3D打印技术应用于大尺度建筑的研究进展

doi:10.11896/j.issn.1005-023X.2018.23.017

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (2646KB)
Export: BibTeX | EndNote (RIS)

Abstract Applying 3D printing technology in the construction industry is one of the hot issues in current engineering field due to its automation and intelligentization, However, there are still many unsolved problems in designing method, printing material, printing equipment and construction technology, which hinder its further promotion and application. Implementation of 3D printing technology in the construction industry is still in the prototype stage at present. Compared with traditional building construction, 3D printing technology has following potential advantages, Ⅰ.high degree of mechanization, fast construction speed and low cost, Ⅱ. template free construction and less resource consumption, Ⅲ.low labor intensity and labor saving, Ⅳ.the construction process is safe, clean and accurate, Ⅴ.free design, light weight, high strength and multifunction, Ⅵ.highly customized, possible for realizing both standardization and personalization.
However, 3D printing construction technology cannot be directly used to traditional common concrete on account of the different construction techniques. Generally, the materials which were treated via layer by layer manner invariably accompany with the defects of low structure and formation of weak joints between material layers. Therefore, impressive efforts have been devoted by researchers in the investigation of material mix proportion, optimum structural design, evaluation criterion and construction technology. Lately, some cases have been reported that the 3D printing technology has been successfully adopted to personalized housing and bridge construction.
Successful applications of large-scale 3D printing technology in construction filed,include contour forming crafting, concrete printing crafting, D-type printing crafting and digital fabrication crafting, among which the contour forming crafting has been a mainstream technology. The main features of 3D printing construction technology are summarized as follows: layering concrete based on extrusion, power table-board bonding with binder techniques and reinforcement gridding. In order to meet the requirements of 3D printing technology, the printing materials are required to maintain certain extrudability, buildability, cohesiveness, workable duration and high strength during the printing process. Meanwhile, some enhanced measurements should been taken to insure the safety and reliability of the concrete structures. In addition, with the integration of different technologies, the combination of several technologies may be involved in the application of a specific project.
This paper systematically summarizes the development and research progress of large-scale 3D printing construction technology. Moreover, it also reviews the key problems of 3D printing technology such as. raw material selection, the feature of structural reinforcement measures by virtue of the fiber-reinforced cement-based materials. Furthermore, the development direction of applying 3D printing technology in construction industry is also proposed, which provide a reference for its further application and promotion.

Key words： construction industry three dimensional (3D) printing fiber reinforced cement-based materials material characteristics reinforcement measures

Published: 20 December 2018

CLC number:

TU528

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHU Binrong
	PAN Jinlong
	ZHOU Zhenxin
	ZHANG Yang

Cite this article:

ZHU Binrong,PAN Jinlong,ZHOU Zhenxin, et al. Advances in Large-scale Three Dimensional Printing Technology Applied in Construction Industry[J]. Materials Reports, 2018, 32(23): 4150-4159.

URL:

http://www.mater-rep.com/EN/10.11896/j.issn.1005-023X.2018.23.017 OR http://www.mater-rep.com/EN/Y2018/V32/I23/4150

1 Warnke P H, Seitz H, Warnke F, et al.Ceramic scaffolds produced by computer-assisted 3D printing and sintering: Characterization and biocompatibility investigations[J].Journal of Biomedical Materials Research Part B Applied Biomaterials,2010,93(1):212.
2 Gorsse S, Hutchinson C, Gouné M, et al.Additive manufacturing of metals: A brief review of the characteristic microstructures and pro-perties of steels, Ti-6Al-4V and high-entropy alloys[J].Science & Technology of Advanced Materials,2017,18(1):584.
3 Milewski J O.Additive manufacturing of metals[M]. Springer,2017.
4 Megahed M, Mindt H W, N’dri N, et al.Metal additive-manufacturing process and residual stress modeling[J].Integrating Materials & Manufacturing Innovation,2016,5(1):1.
5 Shakor P, Sanjayan J, Nazari A, et al.Modified 3D printed powder to cement-based material and mechanical properties of cement scaffold used in 3D printing[J].Construction & Building Materials,2017,138:398.
6 Ngo T D, Kashani A, Imbalzano G, et al.Additive manufacturing (3D printing): A review of materials, methods, applications and challenges[J].Composites Part B Engineering,2018,143:172.
7 Khoshnevis B.Automated construction by contour crafting—Related robotics and information technologies[J].Automation in Construction,2004,13(1):5.
8 Khoshnevis B, Hwang D, Yao K T, et al.Mega-scale fabrication by contour crafting[J].International Journal of Industrial & Systems Engineering,2006,1(3):301.
9 Xu J, Ding L, Love P E D. Digital reproduction of historical building ornamental components: From 3D scanning to 3D printing[J].Automation in Construction,2017,76:85.
10 Zhang J, Khoshnevis B.Optimal machine operation planning for construction by contour crafting[J].Automation in Construction,2013,29(1):50.
11 Lim S, Buswell R A, Le T T, et al.Developments in construction-scale additive manufacturing processes[J].Automation in Construction,2012,21(1):262.
12 Panda B N, Tay D, Paul S C, et al.Current challenges and future potential of 3D concrete printing[J].Materialwissenschaft Und Werkstofftechnik,2018,49:666.
13 Wolfs R J M. 3D printing of concrete structures[D].Eindhoven: Eindhoven University of Technology,2015.
14 Panda B, Paul S C, Mohamed N A N, et al. Measurement of tensile bond strength of 3D printed geopolymer mortar[J].Measurement,2017,113:108.
15 Gosselin C, Duballet R, Roux P, et al.Large-scale 3D printing of ultra-high performance concrete—A new processing route for architects and builders[J].Materials & Design,2016,100:102.
16 Asprone D, Auricchio F, Menna C, et al.3D printing of reinforced concrete elements: Technology and design approach[J].Construction & Building Materials,2018,165:218.
17 Bos F, Wolfs R, Ahmed Z, et al.Additive manufacturing of concrete in construction: Potentials and challenges of 3D concrete printing[J].Virtual and Physical Prototyping,2016,11:209.
18 Wolfs R J M, Bos F P, Salet T A M, et al. Early age mechanical behaviour of 3D printed concrete: Numerical modelling and experimental testing[J].Cement & Concrete Research,2018,106:103.
19 Costanzi C B, Ahmed Z Y, Schipper H R, et al.3D Printing Concrete on temporary surfaces: The design and fabrication of a concrete shell structure[J].Automation in Construction,2018,94:395.
20 Asprone D, Menna C, Bos F P, et al.Rethinking reinforcement for digital fabrication with concrete[J].Cement & Concrete Research, 2018, 112: 111.
21 Salet T A M, Ahmed Z Y, Bos F P, et al. Design of a 3D printed concrete bridge by testing[J].Virtual and Physical Prototyping,2018,13(3):222.
22 Le T T, Austin S A, Lim S, et al.Mix design and fresh properties for high-performance printing concrete[J].Materials & Structures,2012,45(8):1221.
23 Ma G W, Wang L, Ju Y.State-of-the-art of 3D printing technology of cementitious material—An emerging technique for construction[J].Science China Technological Sciences,2018,61:475.
24 Lim S, Buswell R A, Le T T, et al.Development of a viable concreteprinting process[C]∥28th International Symposium on Automationand Robotics in Construction. Seoul,2011:665.
25 Paul S C, Yi W D T, Panda B, et al. Fresh and hardened properties of 3D printable cementitious materials for building and construction[J].Archives of Civil & Mechanical Engineering,2018,18(1):311.
26 Lim S, Le T, Webster J, et al.Fabricating construction components using layer manufacturing technology[C]∥Global Innovation in Construction Conference. Leicestershire,2009:512.
27 Lim S, Buswell R A, Valentine P J, et al.Modelling curved-layered printing paths for fabricating large-scale construction components[J].Additive Manufacturing,2016,12:216.
28 Perkins I, Skitmore M.Three-dimensional printing in the construction industry: A review[J].International Journal of Construction Management,2015,15(1):1.
29 Cesaretti G, Dini E, Kestelier X D, et al.Building components for an outpost on the Lunar soil by means of a novel 3D printing techno-logy[J].Acta Astronautica,2014,93(1):430.
30 Benvenuti S.Living on the Moon: Topological Optimization of a 3D-Printed Lunar Shelter[J].Nexus Network Journal,2013,15(2):285.
31 Ghaffar S H, Corker J, Fan M.Additive manufacturing technology and its implementation in construction as an eco-innovative solution[J].Automation in Construction,2018,93:1.
32 Colla V, Dini E.Large Scale 3D Printing: From deep sea to the moon[M].The Abdus Salam Center for Theoretical Physics,2013.
33 Behind the 3d printed bridge: exclusive interview with catalonian designers at iaac.[DB/OL].(2017-11-21)[2017-12-13].https:∥3dprintingindustry.com/news/behind-3d-printed-bridge-exclusive-interview-catalonian-designers-iaac-101391/
34 Gershenfeld N.How to make almost anything: The digital fabrication revolution[J].Foreign Affairs,2012,91(6):43.
35 Dunn N.Digital fabrication in architecture[M].Laurence King,2012.
36 Gramazio F, Kohler M, Langenberg S.Fabricate: Negotiating design & making[M].Gtaverlag,2014.
37 Lauer W V.Mesh-Mould: Robotically fabricated spatial meshes as reinforced concrete formwork[J].Architectural Design,2014,84(3):44.
38 Soto B G D, Agustí-Juan I, Hunhevicz J, et al. Productivity of di-gital fabrication in construction: Cost and time analysis of a robotically built wall[J].Automation in Construction,2018,92:297.
39 Buchli J, Giftthaler M, Kumar N, et al.Digital in situ fabrication-Challenges and opportunities for robotic in situ fabrication in architecture, construction, and beyond[J].Cement and Concrete Research,2018,112:66.
40 Agustí-Juan I, Müller F, Wangler T, et al.Potential benefits of di-gital fabrication for complex structures: Environmental assessment of a robotically fabricated concrete wall[J].Journal of Cleaner Production,2017,154:330.
41 Branch technology and algix 3d partner to deliverthe next revolution in 3D printing. [DB/OL]. (2017-09-01) [2017-12-14]. https:∥www.branch.technology/blogs/2017/9/1/branch-3d-prints-in-bio-material
42 Agustí-Juan I, Habert G.Environmental design guidelines for digital fabrication[J].Journal of Cleaner Production,2017,142:2780.
43 Rippmann M, Block P.Rethinking structural masonry: Unreinforced, stone-cut shells[J].Construction Materials,2013,66(6):378.
44 Willmann J, Knauss M, Apolinarska A A, et al.Robotic timber construction—Expanding additive fabrication to new dimensions[J].Automation in Construction,2016,61:16.
45 Keating S J, Leland J C, Cai L, et al.Toward site-specific and self-sufficient robotic fabrication on architectural scales[J].Science Robotics,2017,2(5):1.
46 Wangler T, Lloret E, Reiter L, et al.Digital concrete: Opportunities and challenges[J].RILEM Technical Letters,2016,1:67.
47 Khalil N, Aouad G, Cheikh K E, et al.Use of calcium sulfoaluminate cements for setting control of 3D-printing mortars[J].Construction & Building Materials,2017,157:382.
48 Perrot A, Rangeard D, Pierre A.Structural built-up of cement-based materials used for 3D-printing extrusion techniques[J].Materials & Structures,2016,49(4):1213.
49 Sanchez F, Sobolev K.Nanotechnology in concrete—A review[J].Construction & Building Materials,2010,24(11):2060.
50 Güneyisi E, Geso<inline-formula><mml:math xmlns:mml="http://www.w3.org/1998/Math/MathML" id="Mml1-1005-023X-32-23-4150"><mml:mover accent="true"><mml:mi>g</mml:mi><mml:mtext fontstyle="italic">˙</mml:mtext></mml:mover></mml:math></inline-formula>lu M, Algin Z, et al. Optimization of concrete mixture with hybrid blends of metakaolin and fly ash using response surface method[J].Composites Part B Engineering,2014,60(2):707.
51 Yang Y, Yang E H, Li V C.Autogenous healing of engineered cementitious composites at early age[J].Cement & Concrete Research,2011,41(2):176.
52 Qiu J, Tan H S, Yang E H.Coupled effects of crack width, slag content, and conditioning alkalinity on autogenous healing of engineered cementitious composites[J].Cement & Concrete Composites,2016,73:203.
53 Kim J K, Kim J S, Ha G J, et al.Tensile and fiber dispersion performance of ECC (engineered cementitious composites) produced with ground granulated blast furnace slag[J].Cement & Concrete Research,2007,37(7):1096.
54 Wongkornchaowalit N, Lertchirakarn V.Setting time and flowability of accelerated Portland cement mixed with polycarboxylate superplasticizer[J].Journal of Endodontics,2011,37(3):387.
55 He Y, Zhang X, Hooton R D.Effects of organosilane-modified polycarboxylate superplasticizer on the fluidity and hydration properties of cement paste[J].Construction & Building Materials,2017,132:112.
56 Singh M, Siddique R.Properties of concrete containing high volumes of coal bottom ash asfine aggregate[J].Journal of Cleaner Production,2015,91:269.
57 Singh M, Siddique R.Strength properties and micro-structural pro-perties of concrete containing coal bottom ash as partial replacement of fine aggregate[J].Construction & Building Materials,2014,50(4):246.
58 Sahmaran M, Li V C.Durability properties of micro-cracked ECC containing high volumes fly ash[J].Cement & Concrete Research,2009,39(11):1033.
59 Yu J, Lu C, Leung C K Y, et al. Mechanical properties of green structural concrete with ultrahigh-volume fly ash[J].Construction & Building Materials,2017,147:510.
60 Kazemian A, Yuan X, Cochran E, et al.Cementitious materials for construction-scale 3D printing: Laboratory testing of fresh printing mixture[J].Construction & Building Materials,2017,145:639.
61 Paul S C, Yi W D T, Panda B, et al. Fresh and hardened properties of 3D printable cementitious materials for building and construction[J].Archives of Civil & Mechanical Engineering,2018,18(1):311.
62 Ma G W, Li Z J, Wang L.Printable properties of cementitious material containing copper tailings for extrusion based 3D printing[J].Construction & Building Materials,2018:613.
63 Weng Y, Li M, Tan M J, et al.Design 3D printing cementitious materials via Fuller Thompson theory and Marson-Percy model[J].Construction & Building Materials,2018,163:600.
64 Wallevik J E.Effect of the hydrodynamic pressure on shaft torque for a 4-blades vane rheometer[J].International Journal of Heat & Fluid Flow,2014,50:95.
65 Wallevik O H, Feys D, Wallevik J E, et al.Avoiding inaccurate interpretations of rheological measurements for cement-based mate-rials[J].Cement & Concrete Research,2015,78:100.
66 Zhu H, Martys N S, Ferraris C, et al.A numerical study of the flow of Bingham-like fluids in two-dimensional vane and cylinder rheometers using a smoothed particle hydrodynamics (SPH) based method[J].Journal of Non-Newtonian Fluid Mechanics,2010,165(7-8):362.
67 Mechtcherine V, Shyshko S.Simulating the behaviour of fresh concrete with the Distinct Element Method—Deriving model parameters related to the yield stress[J].Cement & Concrete Composites,2015,55:81.
68 Remond S, Pizette P.A DEM hard-core soft-shell model for the si-mulation of concrete flow[J].Cement & Concrete Research,2014,58(15):169.
69 Mechtcherine V, Gram A, Krenzer K, et al.Simulation of fresh concrete flow using Discrete Element Method (DEM): Theory and applications[J].Materials and Structures,2014,47(4):615.
70 Zareiyan B, Khoshnevis B.Interlayer adhesion and strength of structures in contour crafting—Effects of aggregate size, extrusion rate, and layer thickness[J].Automation in Construction,2017,81:112.
71 Panda B, Paul S C, Tan M J.Anisotropic mechanical performance of 3D printed fiber reinforced sustainable construction material[J].Materials Letters,2017,209:146.
72 Kazemian A, Yuan X, Cochran E, et al.Cementitious materials for construction-scale 3D printing: Laboratory testing of fresh printing mixture[J].Construction & Building Materials,2017,145:639.
73 Le T T, Austin S A, Lim S, et al.Hardened properties of high-performance printing concrete[J].Cement & Concrete Research,2012,42(3):558.
74 Zhao J, Chen C, Liang Y, et al.Mechanical properties and structure of Haliotis discus hannai Ino and Hemifusus tuba conch shells: A comparative study[J].Acta Mechanica Sinica,2010,26(1):21.