AZ80A、ZK60A和ME20M镁合金干摩擦学性能研究

doi:10.11896/cldb.20050164

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (6373KB)
Export: BibTeX | EndNote (RIS)

Abstract Magnesium alloys were widely used in the aerospace, automotive and military fields, and the reliability and service life of moving parts of magnesium alloys depended on their tribological properties. In this paper, the tribological behavior of AZ80A, ZK60A and ME20M magne-sium alloys was tested by using a reciprocating ball-on-disk tribometer sliding against GCr15 steel ball under dry-sliding condition at different applied loads and sliding speeds. The wear mechanisms of magnesium alloys were analyzed by the scanning electron microscope and energy spectrometer at different loads and speeds. The results showed that the friction coefficients of alloys gradually decreased with the increase of sliding speed when the sliding speed exceeded 0.10 m/s. However, the wear rates decreased, and then increased. It was ascribed to the low shear force and formation of oxides on the worn surfaces due to the friction heat. When the sliding speed reached up to 0.20 m/s, the metal oxides peeled off from the surface in order to increase the wear rates of alloys because of the elevated temperature. The friction coefficients and wear rates of alloys increased as the applied loads increased. The wear mechanisms of magnesium alloys transferred from the abrasive wear and plastic deformation to the abrasive wear, oxidative wear, adhesive wear and plastic deformation under dry-sliding condition. The AZ80A alloy showed the good tribological properties as compared with ZK60A and ME20M alloys. It was ascribed to the high hardness, β-Mg₁₇Al₁₂ hard phase and metal oxides on the contacting surfaces.

Key words： magnesium alloys dry-sliding friction wear

Published: 04 June 2021

CLC number:

TH117.1

Fund:National Natural Science Foundation of China (51775365), the National Natural Science Foundation Youth Fund of China (51405329).

About author:: Gongjun Cui, professor of Taiyuan University of Technology, mainly engaged in tribology, composites, alloys and other fields of research. He has undertaken a number of national and provincial projects, including the National Natural Science Foundation of China (51775365, 51405329), China Postdoctoral Science Foundation (2015M570239) and so on. He has published more than 50 papers in academic journals at home and abroad.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	CUI Gongjun
	SHI Ruibo
	LI Sai
	LIU Huiqiang
	KOU Ziming

Cite this article:

CUI Gongjun,SHI Ruibo,LI Sai, et al. Study on the Tribological Properties of AZ80A, ZK60A and ME20M Magnesium Alloys Under Dry-sliding Condition[J]. Materials Reports, 2021, 35(10): 10103-10108.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.20050164 OR http://www.mater-rep.com/EN/Y2021/V35/I10/10103

1 Lei Y, Yan H G, Chen J H, et al.Materials Reports B:Research Papers, 2020, 34(1), 2067(in Chinese).
雷意,严红革,陈吉华,等. 材料导报:研究篇, 2020, 34(1), 2067.
2 Wang C M, Yang M N, Huang J H, et al.Materials Reports A:Review Papers, 2019, 33(7), 2260 (in Chinese).
王春明,杨牧南,黄建辉,等.材料导报:综述篇, 2019, 33(7), 2260.
3 You G Q, Guo W, Zhang X L, et al.Journal of Materials Engineering, 2018, 46(1), 141 (in Chinese).
游国强, 郭伟, 张秀丽, 等. 材料工程, 2018, 46(1), 141.
4 An J, Li R G, Lu Y, et al.Wear, 2008, 265(1), 97.
5 Hu H J, Sun Z, Ou Z W, et al. Engineering Failure Analysis, 2017, 72, 25.
6 Li, H, Lu S T, Qin W, et al. Acta Astronautica, 2015, 116, 126.
7 Huang S J, Aqeel A, Beáta B.Journal of Materials Research and Techno-logy, 2019, 8(5), 4273.
8 Zafari A, Ghasemi H M, Mahmudi R.Wear, 2013, 303(1-2), 98.
9 Tazegul O, Muhaffel F, Meydanoglu O, et al.Surface and Coatings Technology, 2014, 258, 168.
10 Chen B X, Chen W.Materials Protection, 2019, 52(5), 44 (in Chinese).
陈斌星, 陈伟.材料保护, 2019, 52(5), 44.
11 Cao Z, Wang X D, Dong J, et al.Chinese Journal of Rare Metals, 2018, 42(2), 139 (in Chinese).
曹振, 王旭东, 董杰, 等. 稀有金属, 2018, 42(2), 139.
12 Hadadzadeh A, Wells M A, Shaha S K, et al. Journal of Alloys and Compounds, 2017, 702, 274.
13 Zhang T F, Huang J H, Deng M, et al.Forging & Stamping Technology, 2006(6), 40 (in Chinese).
张庭芳, 黄菊花, 邓敏, 等. 锻压技术, 2006(6), 40.
14 Li Y, Zhang Z M,Xue Y.Transactions of Nonferrous Metals Society of China, 2011, 21(4), 739.
15 Xie B W, Sha G Y, Dong G Y, et al.Light Alloy Fabrication Technology, 2019, 47(3), 53 (in Chinese).
谢博文, 沙桂英, 董庚益, 等. 轻合金加工技术, 2019, 47(3), 53.
16 Guo Y Y, Lin Z X, Jiang H Y, et al.The Chinese Journal of Nonferrous Metals, 2011, 21(1), 58 (in Chinese).
郭言炎, 林志埙, 蒋海燕, 等. 中国有色金属学报, 2011, 21(1), 58.
17 Chen Z, Zhang M L, Lyu Y Z, et al.Foundry Technology, 2007,28(6), 820 (in Chinese).
陈增, 张密林, 吕艳卓, 等. 铸造技术, 2007, 28(6), 820.
18 Dahle A K, Lee Y C, Nave M D, et al.Journal of Light Metals, 2001, 1(1), 61.
19 Barnett M R, Nave M D, Bettles C J.Materials Science & Engineering A, 2004, 386(1-2), 205.
20 Aung N N, Zhou W, Lim Lennie E N. Wear, 2008, 265(5), 780.
21 Wang J H, Teng C Y, Li X Q, et al.Materials Reports, 2017, 31(S2), 367 (in Chinese).
王金辉, 腾朝艳, 李小强, 等. 材料导报, 2017, 31(专辑30), 367.
22 Bi Q L, Liu W M, Ma J Q, et al.Tribology International, 2009, 42, 1081.
23 Huang W J, Hou B, Pang Y X, et al.Tribology, 2005, 25(3), 225 (in Chinese).
黄伟九, 侯滨, 庞佑霞, 等. 摩擦学学报, 2005, 25(3), 225.
24 Taltavull C, Rodrigo P, Torres B, et al.Materials and Design, 2014, 56, 549.
25 Hu M L, Wang Q D, Li,C, et al.Transactions of Nonferrous Metals Society of China, 2012, 22(8), 1918.
26 Chen Q Q, Liu Y Y, Zhao Z H, et al.Journal of Northeastern University (Natural Science), 2017, 38(11), 1554 (in Chinese).
陈庆强, 刘宇洋, 赵志浩, 等. 东北大学学报(自然科学版),2017, 38(11), 1554.
27 Hui Y, Liu G M, Yan T, et al.Surface Technology, 2019, 48(10), 196 (in Chinese).
惠阳, 刘贵民, 闫涛, 等. 表面技术, 2019, 48(10), 196.
28 Chen L,Zhang X M, Liu F, et al.Journal of Chongqing Technology and Business University(Natural Science Edition),2017,34(1),75(in Chinese).
陈凌, 张贤明, 刘飞, 等.重庆工商大学学报(自然科学版),2017,34(1),75.