选区激光熔化制备颗粒增强金属基复合材料的研究进展

doi:10.11896/cldb.20040170

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (11873KB)
Export: BibTeX | EndNote (RIS)

Abstract Selective laser melting is an additive manufacturing method which uses focused high-energy laser beam to melt powder and fabricates parts layer by layer. Selective laser melting can directly fabricate complex structural parts and realize near net shape. Selective laser melting has attracted more and more attentions due to its special advantages in control of shape and property of particle reinforced metal matrix composites by powder pre-mixing or in-situ reaction.
In this paper, research progress on preparation of particle reinforced metal matrix composites by selective laser melting is reviewed. Based on summarization of main results and problems in this field, research directions and development trends of particle reinforced metal matrix composites fabricated by selective laser melting are prospected. It is confirmed that the molten pool formed by focused laser with high temperature and short solidification time is far away from the equilibrium state, resulting in complex solidification process and violent metallurgical reaction between the reinforced particles and the matrix. The reinforced particles are easy to melt, decompose or dissolve into matrix during selective laser melting process, leading to characteristics changes of matrixes. Eventually, the microstructure and properties of the composites after forming are significantly influenced. Apart from composition, morphology, size and volume fraction of the particle reinforcements, the properties of composites are also affected by laser power, scanning speed, scanning spacing, powder layer thickness, forming atmosphere and other process parameters. Since interaction between powder properties and process parameters is complex,so it is extremely important to investigate the interaction between process parameters and powder characteristics and systematically study the influence of particle reinforcement characteristics and forming process parameters on the macro morphology, density, defects, microstructure and properties of the composites. Those studies are the basis for microstructure design and property control of composites.

Key words： selective laser melting particle reinforced metal matrix composites process parameter

Published: 25 January 2022 Online: 2022-01-26

CLC number:

TB331

Fund:National Natural Science Foundation of China(51961017), the Key Project of Yunnan Fundamental Research (202101AS070017).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	TENG Baoren
	LI Zhenhua
	LI Huaiyang
	YANG Rui
	SHEN Jibiao

Cite this article:

TENG Baoren,LI Zhenhua,LI Huaiyang, et al. Research Progress on Preparation of Particle Reinforced Metal Matrix Composites by Selective Laser Melting[J]. Materials Reports, 2022, 36(2): 20040170-6.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.20040170 OR http://www.mater-rep.com/EN/Y2022/V36/I2/20040170

1 Nie X W,Liu R. Recent Patents on Materials Science,2012,5(2),149.
2 Si C R,Zhang X J,Wang J B. Jorunal of Functional Materials,2015,46(1),01001 (in Chinese).
司朝润,张贤杰,王俊彪.功能材料,2015,46(1),01001.
3 Wang H Y,Li C,Li Z G,et al. Acta Metallurgica Sinica,2019,55(6),683(in Chinese).
王慧远,李超,李志刚,等.金属学报,2019,55(6),683.
4 Li J G,Laghari R. International Journal of Advanced Manufacturing Technology,2019,100,2929.
5 Li H L,Jia D C,Yang Z H,et al. Materials Science and Technology,2019,27(2),1(in Chinese).
李海亮,贾德昌,杨治华,等.材料科学与工艺,2019,27(2),1.
6 Yang Y Q,Chen J,Song C H,et al. Laser & Optoelectronics Progress,2018,55(1),9 (in Chinese).
杨永强,陈杰,宋长辉,等.激光与光电子学进展,2018,55(1),9.
7 Tian J,Huang Z H,Qi W J,et al. Materials Reports,2017,31(Z1),90 (in Chinese).
田杰,黄正华,戚文军,等.材料导报,2017,31(Z1),90.
8 Pavlov M,Doubenskaia M,Smurov I. Physics Procedia,2010,5,523.
9 Wang D, Yang Y Q. In: The 5th National Conference on Rapid Prototyping and Manufacturing. Xi'an, 2011,pp. 58
王迪,杨永强.第五届全国快速成形与制造学术会议.西安,2011,pp. 58.
10 Zhu Y T,Du K P,Shen J,et al. Thermal Spray Technology,2017,9(2),35 (in Chinese).
朱云天,杜开平,沈婕,等.热喷涂技术,2017,9(2),35.
11 Duan W,Zhao Z,Ji H W,et al. Materials Reports B:Research Papers,2019,33(10),1685 (in Chinese).
段伟,赵哲,吉红伟,等.材料导报:研究篇,2019,33(10),1685.
12 Yu W H,Sing S L,Chua C K,et al. Progress in Materials Science,2019,104,330.
13 Shen Q,Yu S,Niu J L,et al. Materials Reports,2019,33(Z1),278 (in Chinese).
申琦,余森,牛金龙,等.材料导报,2019,33(Z1),278.
14 Zhang S S.Preparation and properties of TiC particle reinforced 316L stainless steel composites by selective laser melting.Master's Thesis,Harbin Engineering University,China, 2019 (in Chinese).
张莎莎.TiC颗粒增强316L不锈钢复合材料选区激光熔化制备及性能研究.硕士学位论文,哈尔滨工程大学,2019.
15 Cheng L Y.Selective laser melting fabrication of stainless steel and nano hydroxyapatite biocomposites.Master's Thesis,Huazhong University of Science and Technology,China, 2014 (in Chinese).
程灵钰.SLM制备不锈钢与纳米羟基磷灰石复合材料研究.硕士学位论文,华中科技大学,2014.
16 Hu H,Zhou Y,Wen S F,et al. Chinese Journal of Lasers,2018,45(12),1202010-1 (in Chinese).
胡辉,周燕,文世峰,等.中国激光,2018,45(12),1202010-1.
17 Tan C L.Selective laser melting of maraging steel and its composite, gra-dient materials.Ph.D. Thesis,South China University of Technology,China, 2019 (in Chinese).
谭超林.选区激光熔化成型马氏体时效钢及其复合、梯度材料研究.博士学位论文,华南理工大学,2019.
18 Stašić J,Božić D. Surface & Coatings Technology,2016,307,407.
19 Aimangour B, Grzesiak D, Yang J M. Materials and Design,2016,96,150.
20 Astfalck L C,Kelly G K,Li X P,et al. Advanced Engineering Materials,2017,19(8),1600835.
21 Gu D D,Wang H Q,Chang F,et al. Physics Procedia,2014,56,108.
22 Simchi A,Godlinski D. Journal of Materials Science,2011,46(5),1446.
23 Chang F.Research on forming mechanisms and properties of multiphase reinforced aluminum matrix composites by selective laser melting.Master's Thesis,Nanjing University of Aeronautics and Astronautics,China, 2016 (in Chinese).
常斐.选区激光熔化多相增强Al基复合材料成形机理及性能研究.硕士学位论文,南京航空航天大学,2016.
24 Hu L,Liu Y Z,Tu C,et al. Materials Science and Engineering of Powder Metallurgy,2019,24(4),365 (in Chinese).
胡亮,刘允中,涂诚,等.粉末冶金材料科学与工程,2019,24(4),365.
25 Gu D D,Hagedorm Y C,Meiners W,et al. Composites Science and Technology,2011,71(13),1612.
26 Gu D D,Meng G B,Li C,et al. Scripta Materialia,2012,67(2),185.
27 Li C,Gu D D,Shen Y F,et al. The Chinese Journal of Nonferrous Metals,2011,21(7),1554 (in Chinese).
李闯,顾冬冬,沈以赴,等.中国有色金属学报,2011,21(7),1554.
28 Attar H,Bonisch M,Calin M,et al. Acta Materialia,2014,76,13.
29 Hattal A,Chauveau T,Djemai M,et al. Materials and Design,2019,180,107909.
30 Jia Q B,Gu D D. Journal of Materials Research,2014,29(17),1960.
31 Jia Q B.Selective laser melting fabrication of Nickel-based superalloys and its composites: process,microstructure and property.Master's Thesis,Nanjing University of Aeronautics and Astronautics,China, 2015 (in Chinese).
贾清波.Ni基高温合金及其复合材料选区激光熔化成形工艺、组织及性能.硕士学位论文,南京航空航天大学,2015.
32 Cao C S.Research on preparation and properties of WC/Ni coating by laser melt injection.Master's Thesis,Huazhong University of Science and Technology,China, 2016 (in Chinese).
曹聪帅.激光熔注WC/Ni基复合材料层制备工艺及组织性能研究.硕士学位论文,华中科技大学,2016.
33 Nguyen Q B,Zhu Z,Chua B W,et al. Archives of Civil & Mechanical Engineering (Elsevier Science),2018,18(4),1410.
34 Xia M J, Gu D D, Ma C L,et al. Journal of Alloys and Compounds,2019,777,693.
35 Shi Q M.Process and performance control of laser additive manufacturing of Ni-based composites based on thermal-mechanical coupled method.Master's Thesis,Nanjing University of Aeronautics and Astronautics,China, 2018 (in Chinese).
石齐民.镍基复合材料激光增材制造热-力耦合过程及性能调控.硕士学位论文,南京航空航天大学,2018.
36 Xiao W H.The study of properties and microstructure on graphene/Inconel 718 composites prepared by 3D printing.Master's Thesis,Nanchang Hangkong University,China, 2017 (in Chinese).
肖纬汗.3D打印石墨烯/Inconel718复合材料组织与性能研究.硕士学位论文,南昌航空大学,2017.