玄武岩熔融出丝漏嘴长度对纤维成型的影响

doi:10.11896/cldb.25040180

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (20481KB)
Export: BibTeX | EndNote (RIS)

Abstract The successful formation of basalt fibers and the stability of the fiber drawing process are directly governed by the length parameter of the spinneret nozzle. The influence of spinneret nozzle length on basalt fiber formation was systematically investigated through the design of a quintuple-orifice crucible with precisely controlled nozzle dimensions of 2 mm, 3 mm, 4 mm, 5 mm, and 6 mm. Under standardized experimental conditions with consistent basalt melt composition and thermal environment, optimal fiber formation was achieved at 1 450 ℃, wherein the 3 mm nozzle exhibited superior process stability. While continuous filaments were obtainable with 2 mm and 4 mm nozzles, notable process fluctuations were observed. The 5 mm and 6 mm configurations demonstrated compromised fiber-forming capability under equivalent process parameters. The quantitative correlation between spinneret nozzle geometries and fiber formation efficiency was systematically validated through COMSOL Multiphysics simulations conducted at 1 450 ℃ melt temperature. Computational results demonstrated precise consistency with experimental observations regarding filament continuity and process stability across varying nozzle lengths. The inverse correlation between nozzle length and melt flow velocity was quantitatively established, wherein optimal fluidity characteristics were attained at the 3 mm configuration, whereas excessive velocity gradients induced by the 2 mm nozzle were identified as detrimental to fiber drawing stability. Concurrently, longitudinal thermal gra-dients within the melt were demonstrated to be inversely governed by nozzle length, with the 3 mm variant exhibiting minimal temperature variation along the flow path, thus enabling continuous fiber formation. By contrast, terminal temperature differentials ranging from 14.7 ℃ to 29.6 ℃ were recorded in 4—6 mm nozzles due to intensified convective heat dissipation, resulting in compromised fiber-forming continuity. A positive correlation between spinneret nozzle length and melt viscosity was established through characterization, with the 3 mm configuration exhibiting an optimal terminal viscosity differential of 3.2 Pa·s that ensured stable fiber formation. Progressive destabilization of the fiberization process was observed as the nozzle length increased, attributable to amplified viscosity gradient magnitudes within the melt flow field. An inverse correlation between basaltic melt viscosity and temperature was established. Optimal fiber formation efficiency was demonstrated under standardized conditions of 1 379.9 ℃ melt temperature, 1.08×10^-3 m/s flow velocity, and 48.5 Pa·s viscosity at the spinneret orifice, achieving superior process stability with the 3 mm nozzle configuration. The established methodology was validated as providing a critical optimization framework for spinneret nozzle length parameters and industrial fiber production process adjustments in basaltic melt fiberization systems.

Key words： basalt fiber melting spinneret nozzle length fiber formation simulation

Published: 25 April 2026 Online: 2026-05-06

CLC number:

TQ343+.9

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Chunyue
	ZHANG Qifan
	ZHANG Jianwei
	ZHANG Lei
	LIU Jiaqi
	WANG Qipeng

Cite this article:

LIU Chunyue,ZHANG Qifan,ZHANG Jianwei, et al. Effect of Basalt Melt-out Nozzle Length on Fiber Forming[J]. Materials Reports, 2026, 40(8): 25040180-7.

URL:

https://www.mater-rep.com/EN/10.11896/cldb.25040180 OR https://www.mater-rep.com/EN/Y2026/V40/I8/25040180

1 Liu J Q. Science & Technology Industry of China, 2024(8), 4(in Chinese).
刘嘉麒. 中国科技产业, 2024(8), 4.
2 Liu J Q. Science & Technology Review, 2009, 27(9), 3(in Chinese).
刘嘉麒. 科技导报, 2009, 27(9), 3.
3 Cheng P, Peng X H, Zhang Q M, et al. Acta Geologica Sichuan, 2025, 45(1), 182(in Chinese).
陈程, 彭秀红, 张乾梅, 等. 四川地质学报, 2025, 45(1), 182.
4 Zhang Y, Cai L. Fine and Specialty Chemicals, 2018, 26(12), 1(in Chinese).
张颖, 蔡蕾. 精细与专用化学品, 2018, 26(12), 1.
5 Gutnikov I S, Lazoryak I B. Fibers, 2019, 7(7), 65.
6 Li H P, Li D S, Long K. Glass & Enamel, 2012, 40(5), 1(in Chinese).
李会平, 李冬生, 龙凯. 玻璃与搪瓷, 2012, 40(5), 1.
7 Zhao X N, Dang X A, Ren W, et al. Journal of Lanzhou University of Technology, 2007(6), 61(in Chinese).
赵雪妮, 党新安, 任威, 等. 兰州理工大学学报, 2007(6), 61.
8 Liu Y. The development and applications of control system of bushing automatic assembling machine. Master's Thesis, Nanjing University of Aeronautics and Astronautics, China, 2014(in Chinese).
刘艳. 漏板漏嘴自动装配控制系统开发与应用. 硕士学位论文, 南京航空航天大学, 2014.
9 Dong H F, Yu S. Glass Fibers, 2012(3), 33(in Chinese).
董鹤峰, 于水. 玻璃纤维, 2012(3), 33.
10 Han Q H, Fang F K, Zhang X G, et al. Glass Fibers, 2018(5), 34(in Chinese).
韩庆贺, 方法奎, 张贤光, 等. 玻璃纤维, 2018(5), 34.
11 Li J J, Liu Y P, Chen J S. Bulletin of the Chinese Ceramic Society, 2008(5), 1076(in Chinese).
李建军, 刘艳春, 陈继生. 硅酸盐通报, 2008(5), 1076.
12 Zeng J H, Chen D Q, Li H R, et al. Bulletin of the Chinese Ceramic Society, 2024, 43(4), 1246(in Chinese).
曾健华, 陈德全, 李浩然, 等. 硅酸盐通报, 2024, 43(4), 1246.
13 Zhu L P, Yu S F, Lv S W, et al. Chemical Industry and Engineering Progress, 2019, 38(2), 940(in Chinese).
朱立平, 于守富, 吕士武, 等. 化工进展, 2019, 38(2), 940.
14 Liu S S, Guo F. Chinese Labat Man, 2023, 60(3), 101(in Chinese).
刘斯顺, 郭锋. 蓄电池, 2023, 60(3), 101.
15 Zhang Q H, Li Y. Acta Physica Sinica, 2021, 70(13), 115(in Chinese).
张庆海, 李阳. 物理学报, 2021, 70(13), 115.
16 Sayouba K, Landry K S O, N′ Djédanoum T, et al. Physical Science International Journal, 2024, 28(6), 157.
17 Bossinov D. Defect and Diffusion Forum, 2025, 440, 55.