0Cr25Ni7Mo4N双相不锈钢高温热塑性及组织演变

doi:10.11896/j.issn.1005-023X.2018.10.013

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (5896KB)
Export: BibTeX | EndNote (RIS)

Abstract The present work investigated the hot deformation behavior of two types of austenite-ferrite duplex stainless steels 0Cr25Ni7Mo4N, which differed in oxygen and nitrogen contents, via a hot tensile test within the temperature range of 1 000 ℃ to 1 200 ℃ and at the strain rate of 1 s^-1. The microstructures and inclusions were determined by optical microscope (OM), scanning electron microscope (SEM) and transmission electron microscope (TEM). The results showed that the steel deoxidized by aluminum and ferrosilicon (i.e. steel with relatively low oxygen and nitrogen contents) performs favorable thermoplasticity, while the undeoxidized steel with more oxygen and nitrogen exhibits good thermoplasticity only at above 1 150 ℃. This indicated the hot working temperature should be controlled above 1 150 ℃. The softening mechanism during the hot working process is the recovery of ferrite and the dynamic recrystallization of austenite. It can be concluded that the reasons for the low thermoplasticity of high-O, N-content steel are: the decline of binding strength at phase boundary induced by the precipitated coarse oxide inclusions containing chromium; the inappropriate ratio of austenite and ferrite phase.

Key words： 0Cr25Ni7Mo4N duplex stainless steel high-temperature tension thermoplasticity microstructure inclusion

Published: 06 July 2018

CLC number:	TG337.5
	TG142.71

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	LU Chengzhuang
	LI Jingyuan
	GAO Zhijun
	ZHANG Tairan
	CHEN Yulai
	WANG Yide

Cite this article:

LU Chengzhuang,LI Jingyuan,GAO Zhijun, et al. Thermoplasticity and Microstructure Evolution of Duplex Stainless Steel 0Cr25Ni7Mo4N Subjected to High-temperature Tensile Deformation[J]. Materials Reports, 2018, 32(10): 1639-1644.

URL:

http://www.mater-rep.com/EN/10.11896/j.issn.1005-023X.2018.10.013 OR http://www.mater-rep.com/EN/Y2018/V32/I10/1639

1 吴玖,姜世振.双相不锈钢[M].北京:冶金工业出版社,1999.
2 Cui Z, Wang L, Ni H, et al. Influence of temperature on the electrochemical and passivation behavior of 2507 super duplex stainless steel in simulated desulfurized flue gas condensates [J]. Corrosion Science,2017,118:31.
3 Yu S R, Meng K, Li S X. Fatigue properties of duplex stainless steel SAF2507 under air and corrosive environments [J]. Journal of Materials Engineering,2015,43(1):77(in Chinese).
俞树荣,孟恺,李淑欣.空气和腐蚀环境下双相不锈钢SAF2507的疲劳性能[J].材料工程,2015,43(1):77.
4 Dehghan-Manshadi A, Hodgson P D. Effect of δ-ferrite co-existence on hot deformation and recrystallization of austenite [J]. Journal of Materials Science,2008,43(18):6272
5 Chen Y L, Zhang T R, Wang Y D, et al. Effect of O, N, and Ni contents on hot plasticity of 0Cr25Ni7Mo4N duplex stainless steel[J]. Acta Metallurgical Sinica,2014,50(8):905(in Chinese).
陈雨来,张泰然,王一德,等.O,N和Ni含量对0Cr25Ni7Mo4N双相不锈钢热轧塑性的影响[J].金属学报,2014,50(8):905.
6 Feng Z, Li J. Mechanism of hot-rolling crack formation in lean duplex stainless steel 2101[J]. International Journal of Minerals, Me-tallurgy, and Materials,2016,23(4):425.
7 Tavares S S M, De Noronha R F, Da Silva M R, et al. 475 C embrittlement in a duplex stainless steel UNS S31803[J]. Materials Research,2001,4(4):237.
8 Hernandez-Castillo L E, Beynon J H, Pinna C, et al. Micro-scale strain distribution in hot-worked duplex stainless steel[J]. Steel Research International,2005,76(2-3):137.
9 Park J Y, Ahn Y S. Effect of Ni and Mn on the mechanical properties of 22Cr micro-duplex stainless steel[J]. Acta Metallurgica Sinica (English Letters),2015,28(1):32.
10 Kingklang S, Uthaisangsuk V. Investigation of hot deformation behavior of duplex stainless steel grade 2507[J]. Metallurgical and Materials Transactions A,2017,48(1):95.
11 Evangelista E, McQueen H J, Niewczas M, et al. Hot workability of 2304 and 2205 duplex stainless steels[J]. Canadian Metallurgical Quarterly,2004,43(3):339.
12 Cizek P, Wynne B P. A mechanism of ferrite softening in a duplex stainless steel deformed in hot torsion[J]. Materials Science and Engineering: A,1997,230(1-2):88.
13 Pinol-Juez A, Iza-Mendia A, Gutierrez I. δ/γ Interface bondary sli-ding as a mechanism for strain accommodation during hot deformation in a duplex stainless steel[J]. Metallurgical and Materials Transactions A,2000,31(6):1671.
14 Silverstein R, Eliezer D. Hydrogen trapping energy levels and hydrogen diffusion at high and low strain rates (~10⁵ s^-1 and 10^-7 s^-1) in lean duplex stainless steel [J]. Materials Science and Engineering: A,2016,674:419.
15 Martin G, Yerra S K, Bréchet Y, et al. A macro-and micromecha-nics investigation of hot cracking in duplex steels[J]. Acta Materialia,2012,60(11):4646.
16 Feng Z H, Li J Y, Wang Y D. Equilibrium solid solubility of nitrides in matrix of lean stainless steel 2101 [J]. Chinese Journal of Engineering,2016,38(12):1755(in Chinese).
冯志慧,李静媛,王一德.经济型双相不锈钢2101中氮化物在基体中的平衡固溶度计算[J].工程科学学报,2016,38(12):1755.
17 Song Z, Zheng W, Han F, et al. Hot ductility of DSS and Its microstructure observation during hot deformation[J]. Journal of Iron and Steel Research, International,2013,20(8):83.
18 刘雅政,任学平,王自东,等.材料成形理论基础[M].北京:国防工业出版社,2004.