热塑性纤维铺放构件的层间剪切强度及孔隙率

doi:10.11896/cldb.20040042

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (3172KB)
Export: BibTeX | EndNote (RIS)

Abstract The in-situ curing technology is applied in the thermoplastic fiber (AS4/PEEK, melting point temperature 343 ℃) placement, so the interlaminar property directly affect the mechanical properties of the thermoplastic composite component after placement. In this paper, accor-ding to the principle of uniform test method, the placement test and interlaminar property test were designed,the data of interlaminar shear strength and porosity were obtained. The cross-sectional laminates were observed by SEM, at the same time, the interlaminar shear strength and porosity of the thermoplastic fiber placement component were optimized. Results showed that, based on the performance test data of the placement test component, it is obtained that as the heating temperature and the placement pressure increase, the interlaminar shear strength increases and as the placement speed increases, the interlaminar shear strength decreases on the contrary; the porosity has a positive correlation with the placement speed and heating temperature, and decreases with the increase of the placement pressure. When the placement speed is 6.00 mm/s, the hot air temperature is 699.35 ℃ and the placement pressure is 539.94 N, the maximum interlaminar shear strength of the component was predicted to be 52.15 MPa; when the placement speed is 6.00 mm/s, the hot air temperature is 630.04 ℃ and the placement pressure is 530.00 N, the minimum porosity of component was predicted to be 1.98%. The final test results are basically consistent with the prediction results, which has a certain practical value for the application level of thermoplastic fiber in the manufacturing field of our country.

Key words： thermoplastic fiber interlaminar property interlaminar shear strength porosity placement component automatic placement

Published: 30 September 2021

CLC number:

TB332

Fund:This work was financially supported by the National Natural Science Foundation of China (51705266), National Digital Control Special Support Project(2014ZX04001091)and Science Foundation of Heilongjiang Province (QC2018072).

About author:: Zhongliang Cao, associate professor at School of Mechanical Engineering, Jiangsu University of Technology, obtained his master's degree in mechanical engineering from Harbin Institute of Technology in 2010 and a Ph.D. in mechanical engineering from Harbin Institute of Technology in 2019. His research interest includes composite placement process, variable angle trajectory planning, CAD/CAM, etc. He has published more than twenty articles and authorized six patents.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	CAO Zhongliang
	GUO Dengke
	LIN Guojun
	HAN Zhenyu
	FU Hongya

Cite this article:

CAO Zhongliang,GUO Dengke,LIN Guojun, et al. Interlaminar Shear Strength and Porosity of Thermoplastic Fiber Placement Component[J]. Materials Reports, 2021, 35(18): 18205-18209.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.20040042 OR http://www.mater-rep.com/EN/Y2021/V35/I18/18205

1 Du S Y.Acta Materiae Compositae Sinica, 2007, 24(1), 1 (in Chinese).
杜善义. 复合材料学报, 2007, 24(1), 1.
2 Morey B. Manufacturing Engineering, 2008, 8(4), 12.
3 Grant C G. SAMPE Journal, 2000, 36(4), 7.
4 Sun Y B, Li H F, Zhang B M.Aeronautical Science & Technology, 2016, 18(5), 7(in Chinese).
孙银宝, 李宏福, 张博明. 航空科学技术, 2016, 18(5), 7.
5 Ji G M, Yin Y H, Zheng Z. China Adhesives, 2016, 25(3), 52(in Chinese).
季光明, 殷跃洪, 郑正. 中国胶粘剂, 2016, 25(3), 52.
6 Guo Z R, Zhao Y, Zhang X, et al. China Building Waterproofing, 2016,18(12), 9(in Chinese).
郭增荣, 赵宇, 张新, 等. 中国建筑防水, 2016,18(12), 9.
7 Mohammad R,Michael S. Journal of Composite Science, 2018, 2, 42.
8 Lionetto F, Dell' Anna R, Montagna F. Composites part A: Applied Science and Manufacturing, 2016, 82, 119.
9 Wen L W, Xiao J, Wang X F, et al. Journal of Nanjing University of Aeronautics and Astronautics, 2015, 47(5), 637 (in Chinese).
文立伟, 肖军, 王显峰, 等. 南京航空航天大学学报, 2015, 47(5), 637.
10 Lukaszewicz D, Ward C, Potter K. Composites Part B: Engineering, 2012, 43(3), 997.
11 Pedro R, Hamed A, Andrzej T, et al. Journal of Composite Materials, 2013(1), 17.
12 Bruce M. Manufacturing Engineering, 2008, 140(4), 6.
13 Dakai B, Bradley R, Shim D J, et al. Journal of Manufacturing Science and Engineering, 2017, 139(7), 29.
14 Wood K. High-Performance Composites, 2014, 22(1), 25.
15 Grouve W, Warnet L, Akkermanl R. International Journal of Material Forming, 2010(3), 710.
16 Lukaszewicz D, Potter K. International Technical Conference Advanced Composites, 2011(5), 126.
17 Muhammad A, Peter M, Ralf S. Journal of Composite Materials, 2012, 47(4), 485.
18 Muhammad A, Peter M, Ralf S. Advances in Polymer Technology, 2010, 29(2), 98.
19 Stokes C, Compston P. Composites part A: Applied Science and Manufacturing, 2016(88), 190.
20 Stokes C, Compston P. Composites part A: Applied Science and Manufac-turing, 2016(84), 17.
21 Stokes C, Compston P. Composites: Part A, 2015, 75, 104.
22 Tannous M, Barasinski A, Binetruy C. Journal of Materials Processing Technology, 2016, 29, 587.
23 Song Q H, Liu W P, Xiao J, et al.Acta Materiae Compositae Sinica, 2018, 35(5), 1149 (in Chinese).
宋清华, 刘伟平, 肖军, 等. 复合材料学报, 2018, 25(5), 32.
24 Qureshi Z, Swait T, Scaife R.Composites: Part B, 2014(66), 255.