| METALS AND METAL MATRIX COMPOSITES |
|
|
|
|
|
| Effect of Structural Parameters of Particle Reinforced Bonding Process on Bonding Strength and Process Optimization |
| QIN Yixin, ZENG Kai*, XING Baoying, ZHANG Hongshen, HE Xiaocong
|
| Faculty of Mechanical and Electrical Engineering, Kunming University of Science and Technology, Kunming 650500, China |
|
|
|
|
Abstract Box-Behnken design (BBD) method was used to investigate the effect of process parameters on the mechanical properties of particle reinforced adhesive bonded joints. The multivariate regression models between structural parameters of the adhesive layer (adhesive layer thickness, particle size, and particle volume fraction) and response values (failure load, energy absorption value) were established. Meanwhile, the multi-objective genetic algorithm was used to carry out multi-objective optimization of the bonding process, and the optimized parameters were verified by experiments. The results indicate that particle volume fraction has the biggest impact on the strength of the joints in single factor analysis, and the interaction of adhesive layer thickness and particle volume fraction have the highest influence on the strength of the joints. The optimum structural parameters of the adhesive layer are determined by Pareto solution set: adhesive layer thickness of 0.531 mm, particle size of 61.765 μm, and particle volume fraction of 4.099%. The errors between the predicted value and the real value are 5.7% (failure load) and 0.9% (energy absorption value), respectively.
|
|
Published: 25 March 2024
Online: 2024-04-07
|
|
|
| Fund:National Natural Science Foundation of China (51565022, 52065034). |
|
Corresponding Authors:
*kmzk201109@163.com
|
|
|
1 He X C. International Journal of Adhesion and Adhesives, 2014, 48, 59.
2 Zou T C, Qin J X, Li L H, et al. Materials Reports B: Research Papers, 2020, 34(10), 20143(in Chinese).
邹田春, 秦嘉徐, 李龙辉, 等. 材料导报:研究篇, 2020, 34(10), 20143.
3 Karthikeyan L, Robert T M, Mathew D, et al. International Journal of Adhesion and Adhesives, 2021, 106, 102816.
4 Liu W, Chen K P, Zhao X L. Journal of Chongqing Technology and Business University(Natural Science Edition), 2022, 39(3), 1(in Chinese).
刘文, 陈可平, 赵秀丽. 重庆工商大学学报(自然科学版), 2022, 39(3), 1.
5 Dorigato A, Pegoretti A. Journal of Nanoparticle Research, 2011, 13, 2429.
6 Jouyandeh M, Jazani O M, Navarchian A H, et al. Journal of Reinforced Plastics and Composites, 2016, 35, 1685.
7 Saraç İ, Adin H, TemizŞ. Composites Part B, 2018, 155, 92.
8 Bazrgari D, Moztarzadeh F, Sabbagh-Alvani A A, et al. Ceramics International, 2018, 44, 1220.
9 Khashaba U, Othman R, Najjar I M. Proceedings of the Institution of Mechanical Engineers, Part G: Journal of Aerospace Engineering, 2020, 234, 490.
10 Mishra S K, Shukla D K, Patel R K. Materials Research Express, 2020, 6, 1250i9.
11 Kaybal H B, Ulus H, Demir O, et al. Engineering Science and Technology: an International Journal, 2018, 21, 399.
12 Bai D P, He Y Y, Li T, et al. Journal of Xi'an Jiaotong University, 2021, 55(4), 181(in Chinese).
白德鹏, 贺云逸, 李亭, 等. 西安交通大学学报, 2021, 55(4), 181.
13 Gude M R, Prolongo S G, Ureña A. Surface and Coatings Technology, 2012, 207, 602.
14 Yoshinobu N, Miho Y, Akiko K, et al. Polymer, 1991, 32, 2221.
15 Deb K, Agrawal S, Pratap A, et al. IEEE Transactions on Evolutionary Computation, 2002, 6, 182.
16 Nastasi G, Colla V, Cateni S, et al. Journal of Intelligent Manufactu-ring, 2018, 29, 1545. |
|
|
|
渝公网安备50019002502923号 © Editorial Office of Materials Reports.
2024, Vol. 38 
