METALS AND METAL MATRIX COMPOSITES |
|
|
|
|
|
Fabrication of Gradient Semi-solid 9Cr18 Stainless Steel and the Microstructure Evolution |
WANG Yongjin, ZHANG Yingchao, SONG Renbo
|
School of Materials Science and Engineering,University of Science and Technology Beijing,Beijing 100083, China |
|
|
Abstract In this paper, a semi-solid thixoforging set-up was designed based on Gleeble3500 thermomechanical machine. 9Cr18 thixoforging component was fabricated and the microstructure evolution was investigated. The results showed that the 9Cr18 semi-solid billet could demonstrated thi-xotropic behavior after the breakdown of solid skeleton and load decreased with the deformation during thixotropic stage. Gradient microstructure could be obtained for the 9Cr18 thixoforging specimen. An obvious solid/liquid interface existed near the edge area of thixoforging specimen. Eutectic structure with plenty of carbide could be seen outside the solid/liquid interface. Solid particles were mainly retained at the inner area. 9Cr18 thixoforging specimen demonstrated unique microstructure evolution. The solid particles at the inner area mainly showed austenite microstructure with excellent deformation behavior, while the hard M7C3 carbides existed at surface eutectic layer. This microstructure characterization contributed to the properties of tough center and hard surface.
|
Published: 28 January 2021
|
|
Fund:The China Postdoctoral Science Foundation (2019M650482), the Fundamental Research Funds for the Central Universities (FRF-TP-18-039A1). |
About author:: Yongjin Wangreceived his Ph.D. degree in June 2018 from University of Science and Technology Beijing. From September 2016 to March 2018, he co-educated and learned at the University of Tokyo, focusing on the research of semi-solid processing of steel. |
|
|
1 Liu Y Z, Zhou L Y, Zhang C L, et al. Iron and Steel, 2013, 48(8), 1(in Chinese). 刘雅政,周乐育,张朝磊,等. 钢铁, 2013, 48(8), 1. 2 Sobczak J J, Drenchev L. Journal of Materials Science & Technology, 2013, 29(4), 297. 3 Fu Y, Zhang W, Xu X, et al. Metallurgical and Materials Transactions A, 2017, 48(9), 3975. 4 Lu K. Science, 2010, 328, 319. 5 Fang T H, Li W L, Tao N R, et al. Science, 2011, 331(6024), 1587. 6 Wang Y, Zhou F, Ma E, et al. Nature, 2002, 419(6910), 912. 7 Rassili A. Solid State Phenomena. 2016, 256, 228. 8 Midson S P. In: Semi-Solid Processing of Alloys and Composites XIII. Muscat, 2014, pp. 487. 9 Gu G C, Pesci R, Langlois L, et al. Acta Materialia, 2014, 66, 118. 10 Meng Y. Journal of Netshape Forming Engineering, 2016(4), 21(in Chinese). 孟毅. 精密成形工程, 2016(4), 21. 11 Xiao G, Jiang J, Liu Y, et al. Materials Characterization, 2019, 156, 109874. 12 Kareh K M, O′Sullivan C, Nagira T, et al. Acta Materialia, 2017, 125, 187. 13 Chen C P, Tsao C Y A. Acta Materialia, 1997, 45(5), 1955. 14 Solek K P, Rassili A, Pierret J C, et al. Transactions of Nonferrous Metals Society of China, 2010, 20, s916. 15 Wang S, Ji Z, Sugiyama S, et al. Materials & Design, 2015, 65, 591. 16 Payandeh M, Jarfors A E W, Wessen M. In: Semi-Solid Processing of Alloys and Composites XIII. Muscat, 2014, pp. 67. 17 Campo K N, de Freitas C C, Moon S, et al. Materials Characterization, 2018, 145, 10. 18 Meng Y, Sugiyama S, Yanagimoto J. Journal of Materials Processing Technology, 2012, 212(8), 1731. 19 Wang Y J, Song R B, Song R F. Acta Metallurgica Sinica, 2018, 54(1), 39(in Chinese). 王永金,宋仁伯,宋仁峰. 金属学报, 2018, 54(1), 39. 20 Gu G, Pesci R, Langlois L, et al. Journal of Materials Processing Tech-nology, 2015, 216, 178. 21 Ning X L, Tang X J. Aviation Maintenance & Engineering, 2017(6), 64(in Chinese). 宁新龙,唐秀娟. 航空维修与工程, 2017(6), 64. 22 Zhou Y, Liu Y, Zhou X, et al. Journal of Materials Science & Technology,2017, 33(12), 1448. 23 Wang Y, Song R, Li Y. Materials Characterization, 2017, 127, 64. 24 Wang Y, Song R, Li Y, et al. Materials Science Forum, 2015, 817, 278. |
|
|
|