离心铸造双金属环件热辗扩实验研究

doi:10.11896/cldb.21110004

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (26803KB)
Export: BibTeX | EndNote (RIS)

Abstract Compared with the single metal ring, the bimetal ring has great advantages. It has two different metal with different properties to meet the different requirements for the inner and outer layers of the ring at the same time. Aiming at the problems of time-consuming, labor-intensive and poor bonding effect in the current manufacture of bimetallic rings, the authors proposes and studies a short-process manufacturing technology for bimetallic composite rings. In this process, two metals are joined together by centrifugal casting to form an annular billet, which is then hot rolled into a bimetallic ring. The method has the advantages of high production efficiency, energy saving, and good bonding layer. Based on the centrifugal casting bimetallic ring billets (inner layer Q345, outer layer 40Cr), ring rolling experiments were carried out at different initial rolling temperatures (1 200 ℃, 1 150 ℃, 1 050 ℃) and different rolling ratios (2.3, 2.0, 1.5). Metallographic and tensile experiments were performed on these rings. With the increase of rolling ratio, the grain size of the ring first became smaller and then larger, and the tensile strength first increased and then decreased. With the increase of rolling ratio, the grain size of the ring first became smaller and then larger, and the tensile strength first increased and then decreased. The bonding layer is a transition region with no obvious boundaries and its grains are larger than those of inner and outer layers. With the decrease of initial rolling temperature, the tensile strength increases first and then decreases, and the plasticity increases. All the ovality of rolled rings are less than 0.02, and no crack is detected by ultrasonic. When the initial rolling temperature is 1 050 ℃ and the rolling ratio is 2.3, the comprehensive performance of the ring is the best. The bimetallic ring of centrifugal casting has good shape, no crack defect, and its microstructure and mechanical properties have been improved after rolling. The casting and rolling compound forming of bimetallic ring is realized successfully.

Key words： bimetallic ring rolling temperature rolling ratio microstructure mechanical property

Published: 25 July 2023 Online: 2023-07-24

CLC number:

TG331

Fund:National Natural Science Foundation of China(51875383)and Research Project Supported by Shanxi Scholarship Council of China(2021-140).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	CHANG Yaodong
	QI Huiping
	JIA Yanlong
	YANG Kaifeng
	PEI Qinglin
	XIONG Bo

Cite this article:

CHANG Yaodong,QI Huiping,JIA Yanlong, et al. Experimental Research on Hot Ring Rolling of Centrifugally Cast Bimetallic Rings[J]. Materials Reports, 2023, 37(14): 21110004-8.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.21110004 OR http://www.mater-rep.com/EN/Y2023/V37/I14/21110004

1 Wang C W. Research on cold rolling forming technology of bimetal composite bearing ring. Master’s Thesis, University of Ningbo, China, 2018 (in Chinese).
王成威. 双金属复合材料轴承套圈冷辗扩成形技术研究. 硕士学位论文, 宁波大学, 2018.
2 Qin F C, Qi H P, Li Y T, et al. Materials Reports, 2020, 34(19), 19152 (in Chinese).
秦芳诚, 齐会萍, 李永堂, 等. 材料导报, 2020, 34(19), 19152.
3 Qin F C, Qi H P, Li Y T, et al. Materials Reports, 2021, 35(9), 9049 (in Chinese).
秦芳诚, 齐会萍, 李永堂, 等. 材料导报, 2021, 35(9), 9049.
4 Qi H P, Li Y T, Hua L, et al. Journal of Mechanical Engineering, 2014, 50(14), 75 (in Chinese).
齐会萍, 李永堂, 华林, 等. 机械工程学报, 2014, 50(14), 75.
5 Zhu S A, Yang H, Guo L G, et al. The International Journal of Advanced Manufacturing Technology, 2014, 72(1), 57.
6 Liang L, Guo L G, Liu Z H, et al. Journal of Materials Processing Technology, DOI: 10. 1016/j. jmatprotec. 2022. 117628.
7 Yang H, Wang M, Guo L G, et al. Computational Materials Science, 2008, 44(2), 611.
8 Li X C, Guo L G, Wang Y F, et al. Manufacturing Review, 2019, 6, 20.
9 Qin F C, Li Y T, Qi H P, et al. Advanced Materials and Processes, DOI:10. 4028/www. scientific. net/AMM. 395-396. 930.
10 Qin F C, Qi H P, Liu C Y, et al. Advances in Materials Science and Engineering, DOI:10. 1155/2021/6638505.
11 Chen Y Y, Qi H P, Li Y T, et al. Advances in Materials Science and Engineering, DOI:10. 1155/2021/9120018.
12 Qin F C, Qi H P, Li Y T. Materials Reports, 2020, 34(12), 12132 (in Chinese).
秦芳诚, 齐会萍, 李永堂, 等. 材料导报, 2020, 34(12), 12132.
13 Qin F C, Li Y T, Qi H P, et al. China Metalforming Equipment & Manufacturing Technology, 2015, 50(4), 78 (in Chinese).
秦芳诚, 李永堂, 齐会萍, 等. 锻压装备与制造技术, 2015, 50(4), 78.
14 Pei M M, Qi H P, Qing F C, et al. Special Casting and Non-ferrous Alloy, 2021, 41(8), 1031 (in Chinese).
裴蒙蒙, 齐会萍, 秦芳诚, 等. 特种铸造及有色合金, 2021, 41(8), 1031.
15 Yang C, Qin F C, Qi H P, et al. Forging & Stamping Technology, 2021, 46(3), 208 (in Chinese).
杨超, 秦芳诚, 齐会萍, 等. 锻压技术, 2021, 46(3), 208.
16 Zhou M X, Zhou S M, Zhang W S, et al. Hot Working Technology, 2020, 49(4), 122 (in Chinese).
周明星, 周世明, 张万顺, 等. 热加工工艺, 2020, 49(4), 122.
17 Liu Z C, Ji Y P, Ren H P, et al. Heat Treatment, 2008(4),19(in Chinese).
刘宗昌, 计云萍, 任慧平, 等. 热处理, 2008(4), 19.
18 Liu X G. Study on widmanstatten structure in microallying steel of Q460E. Ph. D. Thesis, China Academy of Railway Sciences, China, 2011 (in Chinese).
刘鑫贵. Q460E微合金化钢中魏氏组织的研究. 博士学位论文, 中国铁道科学研究院, 2011.
19 Lin W, Zhang X W, Zhao Y K, et al. Materials Science and Technology. 2009, 17(2), 247 (in Chinese).
林武, 张希旺, 赵延阔, 等. 材料科学与工艺, 2009, 17(2), 247.
20 Zhao Z M. Science and Technology Innovation Herald, 2016, 13(5), 34 (in Chinese).
赵志明. 科技创新导报, 2016, 13(5), 34.
21 Yao M, Fan Y L. Materials Science and Technology, 1986(3), 43 (in Chinese).
姚枚, 范莹隆. 金属科学与工艺, 1986(3), 43.
22 Huang Z, Yao M, Fan Y L, et al. Acta Metallurgica Sinica, 1987(3), 223 (in Chinese).
黄正, 姚枚, 范莹龙, 等. 金属学报, 1987(3), 223.
23 Huang Z, Yao M. Iron & Steel, 1990(4), 56 (in Chinese).
黄正, 姚枚. 钢铁, 1990(4), 56.
24 Yao S C, Ding Y, Zhao H, et al. Materials Reports, 2020, 34(S1), 452 (in Chinese).
姚三成, 丁毅, 赵海, 等. 材料导报, 2020, 34(S1), 452.
25 Ding Sheng, Taylor Tom,Khan Sabrina Alam, et al. Journal of Materials Processing Tech, 2021, 299, 117359.
26 Pan L B, Chu T, Zhang S, et al. Heat Treatment of Metals, 2021, 46(7), 23 (in Chinese).
潘龙博, 储滔, 张硕, 等. 金属热处理, 2021, 46(7), 23.
27 Pei M M. Study on thermal deformation and microstructure evolution behavior of 40Cr/Q345B bimetallic in centrifugal casting. Master’s Thesis, Taiyuan University of Science and Technology, China, 2021 (in Chinese).
裴蒙蒙. 离心铸造40Cr/Q345B双金属的热变形及组织演变行为研究. 硕士学位论文, 太原科技大学, 2021.
28 Qin F C, Qi H P, Li Y T, et al. Journal of Mechanical Engineering, 2017, 53(2), 26 (in Chinese).
秦芳诚, 齐会萍, 李永堂, 等. 机械工程学报, 2017, 53(2), 26.
29 Fan Y L. Journal of Xiangtan University Natural Science Edition, 1992(3), 44 (in Chinese).
范莹隆. 湘潭大学自然科学学报, 1992(3), 44.