基于印刷技术制备钙钛矿太阳电池

doi:10.11896/j.issn.1005-023X.2018.09.001

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (3317KB)
Export: BibTeX | EndNote (RIS)

Abstract Perovskite solar cells (PSCs) have attracted much attention during the past years due to their excellent photovoltaic properties and low-cost solution processing. The power conversion efficiency (PCE) has been rapidly increased to 22.7% since the first report of 3.8% in 2009, which approaches the levels of commercial polycrystalline silicon solar cells, CdTe solar cells and CIGS solar cells. Spin-coating is commonly used to fabricate PSCs in the labs, but it can’t meet the requirements for large-scale and low-cost process. It is simple to operate the spin-coating process with good repeatability. However, spin-coating still possesses some shortcomings, including serious waste of materials, only producing film without patterns, incapable of continuous fabrication. Therefore, it cannot match with the production of industrialization with large area and high throughout. It is still a big challenge to transfer the fabrication from lab-scale to large-scale industrialization with low cost and high throughout. Printing techniques show many advantages, e.g. high material utilization, low cost, large area, high throughout and matching with flexible substrate, and they have been used to fabricate PSCs. The PCE approaching 20% was achieved in printed, small-area PSCs, and numerous efforts have been made to improve printed large-area PSCs with PCE between 10% and 16%. Furthermore, it has already achieved printed, flexible PSCs with PCE of about 10%. There are still many issues to be solved for accelerating the industrialization. Ⅰ. Solvent engineering and gas-assisted treatment, commonly used in spin-coating process for producing high-quality perovskite films, are not matchable with printing process, resulting in the poor morphology and the low reproducibility in printed perovskite film. Ⅱ. The high-temperature annealing process would restrict the use of flexible substrate and the choice of interfacial materials. Ⅲ. Perovskite materials are sensitive to humidity, and it is necessary to improve their environment adaptability and reduce the cost. Hence, it is very important to optimize printing techniques for fabricating large-area PSCs with high efficiency, high throughout and low cost. In this review, we summarize the research progress on PSCs fabricated via printing techniques, including inkjet-printing, spray-coating, slot-die coating, doctor-blading. Furthermore, we also discuss the challenges and prospects of potential commercial PSCs.

Key words： perovskite printing techniques solar cells

Published: 10 May 2018 Online: 2018-07-06

CLC number:

TM914.4+2

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LI Hengyue
	GONG Chendi
	HUANG Keqing
	YANG Junliang

Cite this article:

LI Hengyue,GONG Chendi,HUANG Keqing, et al. A Review on the Fabrication of Perovskite Solar Cells via Printing Techniques[J]. Materials Reports, 2018, 32(9): 1385-1400.

URL:

https://www.mater-rep.com/EN/10.11896/j.issn.1005-023X.2018.09.001 OR https://www.mater-rep.com/EN/Y2018/V32/I9/1385

1 Kojima A, Teshima K, Shirai Y, et al. Organometal halide perovskites as visible-light sensitizers for photovoltaic cells[J].Journal of the American Chemical Society,2009,131(17):6050.
2 https:∥www.nrel.gov/pv/assets/images/efficiency-chart.png
3 Kim H S, IM S H, Park N G. Organolead halide perovskite: New horizons in solar cell research[J].Journal of Physical Chemistry C,2014,118(11):5615.
4 Baikie T, Fang Y, Kadro J M, et al. Synthesis and crystal chemistry of the hybrid perovskite (CH₃NH₃)PbI₃ for solid-state sensitised solar cell applications[J].Journal of Materials Chemistry A,2013,1(18):5628.
5 Ma Y, Wang S, Zheng L, et al. Recent research developments of perovskite solar cells[J].Chinese Journal ofChemistry,2014,32(10):957.
6 Im J H, Chung J, Kim S J, et al. Synthesis, structure, and photovoltaic property of a nanocrystalline 2H perovskite-type novel sensitizer (CH₃CH₂NH₃)PbI₃[J].Nanoscale Research Letters,2012,7(1):353.
7 Gao P, Graetzel M, Nazeeruddin M K. Organohalide lead perovskites for photovoltaic applications[J].Energy & Environmental Science,2014,7(8):2448.
8 Burschka J, Pellet N, Moon S J, et al. Sequential deposition as a route to high-performance perovskite-sensitized solar cells[J].Nature,2013,499:316.
9 Liu M, Johnston M B, Snaith H J. Efficient planar heterojunction perovskite solar cells by vapour deposition[J].Nature,2013,501:395.
10 Chen Q, Zhou H, Hong Z, et al. Planar heterojunction perovskite solar cells via vapor-assisted solution process[J].Journal of the American Chemical Society,2014,136(2):622.
11 Im J H, Lee C R, Lee J W, et al. 6.5% efficient perovskite quantum-dot-sensitized solar cell[J].Nanoscale,2011,3(10):4088.
12 Kim H S, Lee C R, Im J H, et al. Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%[J].Scientific Reports,2012,2:591.
13 Lee M M, Teuscher J, Miyasaka T, et al. Efficient hybrid solar cells based on meso-superstructured organometal halide perovskites[J].Science,2012,338(6107):643.
14 Heo J H, Im S H, Noh J H, et al. Efficient inorganic-organic hybrid heterojunction solar cells containing perovskite compound and polymeric hole conductors[J].Nature Photonics,2013,7:486.
15 Jiang Q, Chu Z N, Wang P Y, et al. Planar-structure perovskite solar cells with efficiency beyond 21%[J].Advanced Materials,2017,29(46):1703852.
16 Yang W S, Park B W, Jung E H, et al. Iodide management in for-mamidinium-lead-halide-based perovskite layers for efficient solar cells[J].Science,2017,356(6345):1376.
17 Norrman K, Ghanbari-Siahkali A, Larsen N B. Studies of spin-coated polymer films[J].Annual Reports Section “C”(Physical Chemistry),2005,101:174.
18 Krebs F C. Fabrication and processing of polymer solarcells: A review of printing and coating techniques[J].Solar Energy Materials and Solar Cells,2009,93(4):394.
19 Ku Z L, Rong Y G, Xu M, et al. Full printable processed mesosco-pic CH₃NH₃PbI₃/TiO₂ heterojunction solar cells with carbon coun-ter electrode[J].Scientific Reports,2013,3:3132.
20 Mei A, Li X, Liu L, et al. A hole-conductor-free, fully printable mesoscopic perovskite solar cell with high stability[J].Science,2014,345(6194):295.
21 Chen K, Gao W, Emaminejad S, et al. Printed carbon nanotube electronics and sensor systems[J].Advanced Materials (Weinheim),2016,28(22):4397.
22 Li Y, Jian F. An inkjet-printed TTF-TCNQ nanoweb as an effective modification layer for high mobility organic field-effect transistors[J].Journal of Materials Chemistry C,2014,2(8):1413.
23 Hu Q, Wu H, Sun J, et al. Large-area perovskite nanowire arrays fabricated by large-scale roll-to-roll micro-gravure printing and doctor blading[J].Nanoscale,2016,8(9):5350.
24 Tong S, Wu H, Zhang C, et al. Large-area and high-performance CH₃NH₃PbI₃ perovskite photodetectors fabricated via doctor blading in ambient condition[J].Organic Electronics,2017,49:347.
25 Peng Y, Xiao S, Yang J, et al. The elastic microstructures of inkjet printed polydimethylsiloxane as the patterned dielectriclayer for pressure sensors[J].Applied Physics Letters,2017,110(26):261904.
26 Zhang C, Luo Q, Wu H, et al. Roll-to-roll micro-gravure printed large-area zinc oxide thin film as the electron transport layer for solution-processed polymer solar cells[J].Organic Electronics,2017,45:190.
27 Kim C, Ian G, Eric B, et al. Direct legend printing (DLP) on printed circuit boards using piezoelectric inkjet technology[J].Circuit World,2002,28(2):24.
28 Luo X, Zeng Z G, Wang X H, et al. Preparing two-dimensional nano-catalytic combustion patterns using direct inkjet printing[J].Journal of Power Sources,2014,271:174.
29 Zhang Y, He T, Liu G L, et al. One-pot mass preparation of MoS₂/C aerogels for high-performance supercapacitors and lithium-ion batteries[J].Nanoscale,2017,9(28):10059.
30 Kim D, Jenog S, Park B K, et al. Direct writing of silver conductive patterns: Improvement of film morphology and conductance by controlling solvent compositions[J].Applied Physics Letters,2006,89(26):2123.
31 Van D B A M J, De L A W M, Smith P J, et al. Geometric control of inkjet printed features using a gelating polymer[J].Journal of Materials Chemistry,2007,17(7):677.
32 Tian D L, Song Y L, Jiang L. Patterning of controllable surface wettability for printing techniques[J].Chemical Society Review,2013,42(12):5184.
33 Zhang L, Liu H T, Zhao Y, et al. Inkjet printing high-resolution, large-area graphene patterns by coffee-ring lithography[J].Advanced Materials,2012,24(3):436.
34 Kuang M X, Wang L B, Song Y L. Controllable printing droplets for high-resolution patterns[J].Advanced Materials,2014,26(40):6950.
35 Cao X, Wu F Q, Lau C, et al. Top-contact self-aligned printing for high performance carbon nanotube thin-film transistors with sub-micron channel length[J].ACS Nano,2017,11(2):2008.
36 Yin Z P, Huang Y A, Bu N B, et al. Inkjet printing for flexible electronics: Materials, processes and equipments[J].Chinese Science Bulletin,2010,55(30):3383.
37 Mette A, Richter P L, Horteis M, et al. Metal aerosol jet printing forsolar cell metallization[J].Progress in Photovoltaics,2007,15(7):621.
38 Horteis M, Glunz S W. Fine line printed silicon solar cells exceeding[J].Progress in Photovoltaics,2008,16(7):555.
39 Xia Y, Zhang W, Ha M J, et al. Printed sub-2 V gel-electrolyte-gated polymer transistors and circuits[J].Advanced Functional Mate-rials,2010,20(4):587.
40 Jones C S, Lu X J, Renn M, et al. Aerosol-jet-printed, high-speed, flexible thin-film transistor made using single-walled carbon nanotube solution[J].Microelectronic Engineering,2010,87(3):434.
41 Grunwald I, Groth E, Wirth I, et al. Surface biofunctionalization and production of miniaturized sensor structures using aerosol prin-ting technologies[J].Biofabrication,2010,2(1):014106.
42 Chang J, Lin Z, Li J, et al. Enhanced polymer thin film transistor performance by carefully controlling the solution self-assembly and film alignment with slot die coating[J].Advanced Electronic Mate-rials,2015,1(7):1500036.
43 阳军亮,吴涵,熊健,等.一种稳定的平面异质结钙钛矿太阳能电池及其制备方法:中国,201510121138.1[P].2015-03-20.
44 Liu F, Ferdous S, Schalble E, et al. Fast printing and in situ morphology observation of organic photovoltaics using slot-die coating[J].Advanced Materials (Weinheim),2015,27(5):886.
45 阳军亮,张楚俊,胡巧,等.一种大面积柔性功能石墨烯薄膜的卷对卷印刷制备方法:中国,201610380610.8[P].2016-06-01.
46 Padinger F, Brabec C J, Fromherz T, et al. Fabrication of large area photovoltaic devices containing various blends of polymer and fullerene derivatives by using the doctor blade technique[J].Opto-Electronics Review,2000,8(4):280.
47 Lin S Y, Yang B C, Zhou C H, et al. Efficient and stable planar hole-transport-material-free perovskite solar cells[J].Organic Electronics,2018,53:235.
48 Li S G, Tong S C, Yang J L, et al. High-performance formamidi-nium-based perovskite photodetectors fabricated via doctor-blading deposition in ambient condition[J].Organic Electronics,2017,47:102.
49 Xu L, Zhou C H, Wan F, et al. Stable monolithic hole-conductor-free perovskite solar cells using TiO₂ nanoparticle binding carbon films[J].Organic Electronics,2017,45:131.
50 Li S G, Yang B C, Wu R S, et al. High-quality CH₃NH₃PbI₃ thin film fabricated via intramolecular exchange for efficient planar he-terojunction perovskite solar cells[J].Organic Electronics,2016,39:304.
51 Wu H, Zhang C J, Ding K X, et al. Efficient planar heterojunction perovskite solar cells fabricated by in-situ thermal-annealing doctor blading in ambient condition[J].Organic Electronics,2017,45:302.
52 Sanyal M, Schmidt H B, Klein M F G, et al. In situ X-ray study of drying-temperature influence on the structural evolution of bulk-heterojunction polymer-fullerene solar cells processed by doctor-blading[J].Advanced Energy Materials,2011,1(3):363.
53 Sanyal M, Schmidt H B, Klein M F G, et al. Effect of photovoltaic polymer/fullerene blend composition ratio on microstructure evolution during film solidification investigated in real time by X-ray diffraction[J].Macromolecules,2011,44(10):3795.
54 Lee T M, Lee S H, Noh J H, et al. The effect of shear force on ink transfer in gravure offset printing[J].Journal of Micromechanics & Microengineering,2010,20(12):125026.
55 Chung D Y, Huang J S, Bradley D D C, et al. High performance, flexible polymer light-emitting diodes (PLEDs) with gravure contact printed hole injection and light emitting layers[J].Organic Electro-nics,2010,11(6):1088.
56 Lee H, Kim A, Cho S M, et al. Nanoscale thickness and roughness control of gravure printed organic light emitting layer with poly(N-vinyl carbazole) and Ir(ppy)₃[J].Journal of Nanoscience & Nanotechnology,2009,9(12):7278.
57 Hambsch M, Reuter K, Stanel M, et al. Uniformity of fully gravure printed organic field-effect transistors[J].Materials Science and Engineering:B,2010,170(1-3):93.
58 Kaihovirta N J, Tobjork D, Makela T, et al. Low-voltage organic transistors fabricated using reverse gravure coating on prepatterned substrates[J].Advanced Energy Materials,2008,10(7):640.
59 Voigt M M, Mackenzie R C I, Yau C P, et al. Gravure printing for three subsequent solar cell layers of inverted structures on flexible substrates[J].Solar Energy Materials and Solar Cells,2011,95(2):731.
60 Kopola P, Aernouts T, Guillerez S, et al. High efficient plastic solar cells fabricated with a high-throughput gravure printing method[J].Solar Energy Materials and Solar Cells,2010,94(10):1673.
61 崔铮.印刷电子学:材料、技术及其应用[M].北京:高等教育出版社,2012:3.
62 Wei Z, Chen H, Yan K, et al. Inkjet printing and instant chemical transformation of a CH₃NH₃PbI₃/nanocarbon electrode and interface for planar perovskite solar cells[J].Angewandte Chemie (International Edition),2014,53(48):13239.
63 Bag M, Jiang Z, Renna L A, et al. Rapid combinatorial screening of inkjet-printed alkyl-ammonium cations in perovskite solar cells[J].Materials Letters,2016,164:472.
64 Mathies F, Abzieher T, Hochstuhl A, et al. Multipass inkjet printed planar methylammonium lead iodide perovskite solar cells[J].Journal of Materials Chemistry A,2016,4(48):19207.
65 Li S G, Jiang K J, Su M J, et al. Inkjet printing of CH₃NH₃PbI₃ on a mesoscopic TiO₂ film for highly efficient perovskite solar cells[J].Journal of Materials Chemistry A,2015,3(17):9092.
66 Barrows A T, Pearson A J, Kwak C K, et al. Efficient planar he-terojunction mixed-halide perovskite solar cells deposited via spray-deposition[J].Energy & Environmental Science,2014,7(9):2944.
67 Bi Z, Liang Z, Xu X, et al. Fast preparation of uniform large grain size perovskite thin film in air condition via spray deposition method for high efficient planar solar cells[J].Solar Energy Materials and Solar Cells,2017,162:13.
68 Das S, Yang B, Gu G, et al. High-performance flexible perovskite solar cells by using a combination of ultrasonic spray-coating and low thermal budget photonic curing[J].ACS Photonics,2015,2(6):680.
69 Heo J H, Lee M H, Jang M H, et al. Highly efficient CH₃NH₃-PbI_3-xCl_x mixed halide perovskite solar cells prepared by re-dissolution and crystal grain growth via spray coating[J].Journal of Mate-rials Chemistry A,2016,4(45):17636.
70 Ishihara H, Chen W, Chen Y C, et al. Electrohydrodynamically assisted deposition of efficient perovskite photovoltaics[J].AdvancedMaterials Interfaces,2016,3(9):1500762.
71 Xia X, Li H, Wu W, et al. Efficient light harvester layer prepared by solid/mist interface reaction for perovskite solar cells[J].ACS Applied Materials & Interfaces,2015,7(31):16907.
72 Vak D, Hwang K, Faulks A, et al. 3Dprinter based slot-die coater as a lab-to-fab translation tool for solution-processed solar cells[J].Advanced Energy Materials,2015,5(4):1401539.
73 Hwang K, Jung Y S, Heo Y J, et al. Toward large scale roll-to-roll production of fully printed perovskite solar cells[J].Advanced Materials,2015,27(7):1241.
74 Cotella G, Baker J, Worsley D, et al. One-step deposition by slot-die coating of mixed lead halide perovskite for photovoltaic applications[J].Solar Energy Materials and Solar Cells,2017,159:362.
75 Jung Y S, Hwang K, Heo Y J, et al. One-Step printable perovskite films fabricated under ambient conditions for efficient and reproducible solar cells[J].ACS Applied Materials & Interfaces,2017,9(33):27832.
76 Qin T S, Huang W C, Kim J E, et al. Amorphous hole-transporting layer in slot-die coated perovskite solar cells[J].Nano Energy,2017,31:210.
77 Ciro J, Mejia M A, Jaramillo F. Slot-die processing of flexible pe-rovskite solar cells in ambient conditions[J].Solar Energy,2017,150:570.
78 Kim J H, Williams S T, Cho N, et al. Enhanced environmental stability of planar heterojunction perovskite solar cells based on blade-coating[J].Advanced Energy Materials,2015(5):141229.
79 Yang Z, Chueh C C, Zuo F, et al. High-performance fully printable perovskite solar cells via blade-coating technique under the ambient condition[J].Advanced Energy Materials,2015,5(13):1500328.
80 Mallajosyula A T, Fernando K, Bhatt S, et al. Large-area hysteresis-free perovskite solar cells via temperature controlled doctor blading under ambient environment[J].Applied Materials Today,2016,3:96.
81 Razza S, Di G F, Matteocci F, et al. Perovskite solar cells and large area modules (100 cm²) based on an air flow-assisted PbI₂ blade coating deposition process[J].Journal of Power Sources,2015,277:286.
82 Back H, Kim J, Kim G, et al. Interfacial modification of hole transport layers for efficient large-area perovskite solar cells achieved via blade-coating[J].Solar Energy Materials and Solar Cells,2016,144:309.
83 Hu Q, Zhao L C, Wu J, et al. In situ dynamic observations of pe-rovskite crystallisation and microstructure evolution intermediated from (PbI₆)^4- cage nanoparticles[J].Nature Communications,2017,8:15688.
84 Deng Y, Peng E, Shao Y, et al. Scalable fabrication of efficient organolead trihalide perovskite solar cells with doctor-bladed active la-yers[J].Energy &Environmental Science,2015,8(5):1544.
85 Deng Y, Dong Q, Bi C, et al. Air-stable, efficient mixed-cation pe-rovskite solar cells with Cu electrode by scalable fabrication of active layer[J].Advanced Energy Materials,2016,6(11):1600372.
86 Tang S, Deng Y, Zheng X, et al. Composition engineering in doctor-blading of perovskite solar cells[J].Advanced Energy Materials,2017,7(18):1700302.
87 Deng Y H, Wang Q, Yuan Y B, et al. Vividly colorful hybrid pe-rovskite solar cells by doctor-blade coating with perovskite photonic nanostructures[J].Materials Horizons,2015,2(6):578.
88 Yang M, Li Z, Reese M O, et al. Perovskite ink with wide proces-sing window for scalable high-efficiency solar cells[J].Nature Energy,2017,2:17038.
89 Hu Y, Si S, Mei A Y, et al. Stable large-area (10×10 cm²) printable mesoscopic perovskite module exceeding 10% efficiency[J].Solar RRL,DOI:10.1002/solr.201600019.
90 He M, Li B, Cui X, et al. Meniscus-assisted solution printing of large-grained perovskite films for high-efficiency solar cells[J].Nature Communications,2017,8:16045.
91 Hashmi S G, Martineau D, Li X, et al. Air processed inkjet infiltrated carbon based printed perovskite solar cells with high stability and reproducibility[J].Advanced Materials Technologies,2017,2(1):1600183.
92 Mohamad D K, Griffin J, Bracher C, et al. Spray-cast multilayer organometal perovskite solar cells fabricated in air[J].Advanced Energy Materials,2016,6(22):1600994.
93 Liang Z R, Zhang S H, Xu X Q, et al. A large grain size perovskite thin film with a dense structure forplanar heterojunction solar cells via spray deposition under ambient conditions[J].RSC Advances,2015,5(74):60562.
94 Chang W C,Lan D H, Lee K M, et al. Controlled deposition and performance optimization of perovskite solar cells using ultrasonic spray-coating of photoactive layers[J].ChemSusChem,2017,10(7):1405.
95 Nejand B A, Gharibzadeh S, Ahmadi V, et al. New scalable cold-roll pressing for post-treatment of perovskite microstructure in perovskite solar cells[J].Journal Physical Chemistry C,2016,120(5):2520.
96 Ramesh M, Boopathi K M, Huang T Y, et al. Using an airbrush pen for layer-by-layer growth of continuous perovskite thin films for hybrid solar cells[J].ACS Applied Materials & Interfaces,2015,7(4):2359.
97 Nejand B A, Gharibzadeh S, Ahmadi V, et al. Novel solvent-free perovskite deposition in fabrication of normal and inverted architectures of perovskite solar cells[J].Scientific Reports,2016,6:33649.
98 Jung Y S, Hwang K, Scholes F H, et al. Differentially pumped spray deposition as a rapid screening tool for organic and perovskite solar cells[J].Scientific Reports,2016,6:20357.
99 Habibi M, Ahmadian M R, Eslamian M. Optimization of spray coa-ting for the fabrication of sequentially deposited planar perovskite solar cells[J].Journal of Photonics for Energy,2017,7(2):022003.
100 Zabihi F, Ahmadian M R, Eslamian M. Fundamental study on the fabrication of inverted planar perovskite solar cells using two-step sequential substrate vibration-assisted spray coating (2S-SVASC)[J].Nanoscale Research Letters,2016,11:71.
101 Kavadiya S, Niedzwiedzki D M, Huang S, et al. Electrospray-assisted fabrication of moisture-resistant and highly stable perovskite solar cells at ambient conditions[J].Advanced Energy Materials,2017,7(18):1700210.
102 Chal G D, Luo S Q, Zhou H, et al. CH₃NH₃PbI_3-xBr_x perovskite solar cells via spray assisted two-step deposition: Impact of bromide on stability and cell performance[J].Material Design,2017,125:222.
103 Boopathi K M, Ramesh M, Perumal P, et al. Preparation of metal halide perovskite solar cells through a liquid droplet assisted method[J].Journal of Materials Chemistry A,2015,3(17):9257.
104 Li F M, Bao C X, Gao H, et al. A facile spray-assisted fabrication of homogenous flat CH₃NH₃PbI₃ films for high performance mesostructure perovskite solar cells[J].Materials Letters,2015,157:38.
105 Huang H B, Shi J J, Zhu L F, et al. Two-step ultrasonic spray deposition of CH₃NH₃PbI₃ for efficient and large-area perovskite solar cell[J].Nano Energy,2016,27:352.
106 Tait J G, Manghooli S, Qiu W, et al. Rapid composition screening for perovskite photovoltaics via concurrently pumped ultrasonic spray coating[J].Journal of Materials Chemistry A,2016,4(10):3792.
107 Chai G D, Wang S Z, Xia Z G, et al.PbI₂ platelets for inverted planar organolead halide perovskite solar cells via ultrasonic spray de-position[J].Semiconductor Science and Technology,2017,32(7):074003.
108 Schmidt T M, Larsen O T T, Carle J E, et al. Upscaling of perovskite solar cells: Fully ambient roll processing of flexible perovskite solar cells with printed back electrodes[J].Advanced Energy Materials,2015,5(15):1500569.
109 Gu Z W, Zuo L J, Larsen O T T, et al. Interfacial engineering of self-assembled monolayer modified semi-roll-to-roll planar heterojunction perovskite solar cells on flexible substrates[J].Journal of Materials Chemistry A,2015,3(48):24254.
110 Heo Y J, Kim J E, Weerasinghe H, et al. Printing-friendly sequential deposition via intra-additive approach for roll-to-roll process of perovskite solar cells[J].Nano Energy,2017,41:443.
111 Tzounis L, Stergiopoulos T, Zachariadis A, et al. Perovskite solar cells from small scale spin coating process towards roll-to-roll prin-ting: Optical and Morphological studies[J].Materials Today:Proceedings,2017,4(4):5082.
112 Kim J H, Williams S T, Cho N, et al. Enhanced environmental stability of planar heterojunction perovskite solar cells based on blade-coating[J].Advanced Energy Materials,2015,5(4):1401229.
113 Lee J W, Na S I, Kim S S. Efficient spin-coating-free planar heterojunction perovskite solar cells fabricated with successive brush-painting[J].Journal of Power Sources,2017,339:33.
114 Bag S, Deneault J R, Durstock M F. Aerosol-jet-assisted thin-film growth of CH₃NH₃PbI₃perovskites—A means to achieve high quality, defect-free films for efficient solar cells[J].Advanced Energy Materials,2017,7(20):1701151.