬火敏感性影响较小。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
晁代义
孙有政
刘晓滕
李兴东
李维建
吕正风
程仁策
关键词:  热力学模拟  Cu含量  时效温度  淬火敏感性  临界冷却速率    
Abstract: The effects of Cu content on precipitation behavior of GP area and η′ phase of Al-Zn-Mg-Cu aluminum alloy was investigated by using the aluminum alloy module in thermodynamic simulation software in detail. The results show that the content of some Cu element was in GP area and η′ phase. Under aging temperature of 120 ℃ and 160 ℃, with the increase of Cu content from 1.9% to 2.5%, the content of GP area decreased from 2.65% and 1.11% to 2.60% and 1.02% respectively. While the content of η′ phase decreased from 6.71% and 6.52% to 7.25% and 7.07% respectively. The used time of η′ phase content reaching 6.5wt% decreased with the increase of Cu content. The time from 23 h and 5 h droped down to 16 h and 2.8 h with the increase of Cu content at the aging temperature 120 ℃ and 160 ℃, respectively. The nose temperature kept at 150 ℃ of GP area and 330 ℃ of η′ phase with the increasing of Cu content, as well as the critical cooling ratio kept at 16 ℃/s. In other words, the content of Cu have a little effect on quenching sensitivity.
Key words:  thermodynamic simulation    Cu content    aging temperature    quenching sensitivity    critical cooling ratio
               出版日期:  2019-11-25      发布日期:  2019-11-25
ZTFLH:  TG142.71  
通讯作者:  cdy19861226@163.com   
作者简介:  晁代义,2013年6月毕业于烟台大学,获得工学硕士学位。2013年9月到2017年3月于哈尔滨工业大学材料学院攻读博士学位。主要从事不锈钢及高强铝合金热处理及变形工艺研究以及金属材料失效分析。目前担任中国机械工程协会失效分析分会失效分析专家。
李维建,博士、讲师,2019年8月至今,任职烟台大学核装备与核工程学院,主要从事金属材料界面第一性原理研究及工艺性能研究。
引用本文:    
晁代义, 孙有政, 刘晓滕, 李兴东, 李维建, 吕正风, 程仁策. Cu元素含量对Al-Zn-Mg-Cu系合金析出行为的影响[J]. 材料导报, 2019, 33(Z2): 402-405.
CHAO Daiyi, SUN Youzheng, LIU Xiaoteng, LI Xingdong, LI Weijian, LYU Zhengfeng, CHENG Rence. Effect of Cu Content on Precipitation Behavior of Al-Zn-Mg-Cu Aluminum Alloy. Materials Reports, 2019, 33(Z2): 402-405.
链接本文:  
http://www.mater-rep.com/CN/  或          http://www.mater-rep.com/CN/Y2019/V33/IZ2/402
1 Dursun T D, Soutis C. Materials & Design,2014,56,862.
2 杜爱华,龙晋明,裴和中.中国腐蚀与防护学报,2009,28(4),251.
3 Wang S S, Jiang J T, Zhen L. Journal of the Electrochemical Society,2015,162,C150.
4 Sha G, Cerezo A. Acta Materialia,2004,52(15),4503.
5 Deschamps A, Brechet Y, Livet F. Materials Science and Technology,1999,15(9),993.
6 Marlaud T, Deschamps A, Bely F. Acta Materialia,2010,58(14),4814.
7 Gupta R K, Deschamps A. Journal of the Electrochemical Society,2012,159(11),C492.
8 Conserva M, Fiorini P. Metallurgical Transactions,1973,4(3),857.
9 谢优华,杨守杰,戴圣龙.材料导报,2002,16(5),8.
10 方华婵,陈康华,巢宏,等.粉末冶金材料科学与工程,2009,14(6),352.
11 Wagner J A, Shenoy R N. Metallurgical Transactions A,1991,22(11),2809.
12 黎彦希,陈康华,陈送义.粉末冶金材料科学与工程,2014,6(5),727.
13 Yu Jingjing. Journal of Phase Equilibria and Diffusion,2011,32(4),350.
[1] 晁代义, 孙有政, 刘晓滕, 李兴东, 李维建, 吕正风, 程仁策. Zn/Mg比及时效温度对Al-Zn-Mg-Cu系合金析出行为的影响[J]. 材料导报, 2019, 33(Z2): 398-401.
[2] 肖靖,易幼平,崔金栋,黄始全. 7085铝合金的淬火敏感性[J]. 《材料导报》期刊社, 2018, 32(12): 1998-2002.
[3] 江道, 易幼平, 黄始全. LD7铝合金淬火敏感性及相变动力学规律*[J]. 《材料导报》期刊社, 2017, 31(12): 140-144.
[4] 董非,易幼平,黄始全,张玉勋,. 2A14铝合金TTT曲线及其淬火敏感性*[J]. 材料导报编辑部, 2017, 31(10): 77-81.
[1] Dongyong SI, Guangxu HUANG, Chuanxiang ZHANG, Baolin XING, Zehua CHEN, Liwei CHEN, Haoran ZHANG. Preparation and Electrochemical Performance of Humic Acid-based Graphitized Materials[J]. Materials Reports, 2018, 32(3): 368 -372 .
[2] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[3] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[4] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[5] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[6] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[7] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[8] WANG Wenjin, WANG Keqiang, YE Shenjie, MIAO Weijun, CHEN Zhongren. Effect of Asymmetric Block Copolymer of PI-b-PB on Phase Morphology and Properties of IR/BR Blends[J]. Materials Reports, 2017, 31(2): 96 -100 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] WU Tao, MAO Lili, WANG Haizeng. Preparation and Defluoridation Performance of Mg/Fe-LDHO/PES Membranous Adsorbent[J]. Materials Reports, 2017, 31(14): 26 -30 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed