激光熔覆修复对TC4钛合金疲劳裂纹扩展速率的影响

doi:10.11896/j.issn.1005-023X.2018.16.019

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (3380KB)
Export: BibTeX | EndNote (RIS)

Abstract To investigate the effect of laser clad repair on crack growth rate of TC4 titanium alloy, surface groove of TC4 titanium alloy plate was repaired by adding TC4 titanium power layer by layer based on laser cladding technology. The microstructure and fracture surface morphology were characterized by optical microscopy and scanning electron microscopy, respectively. Fatigue crack growth experiment was used to obtain the crack length and cycle number. A modified incremental polynomial method was used to obtain the fatigue crack propagation rates of three samples per group under the same crack length. Experimental results indicated that the laser repairing zone was composed of β grains and α phase precipitating along the grain boundary, which belonged to typical Widmannstatten. The heat effect zone consisted of equiaxed α grains and β transformed structure, which was known as two-state structure. Comparing with the original sample, the fatigue crack growth rate of the laser cladding repaired samples was obviously decreased. The improvement of fatigue crack growth rate resistance for laser cladding repaired TC4 titanium alloy was attributed to a combination of high fracture toughness of Widmannstatten and the comprehensive mechanical properties of two-state structure.

Key words： laser clad repair TC4 titanium alloy microstructure crack growth rate

Published: 18 September 2018

CLC number:	TN249
	TG115.5
	TG146.2

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	GE Maozhong
	XIANG Jianyun
	FAN Zhen

Cite this article:

GE Maozhong,XIANG Jianyun,FAN Zhen. Effect of Laser Clad Repair on Crack Growth Rate of TC4 Titanium Alloy[J]. Materials Reports, 2018, 32(16): 2803-2808.

URL:

http://www.mater-rep.com/EN/10.11896/j.issn.1005-023X.2018.16.019 OR http://www.mater-rep.com/EN/Y2018/V32/I16/2803

1 Chen J, Zhang Q, Liu Y H, et al. Research on microstructure and high-temperature properties of Ti17 titanium alloy fabricated by laser solid forming[J]. Chinese Journal of Lasers,2011,38(6):0603022(in Chinese).
陈静,张强,刘彦红,等.激光成形修复Ti17合金组织与高温性能研究[J].中国激光,2011,38(6):0603022.
2 Chen B, Shao B, Liu D, et al. Effect of heat treatment on microstructure and mechanical properties of laser melting deposited TC17 titanium alloy[J].Chinese Journal of Lasers,2014,41(4):0403001-1(in Chinese).
陈博,邵冰,刘栋,等.热处理对激光熔化沉积TC17钛合金显微组织及力学性能的影响[J].中国激光,2014,41(4):0403001-1.
3 He B W, Ran X Z, Tian X J, et al. Corrosion resistance research of laser additive manufactured TC11 titanium alloy[J]. Chinese Journal of Lasers,2016,43(4):0403004-1(in Chinese).
何博文,冉先喆,田象军,等.激光增材制造TC11钛合金的耐蚀性研究[J].中国激光,2016,43(4):0403004-1.
4 Gong X Y, Liu M K, Li Y, et al. Research on repair of TC11 tita-nium alloy components by laser melting deposition process[J]. Chinese Journal of Lasers,2012,39(2):0203005-1(in Chinese).
宫新勇,刘铭坤,李岩,等.TC11钛合金零件的激光熔化沉积修复研究[J].中国激光,2012,39(2):0203005-1.
5 《中国制造》编写组,著.中国制造2025[M].北京:人民出版社,2015.
6 黄卫东.激光立体成形[M].西安:西北工业大学出版社,2007:1.
7 Bontha S. The effect of process variables on microstructure in laser-deposited materials [D].Ohio: Wright State University,2006.
8 Gaumann M, Bezencon C, Canalis P, et al. Single-crystal laser de-position of superalloys: Processing-microstructure maps[J]. Acta Materialia,2001,49:1051.
9 Wang N, Mokadern S, Rappaz M, et al. Solidification cracking of super alloy single and bi-crystals[J]. Acta Materialia,2004,52:3173.
10 Bendeich P, Alam N, Brandt M, et al. Residual stress measurements in laser clad repaired low pressure turbine blades for the power industry[J]. Materials Science and Engineering A,2006,437:70.
11 Shi D S, Qian C L, Brandt M, et al. Effect of laser clad repair on the fatigue behavior of ultra-high strength AISI 4340 steel[J]. Materials Science & Engineering A,2014,606:46.
12 Xue L, Chen J, Lin X, et al. Low cycle fatigue property of laser forming repaired TC4 forgings[J]. Rare Metal Materials and Engineering,2011,40(7):1225(in Chinese).
薛蕾,陈静,林鑫,等.激光成形修复TC4合金锻件的低周疲劳性能[J].稀有金属材料与工程,2011,40(7):1225.
13 Zhu L W, Zhu Z S, Wang X N, et al. Influence of lamellar microstructure on fatigue crack propagation behavior of TC4-DT of da-mage tolerance[J].Journal of Aeronautical Materials,2011,31(S1):164(in Chinese).
祝力伟,朱知寿,王新南,等.不同片层组织对TC4-DT钛合金裂纹扩展行为的影响[J].航空材料学报,2011,31(S1):164.
14 Wu C Z,Li X W,Huang X,et al. Relationship of fatigue crack propagation and microstructure for TAl5 alloy[J]. Rare Metal Materials and Engineering,2007,36(12):2128(in Chinese).
吴崇周,李兴无,黄旭,等.TAl5钛合金疲劳裂纹扩展与显微组织的关系[J].稀有金属材料与工程,2007,36(12):2128.