循环扩挤变形AZ80镁合金的组织、织构与力学性能<sup>*</sup>

doi:10.11896/j.issn.1005-023X.2017.016.012

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (1756KB)
Export: BibTeX | EndNote (RIS)

Abstract The CEE deformation process was conducted on AZ80. The microstructure and texture were observed and the mechanical properties were measured.The results showed that the grain size has been significantly refined after CEE deformation. After four-pass, the grain size refined from 150-230 μm to 2 μm, and the grains presented equiaxied and uniform. After two-pass, with the increase of passes, the degree of grain refinement reduced slowly. Simultaneously, after CEE, AZ80 magnesium alloy texture consisted of two different fiber texture: (0001) plane paralleled to the extrusion direction and (1120) prism which is perpendicular to the compression direction. With the increase of extrusion passes, the overall intensity of texture decreased firstly, then increased and finally decreased. Compared with the homogeneous state, the mechanical properties has obvious various. After one-pass CEE deformation, the tensile strength and yield strength reach the maximum value, and the value was 290 MPa and 180 MPa, respectively. After two-pass of CEE deformation, the strength is not enhanced with grain refinement (anti Hall-Petch theory). This is because the softening effect of texture is stronger than that of grain refinement. The elongation increases with the increase of extrusion passes.

Key words： cyclic expansion-extrusion AZ80 magnesium alloy texture

Published: 25 August 2017 Online: 2018-05-07

CLC number:

TG376.2

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	XUE Yong
	WU Yaojin
	YANG Zhihui
	ZHANG Zhimin

Cite this article:

XUE Yong,WU Yaojin,YANG Zhihui, et al. Microstructure,Texture and Mechanical Properties of AZ80 Magnesium Alloy Processed by Cyclic Expansion-extrusion[J]. Materials Reports, 2017, 31(16): 55-59.

URL:

https://www.mater-rep.com/EN/10.11896/j.issn.1005-023X.2017.016.012 OR https://www.mater-rep.com/EN/Y2017/V31/I16/55

1 Chen Bin,Lin Liangdong,Zeng Xiaoqin,et al.Present state and perspectives of severe plastic deformation[J].Mater Rev,2006,20(9):73(in Chinese).
陈彬,林栋梁,曾小勤,等.深度塑性变形技术的研究现状与前景[J].材料导报,2006,20(9):73.
2 Zhao Hui,Peng Xiaodong,Wang Yanguang,et al. Research status about plasticity improvement of wrought magnesium alloy[J].Rare Metals,2012,36(1):161(in Chinese).
赵辉,彭晓东,王艳光,等.变形镁合金的塑性改善研究现状[J].稀有金属,2012,36(1):161.
3 Lu Liwei, Zhao Jun, Liu Longfei,et al. Present achievements of severe plastic deformation on magnesium alloy[J]. Trans Mater Heat Treatment,2014,35(S1):1(in Chinese).
卢立伟,赵俊,刘龙飞,等.镁合金大塑性变形的研究进展[J].材料热处理学报,2014,35(S1):1.
4 He Yunbing,Pan Qingling,Liu Xiaoyan,et al.Microstructure and mechanical properties of ZK60 magnesium alloy produced by equal channel angular pressing[J]. Mater Eng,2011(6):32(in Chinese).
何运斌,潘清林,刘晓艳,等.ECAP法制备细晶ZK60镁合金的微观组织与力学性能[J].材料工程,2011(6):32.
5 Wang Qudong,Lin Jinbao,Peng Liming. Influence of cyclic extrusion and compression on the mechanical property of Mg alloy ZK60[J]. Chinese J Nonferrous Metals,2008,44(1):55(in Chinese).
王渠东,林金保,彭立明.往复挤压变形对ZK60镁合金力学性能的影响[J].中国有色金属学报,2008,44(1):55.
6 Pardis N, Chen C, Ebrahimi R, et al. Microstructure, texture and mechanical properties of cyclic expansion-extrusion deformed pure copper[J]. Mater Sci Eng A,2015,628:423.
7 Lu Jun,Zhen Li,Dong Jie,et al. Deformation behaviors of AZ31 magnesium alloy by equal channel angular extrusion[J]. Chinese J Nonferrous Metals,2009,19(3):424(in Chinese).
路君,靳丽.董杰,等.等通道角挤压变形AZ31镁合金的变形行为[J].中国有色金属学报,2009,19(3):424.
8 Kim W J,Jeong H G. Mechanical properties and texture evolution in ECAP processed AZ61 Mg alloys[J].Mater Sci Forum,2003,419/422:201.
9 Kim W J,Hong S I,Kim Y S. Texture evolution and its effects on the mechanical properties of AZ61Mg alloy by equal channel angular extrusion[J].Acta Mater,2003,51:3293.
10 樊刚.热挤压模具设计与制造基础[M].重庆:重庆大学,2001.
11 Babaei A, Mashhadi M M, Jafarzadeh H. Tube cyclic expansion- extrusion as a novel severe plastic deformation method for cylindrical tubes[J].Mater Sci Eng A,2014,49:3158.
12 Pardis N, Chen C, Shahbaz M, et al. Development of new routes of severe plastic deformation through cyclic expansion-extrusion process[J].Mater Sci Eng A,2014,613:357.
13 Rahimi F, Eivani A R, Kiani M. Effect of die design parameters on the deformation behavior in pure shear extrusion[J]. Mater Sci Eng A,2015,83:144.
14 Zhan Meiyan, Li Chunming, Shang Junlin.Investigation of the plastic deformation mechanism and twinning of magnesium alloys[J]. Mater Rev:Res,2011,25(2):1(in Chinese).
詹美燕,李春明,尚俊玲,等.镁合金的塑性变形机制与孪生变形研究[J].材料导报:研究篇,2011,25(2):1.
15 Ma Q, Li B, Whittington W R, et al. Texture evolution during dynamic recrystallization in a magnesium alloy at 450 ℃[J].Acta Mater,2014,67:102.
16 Zaharia L, Comaneci R, Chelariu R, et al.A new severe plastic deformation methed by repetitive extrusion and upsetting [J]. Mater Sci Eng A,2014,595:135.
17 Liu Chuming,Liu Zijuan,Zhu Xiurong,et al.Research and development progress of dynamic recrystallization in pure magnesium and its alloys[J]. Chinese J Nonferrous Metals,2006,16(1):1(in Chinese).
刘楚明,刘子娟,朱秀荣,等.镁及镁合金动态再结晶研究进展[J].中国有色金属学报,2006,16(1):1.
18 Lin Jinbao,Ren Weijie,Wang Xingyi. Research progress of crystal plasticity mechanics model in texture evolution of magnesium alloy[J].Mater Rev:Rev,2016,30(1):102(in Chinese).
林金保,任伟杰,王心怡.镁合金织构演化晶粒塑性力学模型的研究进展[J].材料导报:综述篇,2016,30(1):102.
19 Cui Chongliang,Hong Xiaolu,Sun Yanfu,et al.Research progress in deformation texture of wrought magnesium alloy[J].Ordnance Mater Sci Eng,2015,38(4):127(in Chinese).
崔崇亮,洪晓露,孙廷富,等.镁合金变形织构的研究进展[J].兵器材料科学与工程,2015,38(4):127.
20 Yan Gai,Sun Yangshan,Bai Jing,et al.Effects of rotary-die ECAP routes on microstructure and mechanical property of AZ31 magne-sium alloy[J].Acta Metall Sinica,2010,46(1):27(in Chinese).
严凯,孙扬善,白晶,等.转模等通道转角挤压路径对AZ31镁合金组织与力学性能的影响[J].金属学报,2010,46(1):27.
21 Fatemi-Varzaneh S M, Zarei-Hanzaki A Z, Naderi M, et al. Defor- mation homogeneity in accumulative back extrusion processing of AZ31magnesium alloy[J]. J Alloys Compd,2010,507:207.
22 Wang L P,Chen T,Jiang W Y,et al.Microstruture and mechanical properties of AM60B magnesium alloy alloy prepared by cyclic extrusion compression[J].Mater Sci Eng A,2013,23:3200.
23 Shi B Q, Chen R S, Ke W, et al.Effects of forgeing prodessing on the texture and tensile properties of ECAEed AZ80 magnesium alloy[J].Mater Sci Eng A,2012,546:323.
24 Chen Yongjun,Wang Qudong,Peng Jianguo,et al. Research and development prospects of uilrafine-grained materials fabricated by severe plastic deformation[J].Mater Rev,2005,19(4):70(in Chinese).
陈勇军,王渠东,彭建国,等. 大塑性变形制备细晶材料的研究、开发及展望[J].材料导报,2005,19(4):70.
25 Peng Yonghui. Microstrcture,texture evolution and super- plasticity of Mg-1.5Mn-0.3Ce magnesium alloy processed by severe plastic deformation [D]. Guangzhou:South China University of Technology,2010(in Chinese).
彭勇辉.剧塑性变形Mg-1.5Mn-0.3Ce镁合金的组织与织构演变及超塑性[D].广州:华南理工大学,2010.
26 Cao Fenghong,Chen Yungui,Long Siyuan.Effect of textrue and grain size on mechanical properties of AZ61 magnesium alloy gdu-ring close-die hot-pressing of extruded performs[J].Special Cast Nonferrous Alloys,2016,36(3):242(in Chinese).
曹凤红,陈云贵,龙思远.织构和晶粒对挤锻复合成形AZ61镁合金力学性能的影响[J].特种铸造及有色合金,2016 36(3):242.