活性剂对A-TIG接头熔深、电弧形貌及组织性能的影响

doi:10.11896/cldb.23120053

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (26207KB)
Export: BibTeX | EndNote (RIS)

Abstract 1Cr21Ni5Ti stainless steel of 10 mm thick was selected as the research object, and the weld with the maximum penetration depth was obtained by optimizing the activator ratio and process parameters. The effect of activator on the arc morphology, microstructure and properties of A-TIG joints was studied. Compared to the joints obtained by traditional TIG, the joints obtained by A-TIG had a 122% increase in penetration depth, the arc undergoed significant contraction, the microstructure of the weld was refined, the content of austenite increased, and the width of heat affected zone significantly narrowed. The tensile strength of the joint obtained by A-TIG was as high as 702 MPa, which was 53.9% higher than the strength of the TIG joint, which was equivalent to 96.8% of the base metal. The joint failed in the center of the weld, which was caused by the addition of oxide activator, formed slag inclusions, and the fracture mode was ductile fracture.

Key words： A-TIG activator penetration depth strength fracture

Published: 10 January 2025 Online: 2025-01-10

CLC number:

TG444

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LIU Yuanhao
	REN Changjing
	XIANG Yanjun
	YUE Shiqi
	NI Yu
	ZHANG Pengxian
	HUANG Yong
	HUANG Jiankang

Cite this article:

LIU Yuanhao,REN Changjing,XIANG Yanjun, et al. Influence of Activator on the Penetration Depth, Arc Morphology, Microstructure and Properties of A-TIG Joints[J]. Materials Reports, 2025, 39(1): 23120053-5.

URL:

https://www.mater-rep.com/EN/10.11896/cldb.23120053 OR https://www.mater-rep.com/EN/Y2025/V39/I1/23120053

1 An L C, Cao J, Zhang T, et al. Materials and Corrosion, 2017, 68, 1116.
2 Soltani H M, Tayebi M. Journal of Alloys and Compounds, 2018, 767, 112.
3 Liu Z, Zhou X, Zhu T, et al. Materials Reports, 2021, 35(S2), 353 (in Chinese).
刘自刚, 周晓静, 朱婷婷, 等. 材料导报, 2021, 35(S2), 353.
4 Huang Y, Zhao W, Zhang L. Materials Reports, 2017, 31(22), 70 (in Chinese).
黄勇, 赵文强, 张利尧. 材料导报, 2017, 31(22), 70.
5 Zheng T, Chao Y, Zou L, et al. Ordnance Material Science and Engineering, 2018, 41( 4), 82 (in Chinese).
曾涛, 晁耀杰, 邹龙江, 等. 兵器材料科学与工程, 2018, 41(4), 82.
6 Ren Z, Yang C, Song Y, et al. Hot Working Technology, 2020, 49(23), 12 (in Chinese).
任泽良, 杨成刚, 宋友民, 等. 热加工工艺, 2020, 49(23), 12.
7 Zhu J, Li J, Yang C, et al. Journal of Netshape Forming Engineering, 2022, 14(10), 105 (in Chinese).
朱嘉文, 李佳, 杨成刚, 等. 精密成形工程, 2022, 14(10), 105.
8 Sheng X, Deng P, Li Y. Electric Welding Machine, 2015, 45(12), 32 (in Chinese).
沈向前, 邓鹏, 李耀辉. 电焊机, 2015, 45(12), 32.
9 Fu Y, Ren Z, Xiao Z, et al. Welding & Joining, 2020(4), 56 (in Chinese).
付彧, 任泽良, 肖中, 等. 焊接, 2020(4), 56.
10 Fan D, Liu Z, Huanng Y, et al. Transactions of the China Welding Institution, 2014, 35(4), 113 (in Chinese).
樊丁, 刘自刚, 黄勇, 等. 焊接学报, 2014, 35(4), 113.
11 Tseng K H, Chen K L. Journal of Nanoscience and Nanotechnology, 2012, 12(8), 6359.
12 Li C, Shi Y, Gu Y, et al. RSC Advances, 2017, 7(85), 53941.
13 Wu B. The effect of activator on the arc characteristics and weld performance of 309S stainless steel TIG welding. Master's Thesis, Southwest Petroleum University, China, 2016 (in Chinese).
武斌. 活性剂对309S不锈钢TIG焊电弧特性及焊缝性能的影响. 硕士学位论文, 西南石油大学, 2016.
14 Vidyarthy R S, Kulkarni A, Dwivedi D K. Materials Science and Engineering:A, 2017, 695, 249.