Materials Reports 2019, Vol. 33 Issue (z1): 74-77 |
INORGANIC MATERIALS AND CERAMIC MATRIX COMPOSITES |
|
|
|
|
|
Preparation and Structure Modulation of TiC Gradient Coating on Graphite Surface |
HU Ting, WAN Hong, HUA Ye, GONG Jinyu, CHEN Xingyu
|
College of Aerospace Science and Engineering, National University of Defense Technology, Changsha 410073 |
|
|
Abstract High temperature oxidation resistance of graphite can be effectively improved by a gradient TiC coating, which is in-situ reacted on the graphite surface. The in-situ reaction mechanism, using Ti, TiO2 and NH4Cl as pack cementation agent to prepare TiC gradient coating on the surface of graphite, was investigated by the combination of experimental and chemical thermodynamic calculations in this paper. Also, based on the analyses of coating formation kinetics, the influence of temperature and pressure on the structure of the coating was studied. The results show that in the process of pack cementation on graphite substrate, TiO2 does not act as an inert filler, but participates in the reaction as a reactant and promotes the formation of TiC. This is different from the formation mechanism of TiC coating on the carbon steel surface using the same cementing agents. Without changing the composition of the cementing agent, increasing the partial pressure of the TiCl3 gas is beneficial to the increase of the gas diffusion rate, thereby increasing the thickness of the gradient coating. On the other hand, though the diffusion rate of TiCl3 gas is increased with the increase of the pack cementation temperature, the permeability of the TiCl3 gas is decreased as the rate of reaction between TiCl3 gas and graphite increases with temperature. Therefore, the structure of the gradient coating can be modulated by the controlling of pack cementation temperature. Under the existing experimental conditions, the thickness of the gradient TiC in the graphite is continuously reduced and the thickness of the surface TiC coating on the graphite is continuously increased when the pack cementation temperature is increased from 1 000 ℃ to 1 500 ℃, resulting in the coating structure is changed from the TiC gradient coating to the TiC surface coating.
|
Published: 05 July 2019
|
|
About author:: Ting Hu received his M.S. degree in materials science and engineering from the National University of Defense Technology in December 2018. Mainly engaged in research in the field of electronic functional materials.Hong Wan received her Ph.D. degree in materials scie-nce and engineering from the National University of Defense Technology in 2005.She is currently an associa-te Professor in the Department of Materials Science and Engineering, National University of Defense Technology. Her current research interests include high current diodes and materials of cathodes for intense electron beam generation |
|
|
1 李圣华. 炭和石墨制品,冶金工业出版社,1981. 2 饶娟,张盼,何帅,等. 中国科学,2017,47(1),13. 3 Mantel C L. Handbook of carbon, graphite,diamond and fullerenes,Noyes publications,USA,1993. 4 Wilson B. Lubrication and Tribology,1995,47(6), 6. 5 Rajan T P D,et al. Journal of Materials Science,1998,3(3),3491. 6 Goth Y, Koike M. Materials Research Bulletin,2001,36(13),2263. 7 Liu X, Zhang S. Journal of the American Ceramic Society,2007,91(2),667. 8 曹晓明,温鸣,杜安. 现代金属表面合金化技术,化学工业出版社,2006. 9 楼白杨. 热加工工艺,1992(1),33. 10 楼白杨.浙江大学学报,1992(2),21. 11 黄济元.金属热处理,1991(2),3. 12 翟云芳. 渗流力学,石油工业出版社,1999. 13 孔祥言. 高等渗流力学,中国科学技术大学出版社,2010. |
|
|
|