时效处理对4A双相不锈钢σ相析出及性能的影响*

doi:10.11896/j.issn.1005-023X.2017.016.016

《材料导报》期刊社

2017, Vol. 31

Issue (16): 76-80 https://doi.org/10.11896/j.issn.1005-023X.2017.016.016

材料研究

时效处理对4A双相不锈钢σ相析出及性能的影响^*

卢盼盼¹, 王爱琴¹, 谢敬佩², 王文焱¹

1 河南科技大学材料科学与工程学院, 洛阳 471023;
2 河南科技大学材料科学与工程学院,有色金属共性技术河南省协同创新中心, 洛阳 471023

Effect of Aging on σ Phase Precipitation and Properties of 4A Duplex Stainless Steel

LU Panpan¹, WANG Aiqin¹, XIE Jingpei², WANG Wenyan¹

1 College of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471023;
2 Collaborative Innovation Center of Nonferrous Metals of Henan Province, School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471023

摘要
参考文献
相关文章
推荐阅读
Metrics

下载:

全文 ( PDF ) ( 2207KB )
输出: BibTeX | EndNote (RIS)

摘要对固溶处理后的4A双相不锈钢(DSS4A)进行不同温度(750～900 ℃)的等温时效处理,利用OM观测各个时效温度下σ相的析出行为,重点观测了σ相在850 ℃时效不同时间(1 h、2 h和4 h)的析出过程,并通过SEM、EDS和TEM等检测手段对850 ℃、4 h时效处理后的σ相析出形貌进行分析,揭示了σ相的析出特征及形成机理。最后对时效条件下4A双相不锈钢的力学性能和耐蚀性能也进行了相应研究。结果表明:σ相富Cr、Mo而贫Ni,属于四方结构,由高温铁素体分解而成;σ相析出量随时效温度的升高先增加后降低并在850 ℃时达到峰值,同一温度下时效时间越长,σ相析出越多;σ相使材料硬度提高,但材料抗拉强度、冲击韧性和耐腐蚀性整体呈下降趋势,其中冲击韧性对σ相析出尤为敏感。

	服务
	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	卢盼盼
	王爱琴
	谢敬佩
	王文焱

关键词: 4A双相不锈钢时效处理 σ相性能

Abstract: The effect of aging treatment on precipitation behavior of σ phase of 4A duplex stainless steel after solution treatment was observed by OM, and the precipitation process of σ phase at 850 ℃ for different time was analyzed. In order to investigate the precipitation characteristics and the mechanisms of σ phase, the morphology of the sample by aging for 4 hours was analyzed by SEM, EDS and TEM. Finally, the mechanical properties and corrosion resistance of 4A duplex stainless steel were also studied. The results show that σ phase is rich in Cr, Mo but Ni-depleted, its crystal structure is tetragonal and it is formed by the decomposition of δ; σ phase precipitation increased first and then decreased with the increase of aging temperature, and it reaches a peak at 850 ℃. The σ phase precipitation is more, when the aging time is longer under the same temperature; σ phase causes higher hardness of the material, but generally declining tensile strength, impact toughness and corrosion resistance, among which the impact toughness is particularly sensitive to the σ phase precipitation.

Key words: 4A duplex stainless steel aging treatment σ phase property

出版日期: 2017-08-25 发布日期: 2018-05-07

ZTFLH:

TG142.71

基金资助: 河南省产学研合作项目(132107000053)

通讯作者: 王爱琴:通讯作者,女,博士,教授,研究方向为先进复合材料 Tel:0379-64231269 E-mail:aiqin_wang888@163.com

作者简介: 卢盼盼:男,1988年生,硕士研究生,主要从事双相不锈钢研究 E-mail:hkdcailiao@163.com

引用本文:

卢盼盼, 王爱琴, 谢敬佩, 王文焱. 时效处理对4A双相不锈钢σ相析出及性能的影响^*[J]. 《材料导报》期刊社, 2017, 31(16): 76-80.
LU Panpan, WANG Aiqin, XIE Jingpei, WANG Wenyan. Effect of Aging on σ Phase Precipitation and Properties of 4A Duplex Stainless Steel. Materials Reports, 2017, 31(16): 76-80.

链接本文:

https://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2017.016.016 或 https://www.mater-rep.com/CN/Y2017/V31/I16/76

1 吴玖. 双相不锈钢[M]. 北京: 冶金工业出版社,2000.
2 Feng H, Zhou X Y, Liu H, et al. Development and trend of hyper duplex stainless steels[J]. J Iron Steel Res, 2015,27(4):1(in Chinese).
丰涵, 周晓玉, 刘虎,等. 特超级双相不锈钢的发展现状及趋势[J]. 钢铁研究学报,2015,27(4):1.
3 Jimenez J A, Carsi M, Ruano O A, et al. Characterization of a delta/gamma duplex stainless steel[J]. J Mater Sci,2000,35(4):907.
4 Hussain E A M, Robinson M J. Erosion-corrosion of 2205 duplex stainless steel in flowing seawater containing sand particles[J]. Corros Sci,2007,49(4):1737.
5 Ghosh S K, Mondal S. High temperature ageing behaviour of a duplex stainless steel[J]. Mater Character, 2008, 59(12):1776.
6 Huang C S, Shih C C. Effects of nitrogen and high temperature aging on σ phase precipitation of duplex stainless steel[J]. Mater Sci Eng A,2005,402(1-2):66.
7 Chen T H, Yang J R. Effects of solution treatment and continuous cooling on σ-phase precipitation in a 2205 duplex stainless steel[J]. Mater Sci Eng A, 2001,311(1-2):28.
8 Wei Bin, Bai Zhenquan, Yin Chengxian, et al. Effects of solid solution treatment on pitting corrosion behavior of 2205 duplex stainless steel[J].Trans Mater Heat Treatment,2009,30(4):73(in Chinese).
魏斌, 白真权, 尹成先,等. 固溶处理对2205双相不锈钢点蚀性能的影响[J]. 材料热处理学报,2009,30(4):73.
9 Sato Y S, Kokawa H. Preferential precipitation site of sigma phase in duplex stainless steel weld metal[J]. Scr Mater,1999,40(6):659.
10 Bin Yuanhong, Li Peifen, Li Zhizheng, et al. Precipitation of σ-phase and its effect on impact toughness of a duplex stainless steel solution-treated at different temperatures[J]. Trans Mater Heat Treatment,2013,34(8):136(in Chinese).
宾远红, 李培芬, 李志铮,等. 不同固溶温度对双相不锈钢σ相析出及冲击韧性的影响[J]. 材料热处理学报,2013,34(8):136.
11 Ding X P, Liu X, He Y L, et al. Study of precipitation evolution in 2205 DSS during aging treatment and its effect on impact toughness[J]. Iron Steel,2010,45(6):84(in Chinese).
丁秀平, 刘雄, 何燕霖,等. 时效条件下2205双相不锈钢中的析出相分析及其对冲击性能的影响[J]. 钢铁,2010,45(6):84.
12 Luo Z Y, Li J Y. Precipitation behavior of σ phase in UNS S32760 super duplex stainless steel[J]. Trans Mater Heat Treatment,2015,36(4):110(in Chinese).
罗照银, 李静媛. S32760超级双相不锈钢中σ相的析出规律[J]. 材料热处理学报,2015,36(4):110.
13 Liu X, He Y L, Ding X P, et al. Effect of high temperature aging on σ-phase precipitation in a 2205 duplex stainless steel[J]. Trans Mater Heat Treatment,2010,31(3):48(in Chinese).
刘雄, 何燕霖, 丁秀平,等. 高温时效对2205双相不锈钢中σ相析出行为的影响[J]. 材料热处理学报,2010,31(3):48.
14 Maehara Y, Koike M, Fujino N, et al. Precipitation of σ phase in a 25Cr-7Ni-3Mo duplex phase stainless steel[J]. Trans Iron Steel Institute Jpn,1983,23(3):240.
15 Zhao Z Y, Xu L, Li G P, et al. Precipitation behavior of σ-phase and its effect on microstructure and properties of a super duplex stainless steel[J].Trans Mater Heat Treatment,2010,31(10):75(in Chinese).
赵志毅, 徐林, 李国平,等. 超级双相不锈钢σ相析出及对组织性能的影响[J]. 材料热处理学报,2010,31(10):75.
16 Xiang H L, Liu D, Ruan F R, et al. Effects of precipitation for aging on mechanical and corrosion resistance properties of cast 2507 super duplex stainless steel [J]. Acta Metall Sin,2010,46(8):941(in Chinese).
向红亮, 刘东, 阮方如,等. 时效析出相对铸造2507超级双相不锈钢力学及耐蚀性能的影响[J]. 金属学报,2010,46(8):941.
17 Pohl M, Storz O, Glogowski T. Effect of intermetallic precipitations on the properties of duplex stainless steel[J]. Mater Character,2007,58(1):65.
18 Liu X, Ding X P, He Y L, et al. Effect of aging treatment on σ phase precipiation and toughness property in a 2205 duplex stainless steel [J]. Shanghai Metals,2010,32(1):39(in Chinese).
刘雄, 丁秀平, 何燕霖,等. 高温时效对2205双相不锈钢冲击韧性的影响[J]. 上海金属,2010,32(1):39.

[1]	童汇, 谢建龙, 张志谋, 郭忻, 喻万景, 郭学益, 黄承焕. 富锂锰基正极材料研究进展[J]. 材料导报, 2025, 39(3): 23080074-18.
[2]	程东海, 张夫庭, 陶玄宇, 余超, 龚浩, 李海涛, 王德, 熊震宇. 稀土元素对钛合金激光焊接头组织及性能的影响[J]. 材料导报, 2025, 39(3): 23060020-5.
[3]	温强, 李向成, 花银群, 关庆丰, 蔡杰. 强流脉冲电子束表面改性技术及其在热障涂层改性中的研究进展[J]. 材料导报, 2025, 39(3): 23090070-11.
[4]	薛赞, 晋玺, 毛周朱, 兰爱东, 王大雨, 乔珺威. 热机械处理提高Cr₄₇Ni₃₃Co₁₀Fe₁₀多组元共晶合金力学性能[J]. 材料导报, 2025, 39(3): 23120100-6.
[5]	卞宏友, 柳金生, 刘伟军, 张广泰, 姚佳彬, 邢飞. 激光沉积修复GH738/K417G合金时效热处理组织性能分析[J]. 材料导报, 2025, 39(3): 23110265-6.
[6]	刘晓楠, 张春晓, 王世合, 张高展, 毛继泽, 曹少华, 刘国强. 养护制度对添加纳米SiO₂超高性能混凝土动静态力学性能的影响[J]. 材料导报, 2025, 39(2): 23070188-7.
[7]	王艳, 李伊岚, 杨子凡, 常天风, 孙琳琳. OPC-SAC复合胶凝体系对超高性能混凝土性能的影响[J]. 材料导报, 2025, 39(2): 23120218-7.
[8]	杨淑雁, 徐宁阳. 多因素复合环境下钢筋与混凝土黏结性能研究进展[J]. 材料导报, 2025, 39(2): 23100224-10.
[9]	景宏君, 张超伟, 高萌, 丁仁红, 李毅民, 康明珂, 周子涵, 朱韶峰. 骨架密实型水泥稳定煤矸石级配设计与性能研究[J]. 材料导报, 2025, 39(2): 22040252-7.
[10]	周祎伟, 段海涛, 李健, 马利欣, 李文轩, 尤锦鸿, 贾丹. 外加磁场对摩擦副材料摩擦磨损及抗腐蚀性能影响的研究进展[J]. 材料导报, 2025, 39(2): 23110090-19.
[11]	曹雷刚, 侯鹏宇, 杨越, 蒙毅, 刘园, 崔岩. AlCoCrFeNi_x高熵合金高温热处理微观组织演变及力学性能[J]. 材料导报, 2025, 39(2): 23120247-7.
[12]	李朋娟, 邹振羽, 黄鹏飞, 金鑫, 吴晓雨, 李晓丽. N/O/P共掺杂三聚氰胺基多孔碳材料的制备及储锌性能研究[J]. 材料导报, 2025, 39(2): 23100113-7.
[13]	裴海华, 赵建伟, 郑家桢, 张贵才, 张菅, 蒋平. 改性纳米锂皂石强化高温泡沫调驱性能研究[J]. 材料导报, 2025, 39(2): 22110070-5.
[14]	赵佳薇, 陈浩霖, 罗倪, 刘振国. 卷对卷技术制备钙钛矿太阳能电池的研究进展[J]. 材料导报, 2025, 39(1): 24030057-17.
[15]	王丕, 宋琛, 董东东, 曾德长, 刘太楷, 文魁, 毛杰, 刘敏. 多孔Fe24Cr金属支撑体厚度对SOFC性能的影响[J]. 材料导报, 2025, 39(1): 23110193-7.

[1]	Huanchun WU, Fei XUE, Chengtao LI, Kewei FANG, Bin YANG, Xiping SONG. Fatigue Crack Initiation Behaviors of Nuclear Power Plant Main Pipe Stainless Steel in Water with High Temperature and High Pressure[J]. Materials Reports, 2018, 32(3): 373 -377 .
[2]	Miaomiao ZHANG,Xuyan LIU,Wei QIAN. Research Development of Polypyrrole Electrode Materials in Supercapacitors[J]. Materials Reports, 2018, 32(3): 378 -383 .
[3]	Congshuo ZHAO,Zhiguo XING,Haidou WANG,Guolu LI,Zhe LIU. Advances in Laser Cladding on the Surface of Iron Carbon Alloy Matrix[J]. Materials Reports, 2018, 32(3): 418 -426 .
[4]	Huaibin DONG,Changqing LI,Xiahui ZOU. Research Progress of Orientation and Alignment of Carbon Nanotubes in Polymer Implemented by Applying Electric Field[J]. Materials Reports, 2018, 32(3): 427 -433 .
[5]	Xiaoyu ZHANG,Min XU,Shengzhu CAO. Research Progress on Interfacial Modification of Diamond/Copper Composites with High Thermal Conductivity[J]. Materials Reports, 2018, 32(3): 443 -452 .
[6]	Anmin LI,Junzuo SHI,Mingkuan XIE. Research Progress on Mechanical Properties of High Entropy Alloys[J]. Materials Reports, 2018, 32(3): 461 -466 .
[7]	Qingqing DING,Qian YU,Jixue LI,Ze ZHANG. Research Progresses of Rhenium Effect in Nickel Based Superalloys[J]. Materials Reports, 2018, 32(1): 110 -115 .
[8]	Yaxiong GUO,Qibin LIU,Xiaojuan SHANG,Peng XU,Fang ZHOU. Structure and Phase Transition in CoCrFeNi-M High-entropy Alloys Systems[J]. Materials Reports, 2018, 32(1): 122 -127 .
[9]	Changsai LIU,Yujiang WANG,Zhongqi SHENG,Shicheng WEI,Yi LIANG,Yuebin LI,Bo WANG. State-of-arts and Perspectives of Crankshaft Repair and Remanufacture[J]. Materials Reports, 2018, 32(1): 141 -148 .
[10]	Xia WANG,Liping AN,Xiaotao ZHANG,Ximing WANG. Progress in Application of Porous Materials in VOCs Adsorption During Wood Drying[J]. Materials Reports, 2018, 32(1): 93 -101 .

Viewed

Full text

Abstract

Cited

Shared

Discussed