GH4169旋转摩擦焊飞边成形机理研究

doi:10.11896/cldb.20030095

Abstract
Figure/Table
References
Related Citation (3)

Download:

Full Text ( PDF ) (5721KB)
Export: BibTeX | EndNote (RIS)

Abstract In this work, continuous-drive rotary friction welding was conducted on GH4169 rods in diameter of Φ25 mm to investigate the flash formation mechanism. The welding parameters were set as burn-off length 5 mm, welding pressure 200 MPa and rotation speed ranged as 500—2 500 r/min. The high-speed camera was installed to monitor the burn-off rate; whereas the infrared camera to collect the surface temperature of the joint. The joints were cut for interface morphology and microstructure observation by OM, SEM and EBSD. On the other hand, the calculation on friction heat liberation was modeled and conducted in Matlab environment, which is correlated by the experiment of interim stops on welding process that were carried out to reveal the transient morphology of the joint. The results tell that, the joint shows the flash appearance as smooth, ‘arcuate microcracked' and cracked consequently as the rotation speed is increased. The rotation speed was found a criterion at about 800 r/min, below which the joint presents smooth flash. When the rotation speed is around 800—1 500 r/min and over 1 500 r/min, ‘arcuate microcracked' and cracked flash occur consequently. Smooth flash corresponds to slower growth speed of the flash with longer growth time, which provides the conditions for recrystallization and softening when the metal is extruded to form flash. Whereas, ‘arcuate microcracked' and cracked flash correspond to faster speed and shorter time, where recrystallization has not been completed before work hardening and cracking during the flash formation. Moreover, different flash appearances correspond to different formation mechanisms. Smooth flash is the result of uniform flow and extrusion of plasticized metal, which is originated from the corona-bond initiating at middle to the edge (0.43R—R) of the interface and then extending. Whereas, ‘arcuate microcracked' and cracked flash are formed under rapid forging process of interface metal at welding temperature due to the lack of plasticized metal, which initiates at inner side of the interface (0—0.43R) and then is closed without flow under the normal stress. Different flashes make neglectable effects on local strength distribution of the joint but the elongation sampled at periphery. The smooth, ‘arcuate microcracked' and cracked flash correspond to 17%, 9% and 6% elongation sampled at periphery respectively, where the correspon-ding inhomogeneity of joint elongation increases from 8% to 50%, 66%.

Key words： nickel-based superalloy GH4169 rotary friction welding flash appearance corona-bond joint properties

Published: 26 April 2020

CLC number:

TG453

Fund:This work was financially supported by the Natural Science Foundation of China (51575451, 51475376).

Corresponding Authors: Jinglong Li, professor and doctoral supervisor of School of Materials Science and Engineering, Northwestern Polytechnical University. He is mainly engaged in the research of friction welding, diffusion bonding, brazing and thermal spraying.

About author:: Feng Jin, Ph.D candidate of engineering in Northwes-tern Polytechnical University. His research interests are the joint formation process and mechanism of solid-state welding such as rotary friction welding.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	JIN Feng
	XIONG Jiangtao
	SHI Junmiao
	GUO Delun
	LI Jinglong

Cite this article:

JIN Feng,XIONG Jiangtao,SHI Junmiao, et al. Flash Formation Mechanism During Rotary Friction Welding of GH4169 Superalloy[J]. Materials Reports, 2020, 34(10): 10144-10149.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.20030095 OR http://www.mater-rep.com/EN/Y2020/V34/I10/10144

1 Chen X M, Lin Y C, Chen M S, et al. Materials & Design, 2015, 77, 41.
2 Yang X W, Li W Y, Li J L, et al. Materials & Design, 2015, 84, 133.
3 Ning F Z, Cai Y X. Friction welding, Mechanical Industry Press, China, 1983(in Chinese).
宁斐章, 才荫先. 摩擦焊, 机械工业出版社, 1983.
4 Li W Y, Vairis A, Preuss M, et al. International Materials Reviews, 2016, 61(2),71.
5 Jin F, Li J L, Du Y J, et al. Journal of Manufacturing Processes, 2019, 45, 595.
6 Cai Y X, Sun S T, Zhu G Z, et al.Transactions of the China Welding Institution, 1984,5(2),57(in Chinese).
才荫先, 孙松涛, 朱桂芝, 等. 焊接学报, 1984,5(2), 57.
7 Bai X Y. Microstructure and mechanical properties of axial friction welded nickel-based superalloy GH4169. Master's Thesis, Shandong University, China, 2017(in Chinese).
白晓阳. GH4169镍基高温合金轴向摩擦焊接头微观组织与力学性能. 硕士学位论文,山东大学, 2017.
8 Nan X J. Heat liberation modelling of rotary friction welding process and numerical simulation on joint formation mechanism. Master's Thesis, Northwestern Polytechnical University, China, 2019(in Chinese).
南旭惊. 旋转摩擦焊产热模型与接头成形机制数值模拟. 硕士学位论文,西北工业大学, 2019.
9 Li F G, Zhang M C, Duan L Y, et al. Transactions of the China Wel-ding Institution, 2001, 22(4), 43(in Chinese).
李付国, 张敏聪, 段立宇, 等. 焊接学报, 2001, 22(4), 43.
10 Zhang Q Z. Numerical simulation of friction welding process of GH4169 superalloy. Ph.D. Thesis, Dalian University of Technology, China, 2007(in Chinese).
张全忠. GH4169合金摩擦焊接过程的数值模拟研究. 博士学位论文, 大连理工大学, 2007.
11 Ji S D, Liu J G, Zhang L G, et al. Transactions of the China Welding Institution, 2013, 34(4),31(in Chinese).
姬书得, 刘建光, 张利国, 等. 焊接学报, 2013, 34(4), 31.
12 Jin F, Li J L, Liu P, et al. Journal of Manufacturing Processes, 2019, 46, 286.
13 Maalekian M. Science and Technology of Welding and Joining, 2007, 12(8), 738.
14 Luo J, Chen H, Liu S S. Welding & Joining, 2017(1), 13(in Chinese).
罗键, 陈欢, 刘姗姗. 焊接, 2017(1), 13.
15 Li X, Li J L, Liao Z X, et al. Journal of Adhesion Science and Technology, 2018, 32(18), 1987.
16 Crossland B. Contemporary Physics, 2006, 12(6),559.