风积砂-黄土混合料与钢界面的环形剪切力学特性

doi:10.11896/cldb.23070012

Abstract
Figure/Table
References
Related Citation (2)

Download:

Full Text ( PDF ) (15898KB)
Export: BibTeX | EndNote (RIS)

Abstract The northern side of the Loess Plateau is bordered by many deserts, forming a widely distributed mixed distribution area of aeolian sand and loess. The aeolian sand-loess mixture (ASLM) presents different physical and mechanical characteristics under different proportion conditions, and the interfacial contact mechanical behavior of the ASLM foundation of ten occurs with other materials during field construction, and the relevant research is rarely mentioned at present. This work obtained the maximum dry density of the ASLM under different sand content conditions, prepared circular specimens of the ASLM with the same compaction degree and different sand content, and conducted ring shear tests on the interface between the ASLM and steel under different vertical pressures and shear velocities. The particle distribution properties and particle fragmentation characteristics of different sand content were observed using scanning electron microscopy, and the formation mechanism of resi-dual strength of ASLM with steel in ring shear condition was revealed. The test results show that the physical and mechanical characteristics of ASLM transition from loess to sandy soil with the increase of sand content. When the vertical pressure is less than 100 kPa, the probability of dilatancy of the mixture increases. There is a linear relationship between the interface residual strength and vertical pressure between the ASLM and the steel, which is consistent with the Mohr-Coulomb law. As the sand content increases, the crushing effect of aeolian sand particles increases, and the interfacial residual internal friction angle and the interfacial residual cohesion between the ASLM and steel decrease. An increase in shear rate shorten the contact time between the mixture and the steel interface, making it difficult to exert the contact and bite effects between the two, thereby reducing the residual strength of the interface between ASLM and steel. The research results predict the proportion of loess added to aeolian sand, which can provide useful reference for the treatment of aeolian sand foundation and also provide scientific reference for revealing the construction mechanics of ASLM.

Key words： aeolian sand-loess mixture steel interface ring shear test interface residual strength

Published: 10 March 2024 Online: 2024-03-18

CLC number:

TU411

Fund:National Natural Science Foundation of China (11972374) and Shaanxi Province Key R & D Plan Project (2022SF-084).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	YAO Zhihua
	ZHANG Jianhua
	XIN Jianping
	MU Rui

Cite this article:

YAO Zhihua,ZHANG Jianhua,XIN Jianping, et al. Ring Shear Characteristics Between Aeolian Sand-Loess Mixtures and Steel Interface[J]. Materials Reports, 2024, 38(5): 23070012-8.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.23070012 OR http://www.mater-rep.com/EN/Y2024/V38/I5/23070012

1 Du S S, Hong B, Wang L, et al. Geological Survey of China, 2018, 5(6), 83 (in Chinese).
杜少少, 洪勃, 王力, 等. 中国地质调查, 2018, 5(6), 83.
2 Ma T, Tang K F. Subgrade Engineering, 2010(5), 145 (in Chinese).
马涛, 唐开富. 路基工程, 2010(5), 145.
3 Zhu B, Yang X, Liu Z, et al. Environmental Earth Sciences, 2012, 66(1), 337.
4 Elipe M, Lopez-Querol S . Construction & Building Materials, 2014, 73(30), 728.
5 Mengistu A G, Rensburg L V, Mavimbela S . Catena, 2017, 158, 184.
6 Zhu Z D, Wu Z, Liu S, et al. An introduction to china desert, Science Press, China, 1980 (in Chinese).
朱震达, 吴正, 刘恕, 等. 中国沙漠概论, 科学出版社, 1980.
7 Yuan Y Q, Wang X C. Chinese Journal of Geotechnical Engineering, 2007, 29(3), 360 (in Chinese).
袁玉卿, 王选仓. 岩土工程学报, 2007, 29(3), 360.
8 Li Z Y. Research compaction mechanism and roadbed carring capacity of the eolian sand. Ph. D. Thesis, Chongqing Jiaotong University, China, 2003(in Chinese).
李志勇. 风积砂的压实机理及路用承载力研究. 博士学位论文, 重庆交通学院, 2003.
9 Wang G T, Wang X M, Lang L L. Journal of Desert Research, 2016(2), 281(in Chinese).
王广涛, 王训明, 郎丽丽. 中国沙漠, 2016(2), 281.
10 Meng Y H, Dong X K, Lyu Y Q. Journal of Henan Polytechnic University (Natural Science Edition), 2009, 28(3), 347 (in Chinese).
孟永会, 董秀坤, 吕远强. 河南理工大学学报(自然科学版), 2009, 28(3), 347.
11 Luo J W, Li X A, Zhao N, et al. Journal Engineering Geology, 2016, 24(5), 915(in Chinese).
骆建文, 李喜安, 赵宁, 等. 工程地质学报, 2016, 24(5), 915.
12 Deng X J, Sun L. Vehicle-ground structure system dynamics, People's Communications Press, China, 2000(in Chinese).
邓学钧, 孙璐. 车辆-地面结构系统动力学, 人民交通出版社, 2000.
13 Yan S W, Lin S, Jia Z L, et al. Chinese Journal of Geotechnical Enginee-ring, 2018, 40(3), 495 (in Chinese)
闫澍旺, 林澍, 贾沼霖, 等. 岩土工程学报, 2018, 40(3), 495.
14 Sheng S, Feng Z, Feng D C, et al. Cold Regions Science and Technology, 2020, 176, 103090.
15 Potyondy J G. Geotechnique, 1961, 11(4), 339.
16 Hong C X, Guo Q Z, Du Z C. Advanced Materials Research, 2011, 243-249, 2332.
17 Lin P Y, Guo P F, Guo C C, et al. Chinese Journal of Geotechnical Engineering, 2023, 45(1), 85 (in Chinese).
林沛元, 郭潘峰, 郭成超, 等. 岩土工程学报, 2023, 45(1), 85.
18 Uesugi M. Soils & Foundations, 1986, 26(4), 139.