室温C-ECAP纯铝组织演变及强韧化机理研究

doi:10.11896/cldb.24050232

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (57014KB)
Export: BibTeX | EndNote (RIS)

Abstract Conventional ECAP is greatly limited in the continuous application of materials, so it is impossible to prepare longer bars. In this work, conti-nuous ECAP (C-ECAP) was used to extrude pure aluminum for four passes, and the effects of different passes on the microstructure, texture evolution, strength and hardness of pure aluminum were studied. The results showed that the initial grain size got refined from 47.9 μm to 1.1 μm, the microstructure distribution became more uniform, and the proportion of large-angle grain boundaries was increased from 5.9% to 12.6%. The deformed grains gradually transformed into sub-grains and recrystallized grains, and dynamic recrystallization reduced the dislocation density. The initial structure changed from coarse equiaxed grains to fine equiaxed grains. After 1-pass and 4-pass extrusion, the texture changed from {112}〈111〉 copper texture and {110}〈112〉 brass texture to {001}〈100〉 cube texture. The strength and hardness increased significantly, as the yield strength, tensile strength and hardness reached 95.6 MPa, 162.2 MPa and HV53.3 respectively after 4 passes, and the comprehensive mechanical properties became better.

Key words： pure aluminum continuous extrusion texture evolution dynamic recrystallization mechanical property

Published: 25 June 2025 Online: 2025-06-19

CLC number:

TB31

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	GUO Tingbiao
	HOU Jiande
	FENG Rui
	YAO Zipeng
	ZHENG Shuangshuang
	ZHANG Guoqing

Cite this article:

GUO Tingbiao,HOU Jiande,FENG Rui, et al. Microstructure Evolution and Strengthening and Toughening Mechanism During Room-temperature C-ECAP of Pure Aluminum[J]. Materials Reports, 2025, 39(12): 24050232-6.

URL:

https://www.mater-rep.com/EN/10.11896/cldb.24050232 OR https://www.mater-rep.com/EN/Y2025/V39/I12/24050232

1 Wang H. Microstructure and mechanical properties of pure Al and Al-Mg alloys with high Mg content processed by high pressure torsion. Master’s Thesis, Jiangsu University, China, 2016 (in Chinese).
王辉. 高压扭转纯铝和高镁Al-Mg铝合金的微观结构与力学性能. 硕士学位论文, 江苏大学, 2016.
2 Li J, He T, Jia D S, et al. Forging & Stamping Technology, 2023, 48(11), 60 (in Chinese).
李健, 何涛, 贾东昇, 等. 锻压技术, 2023, 48(11), 60.
3 Bian Y N, Lu Y, Zhang J, et al. Acta Materialia, 2023, 253, 118964.
4 Li G S, Xu S K, Wan T J, et al. Materials Characterization, 2023, 205, 113248.
5 Mavlyutov A, Evstifeev A, Volosevich D, et al. Metals, 2023, 13(7), 1281.
6 Fu Y T, Sun J P, Yang Z Q, et al. Materials Characterization, 2020, 165, 110398.
7 Barr C J, Xia K. Journal of Materials Science & Technology, 2021, 82, 57.
8 Lowe T C, Davis S L, Campbell C R, et al. Materials Letters, 2021, 304, 130631.
9 Fu H W, Yin Y W, Yun X B, et al. Materials Design, 2022, 222, 111033.
10 Dvorak J, Sklenicka V, Horita Z. Materials Transactions, 2008, 49(1), 15.
11 Dong J F, Dong Q, Dai Y B, et al. Materials (Basel), 2017, 10(1), 87.
12 Tariku D, Kumar D S, Janaki P R, et al. International Journal of Mechanical and Materials Engineering, 2021, 16(1), 13.
13 Derakhshan F J, Parsa M, Jafarian H. Materials Science Engineering A, 2019, 747, 120.
14 Hou X Z, Ban C Y. Journal of Physics:Conference Series, 2021, 2021(1), 012077.
15 Rakhadilov К B, Kylyshkanov К M, Zhaparova S M. IOP Conference Series:Materials Science and Engineering, 2018, 447(1), 012084.
16 Xu S B, Wang H L, Liu P, et al. Journal of Wuhan University of Technology-Materials Science Edition, 2022, 37(1), 130.
17 Lei W W, Zhang H, Liang W. Journal of Materials Research and Technology, 2022, 17, 2587.
18 Su L H, Deng G Y, Luzin V, et al. Materials Science and Engineering A, 2020, 780, 139190.
19 Li H X, Gao S, Tomota Y, et al. Acta Materialia, 2021, 206, 116621.
20 Wang G W, Song D, Zhou Z K, et al. Coatings, 2020, 10(3), 216.