粉体粒径对数字光处理3D打印金刚石复合材料性能的影响

doi:10.11896/cldb.21120211

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (6360KB)
Export: BibTeX | EndNote (RIS)

Abstract Based on the principle of digital light processing (DLP)3D printing technology, the rheological properties and curing characteristics of diamond-resin slurries with various diamond particle sizes were systematically investigated, as well as the mechanical properties of the diamond-resin composites prepared by DLP. The results show that increasing the particle size can reduce the specific surface area and surface energy, effectively reduce the viscosity of the diamond-resin slurry and improve the fluidity of the slurry during the DLP printing process. Combined with the Beer-Lambert model equation, it was found that, under the same exposure energy, slurry with larger diamond particle size possess a higher cure depth, which is beneficial to the interlayer bonding strength of the composites made therefrom. However, the excess cure width also increases with the particle sizes, leading to a decrease in printing accuracy. Results from the mechanical performance test of the diamond-resin composite indicate that increasing the particle size improves the shore hardness of the composite little, whereas it is beneficial to improve the fle-xural strength and elastic modulus of the composite. In this work, diamond-resin composites with different particle sizes of diamond powder were prepared via DLP 3D printing technology, providing an experimental reference for the fabrication of ultraviolet-curable resin-bonded diamond tools by stereolithography 3D printing in the future.

Key words： additive manufacturing digital light process (DLP) diamond-resin composite curing characteristic mechanical property

Published: 25 June 2023 Online: 2023-06-20

CLC number:

TB332

Fund:Frontier and Key Technology Innovation Project of Guangdong Province (2017B090911006), Jihua Laboratory Project (X190061UZ190), and Foshan Science and Technology Innovation Team Project (FS0AA-KJ919-4402-0023).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	YANG Wenxin
	MENG Xiaoyan
	DENG Xin

Cite this article:

YANG Wenxin,MENG Xiaoyan,DENG Xin. Effect of Powder Particle Size on the Properties of Diamond Composites Fabricated by Digital Light Processing 3D Printing[J]. Materials Reports, 2023, 37(12): 21120211-6.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.21120211 OR http://www.mater-rep.com/EN/Y2023/V37/I12/21120211

1 Tönshoff H K, Hillmann-apmann H, Asche J. Diamond and Related Materials, 2002, 11, 736.
2 Lavrinenko V I. Journal of Superhard Materials, 2018, 40, 348.
3 Deja M, Zielinski D, Kadir A Z A, et al. Materials (Basel), 2021, 14(5), 1318.
4 Duan W Y, Yin Y H, Xue Q H, et al. Bulletin of the Chinese Ceramic Society, 2015, 34(3), 808 (in Chinese).
段文远, 尹育航, 薛群虎, 等. 硅酸盐通报, 2015, 34(3), 808.
5 Gao C, Zhu F, Liu M Y, et al. Diamond and Abrasives Engineering, 2014, 34(1), 64 (in Chinese).
高翀, 朱峰, 刘明耀, 等. 金刚石与磨料磨具工程, 2014, 34(1), 64.
6 Peng W, Yao C Y, Lv X, et al. Key Engineering Materials, 2007, 329, 489.
7 Peng W, Liu F Q, Yao C Y. Advanced Materials Research, 2009, 832, 69.
8 Huang Q, Guo L, Marinescu I. Procedia Manufacturing, 2016, 5, 259.
9 Guo L, Huang Q, Marinescu I. Machining Science & Technology, 2017, 21, 223.
10 Quan H, Zhang T, Xu H, et al. Bioactive Materials, 2020, 5, 110.
11 Du Z J, Zhang F L, Xu Q S, et al. Ceramics International, 2019, 45, 20873.
12 Yang Z, Zhang M, Zhang Z, et al. Materials & Design, 2016, 104, 292.
13 Tian C, Li X, Chen Z, et al. Journal of Manufacturing Processes, 2020, 54, 38.
14 Tian C, Li X, Zhang S, et al. The International Journal of Advanced Manufacturing Technology, 2018, 100, 1451.
15 Qiu Y, Huang H, Xu X. The International Journal of Advanced Manufacturing Technology, 2018, 97, 3873.
16 Guo L, Huang Q, Marinescu I. Machining Science and Technology, 2017, 21, 223.
17 Zhang Y H, Huang J L, Song Y Y, et al. Diamond and Abrasive Engineering, 2021, 41(3), 8 (in Chinese).
张云鹤, 黄景銮, 宋运运, 等. 金刚石与磨料磨具工程, 2021, 41(3), 8.
18 Pagac M, Hajnys J, Ma Q P, et al. Polymers (Basel), 2021, 13(4), 598.
19 Chen Z, Li Z, Li J, et al. Journal of the European Ceramic Society, 2019, 39, 661.
20 Meng X Y, Yang W X, Deng X. Diamond and Related Materials, 2021, 120, 108715.
21 Wozniak M, Hazan Y D, Graule T, et al. Journal of the European Ceramic Society, 2011, 31, 2221.
22 Hingorani H, Zhang Y F, Zhang B, et al. International Journal of Smart & Nano Materials, 2019, 10, 225.
23 Chen Z, Li J, Liu C, et al. Ceramics International, 2019, 45, 11549.
24 Li X B, Zhong H, Zhang J X, et al. Journal of Inorganic Materials, 2019, 35, 231.
25 Konijn B J, Sanderink O B J, Kruyt N P. Powder Technology, 2014, 266, 61.
26 Ding G, He R, Zhang K, et al. Journal of the American Ceramic Society, 2019, 102, 7198.
27 Shan D M, Morris J, Plaisted T A, et al. Additive Manufacturing, 2021, 37, 101736.
28 Gentry S P, Halloran J W. Journal of the European Ceramic Society, 2015, 35, 1895.
29 Shen M, Zhao W, Xing B, et al. Ceramics International, 2020, 46, 24379.
30 Hu C, Chen Y, Yang T, et al. Ceramics International, 2021, 47, 12442.
31 Griffith M L, Halloran J W. Journal of Applied Physics, 1997, 81, 2538.
32 Zheng T, Wang W, Sun J, et al. Ceramics International, 2020, 46, 8682.
33 Sun C, Zhang X. Journal of Applied Physics, 2002, 92, 4796.
34 Yang N N, Liu H R, He L Q, et al. Journal of Longdong University, 2021, 32(5), 5 (in Chinese).
杨娜娜, 刘浩锐, 贺立群, 等. 陇东学院学报, 2021, 32(5), 5.