显微组织对贝氏体钢筋氢脆敏感性的影响

doi:10.11896/cldb.17090254

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (24470KB)
Export: BibTeX | EndNote (RIS)

Abstract The bars were widely used in many areas such as high speed road, high railway and bridge engineering. In this paper, the effect of microstructure on hydrogen embrittlement susceptibility of two strength grade of bainitic bars was investigated by electrochemical hydrogen charging tests and slow strain rate tensile tests, scanning electron microscopy (SEM), transmission electron microscope (TEM), X-ray diffraction (XRD) and electron back scatter diffraction patterns (EBSD). The results showed that microstructure had strong impact on hydrogen embrittlement susceptibility. Due to the appropriate alloying and microstructural designs, the strength of PSB1080 bars was much higher than that of PSB830 bars. However, it is surprising that the hydrogen embrittlement susceptibility of the PSB1080 bars was lower. The uneven distribution of hydrogen in PSB830 was mainly caused by the heterogeneous distribution of microstructure. The reason of higher hydrogen embrittlement susceptibility of PSB830 was that the martensite with high dislocation density was regard as the reversible hydrogen trap, therefore, a lot of hydrogen atoms were absorbed in the specimens. During tensile test, the hydrogen atoms were easy to diffuse and enrich. On contrary, the martensite and bainite with better coordinated deformation capability were uniform distribution in the PSB1080. The filmy retained austenite, which was located between laths, was seen as an irreversible hydrogen trap, so the diffusion and enrichment of hydrogen atom was hindered. At the same time, the filmy retained austenite also had high mechanical stability and chemical stability. Therefore, the hydrogen embrittlement susceptibility of PSB1080 bars was lower than PSB830 bars.

Key words： bainitic bars microstructure hydrogen embrittlement susceptibility reversible hydrogen trap retained austenite

Published: 16 May 2019

CLC number:

TG113.12

Fund:This work was financially supported by the National Key Basic Research Program of China (2015CB654804) and Beijing Municipal Natural Science Foundation (2172047).

About author:: Haoran Guo received his M.S. degree in materials science and engineering in April 2018 from Beijing Jiaotong University, focusing on the research of heat treatment of metallic materials.
Guhui Gao received his Ph.D. degree in materials science and engineering from Tsinghua Univeristy in 2013. He is currently an associate professor in Beijing Jiaotong University. His research interests are bainitic transformation and bainitic steels.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	GUO Haoran
	GAO Guhui
	GUI Xiaolu
	BAI Bingzhe

Cite this article:

GUO Haoran,GAO Guhui,GUI Xiaolu, et al. Effect of Microstructure on Hydrogen Embrittlement Susceptibility of Bainitic Bars[J]. Materials Reports, 2019, 33(10): 1717-1722.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.17090254 OR http://www.mater-rep.com/EN/Y2019/V33/I10/1717

1 Wang J. The Research of finished-rolled screw-thread steel bars continuous induction heat treatment and deformation control. Master's Thesis, Beijing Research Institute of Mechanical & Electrical Technology, China,2011 (in Chinese).
王劲. 高强精轧螺纹钢筋连续感应热处理及控制变形研究. 硕士学位论文, 北京机电研究所, 2011.
2 Sun Y W, Chen J Z, Liu J.Acta Metallurgica Sinica, 2015, 51(11), 1315 (in Chinese).
孙永伟, 陈继志, 刘军.金属学报, 2015, 51(11), 1315.
3 Li H L, Hui W J, Wang Y B, et al.Acta Metallurgica Sinica, 2001, 37(5), 512 (in Chinese).
李会录, 惠卫军, 王燕斌, 等.金属学报, 2001, 37(5),512.
4 Depover T, Monbaliu O, Wallaert E, et al.International Journal of Hydrogen Energy, 2015, 40(47), 16977.
5 Tian Y, Wang M Q, Li J X, et al.Acta Metallurgica Sinica, 2008, 44(4), 403 (in Chinese).
田野, 王毛球, 李金许, 等.金属学报, 2008, 44(4), 403.
6 Li J X, Wang Y B, Chu W Y, et al.Journal of Chinese Society for Corrosion and Protection, 1998, 18(2), 113 (in Chinese).
李金许, 王燕斌, 褚武扬, 等. 中国腐蚀与防护学报, 1998, 18(2), 113.
7 Zhang Y J, Zhou C, Hui W J, et al.Journal of Iron and Steel Research, 2014, 26(5), 49(in Chinese).
张永健, 周超, 惠卫军, 等.钢铁研究学报, 2014, 26(5), 49.
8 He J H, Tang X Y, Chen N P.Acta Metallurgica Sinica, 1990, 26(4), A257 (in Chinese).
何建宏, 唐祥云, 陈南平.金属学报, 1990, 26(4), A257.
9 Song Y J, Qi M.Acta Metallurgica Sinica, 1987, 23(3), 205 (in Chinese).
宋余九, 齐民. 金属学报,1987, 23(3), 205.
10 Yang F B, Bai B Z, Liu D Y, et al.Acta Metallurgica Sinica, 2004, 40(3), 296 (in Chinese).
杨福宝, 白秉哲, 刘东雨, 等. 金属学报, 2004,40(3), 296.
11 Gao K, Wang L D, Zhu M, et al.Acta Metallurgica Sinica, 2007, 43(3), 315 (in Chinese).
高宽, 王六定, 朱明, 等.金属学报, 2007, 43(3), 315.
12 Gui X L, Liu R, Gao G H, et al.Transactions of Materials and Heat Treatment, 2016, 37(10), 154 (in Chinese).
桂晓露, 刘蓉, 高古辉, 等.材料热处理学报, 2016, 37(10), 154.
13 Zhongqi Cui,Metallography and heat treatment, Mechanical Industry Press, China, 2007 (in Chinese).
崔忠圻.金属学与热处理, 机械工业出版社, 2007.
14 Zhang Q, Shi Q H.Foundry Technology, 2013, 34(5), 533 (in Chinese).
张勤, 石秋红.铸造技术,2013, 34(5), 533.
15 Wang Y, Zhang K, Guo Z H, et al.Acta Metallurgica Sinica, 2012, 48(6), 641 (in Chinese).
王颖,张柯,郭正洪, 等.金属学报, 2012,48(6), 641.
16 Gao G H, Zhang H, Gui X L, et al.Acta Materialia, 2014, 76, 425.
17 Chang K D. Study on mechanism of delayed fracture for Bainite/Marten-site dual-phase high strength steel.Ph.D. Thesis, Tsinghua University, China, 2002 (in Chinese).
常开地. 贝氏体/马氏体复相高强钢延迟断裂机理的研究.博士学位论文, 清华大学, 2002.
18 Yang Ping.Electron backscatter diffraction technology and its application, Mechanical Industry Press, China, 2013 (in Chinese).
杨平.电子背散射衍射技术及其应用,冶金工业出版社, 2013.
19 Luo J. The mechanism of hydrogen embrittlement and improvement method for Q-P-T steel. Master's Thesis, Shanghai Jiao Tong University, China, 2015 (in Chinese).
罗洁. Q-P-T钢的氢脆机制及其改善措施. 硕士学位论文, 上海交通大学, 2015.
20 Wu Q, Zikry M A.Journal of the Mechanics and Physics of Solids, 2015, 85, 143.
21 Zhu X, Zhang K, Li W, et al.Materials Science & Engineering A, 2016, 658, 400.