冷轧变形量对5A02铝合金管材组织和性能的影响

doi:10.11896/cldb.18050021

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (7140KB)
Export: BibTeX | EndNote (RIS)

Abstract At room temperature, two-pass cold rolling of hot extruded 5A02 aluminum alloy tubes were processed with four different process parameters(A—D). Billets with size of 65.5 mm×5.5 mm (outer diameter * wall thickness, same below) were cold rolled into tubes with size of 58 mm×2.5 mm, with a total reduction of 57.6%.The reduction (%)of first and second pass cold rolling was as following respectively:A(20.2%,47.3%), B(34.4%,35.9%), C(43.6%,25.4%), D(52.7%,11.1%). After each pass of rolling, the tubes were fully annealed at 410 ℃/1 h. To figure out effect of cold rolling reduction on microstructure and properties of 5A02 aluminum alloy tubes, themicrostructure, mechanical properties, and tensile fracture morphology of cold-rolled tubes were observed and analyzed by means of metallographic microscope, scanning electron microscope(“SEM”),energy spectrometer and electronic universal testing machine.The results are as below:for A—D, after the first cold rolling, grain size and second phase become smaller gradually, while tensile strength and breaking elongation become larger gradually; for D, after the second cold rolling, grain size is smallest within 15—55 μm, tensile strength is 186 MPa,and breaking elongation is 29%; for A—D, after the second cold rolling, second phase is the same in size and distribution. The above results show that:with the reduction of cold rolling becomes largergradually, grain size of the tubes become smaller and mechanical properties become better; under the circumstance that total rolling reduction keeps the same, after cold rolling with large reduction in single pass, the grain of the annealed tubes is smaller and more uniform, and its mechanical properties are better;the size of the second phase particles decreases with the increase of cold rolling reduction, and under the circumstance that total rolling reduction keeps the same,the size of the second phase keeps the same as well.

Key words： 5A02 aluminum alloy tubes cold rolling reduction microstructure

Published: 28 April 2019

CLC number:

TG339

Fund:This work was financially supported by the National Natural Science Foundation of China (51205028).

About author:: Chuan Wang, received his M.S. degree in June 2018 from General Research Institute for Nonferrous Metals. Mainly engaged in the research of aluminum alloy pipe rolling process.; Defu Li, received his Ph.D. degree in materials from Harbin Institute of Technology in March 1995, Deputy Director, National Nonferrous Metal Composites Engineering Technology Research Center, General Research Institute for Nonferrous Metals.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	WANG Chuan
	LI Defu

Cite this article:

WANG Chuan,LI Defu. Effect of Cold Rolling Reduction on Microstructure and Properties of 5A02 Aluminum Alloy Tubes[J]. Materials Reports, 2019, 33(8): 1361-1366.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.18050021 OR http://www.mater-rep.com/EN/Y2019/V33/I8/1361

1 Chu G, Liu W. JOM, 2013, 65(5),599.
2 Qin Liyan, Liu Liying, Zhao Hailong. Heilongjiang Metallurgy, 2007(3),1(in Chinese).
秦丽艳,刘丽英, 赵海龙.黑龙江冶金, 2007(3),1.
3 聂祚仁,林双平,黄晖,等. 中国专利,CN 101403080, 2009.
4 Wang X P, Chen Z J, Geng D Y, et al. Light Alloy Fabrication Techno-logy, 2010,38(7),35(in Chinese).
汪祥鹏,陈忠家,耿德远,等.轻合金加工技术,2010,38(7),35.
5 Zhang Qi,Zhao Pizhi,Zou Liying,et al. Chinese Journal of Rare Metals, 2016, 40(2),110(in Chinese).
张琪, 赵丕植, 邹立颖,等.稀有金属, 2016, 40(2),110.
6 Feng Shaogui, Lan Jian, Gu Qing. Forging & Stamping Technology, 2017, 42(6),82(in Chinese).
冯绍贵, 兰箭, 顾青.锻压技术, 2017, 42(6),82.
7 Hu Jie, Guo Qingmiao, Li Defu, et al. Forging & Stamping Technology, 2011, 36(1), 65(in Chinese).
胡捷, 郭青苗, 李德富,等.锻压技术, 2011, 36(1), 65.
8 Li Haitao, Guo Qingmiao, Hu Jie, et al. Forging & Stamping Technology, 2011, 36(6),103(in Chinese).
李海涛, 郭青苗, 胡捷,等.锻压技术, 2011, 36(6),103.
9 Cui X L, Wang X S, Yuan S J. International Journal of Mechanical Scie-nces, 2014, 88,232.
10 Li Ruifeng. Effect of rolling deformation on microstructure and properties of thick plates of Al-6.4Zn-2.3Mg-2.1 Cu alloy. Master’s Thesis, Northeastern University, China, 2013(in Chinese).
李瑞锋. 轧制变形对Al-6.4Zn-2.3Mg-2.1Cu合金厚板组织性能的影响. 硕士学位论文,东北大学, 2013.
11 Lin Gang, Lin Huiguo, Zhao Yutao. Application Manual of Aluminum Alloy, Mechanical Industry Press, China, 2006(in Chinese).
林钢,林慧国,赵玉涛.铝合金应用手册,机械工业出版社, 2006.
12 Deng Xiaomin. Light Alloy Processing Technology, 2001, 29(11), 31(in Chinese).
邓小民.轻合金加工技术, 2001, 29(11),31.
13 Yang Yin, Shen Jian, Yan Xiaodong, et al. Hot Processing Technology, 2010, 39(21),41(in Chinese).
杨银, 沈健, 闫晓东,等.热加工工艺, 2010, 39(21),41.
14 Gao Yifei, Liang Xinbang, Deng Xinglin. GB/T 228.1-2010 metallic materials-tensile testing-part 1:method of test at room temperature, China Standard Press, China, 2012(in Chinese).
高怡斐, 梁新帮, 邓星临. GB/T 228.1-2010《金属材料拉伸实验第1部分:室温试验方法》实施指南,中国标准出版社, 2012.
15 Lin B, Zhang W, Zhao Y, et al. Materials Characterization, 2015, 104,124.
16 Du Yong.Dynamic precipitation and structure characterization of secondary phases in 5052-bassed alloys. Master’s Thesis, Chongqing University, China, 2015(in Chinese).
杜勇. 5052基铝合金中第二相的动态析出和结构表征. 硕士学位论文,重庆大学, 2015.
17 Zhou Jun. Influence of rolling and annealing process on microstructure and properties of 5182 aluminum alloy for automobile sheets. Master’s Thesis, Jiangxi University of Technology, China,2016(in Chinese).
周军. 轧制及退火工艺对汽车板用5182铝合金组织与性能的影响. 硕士学位论文,江西理工大学, 2016.
18 Lai Lin,Zhang Kui,Li Xinggang,et al. Chinese Journal of Rare Metals, 2016(6),552(in Chinese).
赖林, 张奎, 李兴刚,等.稀有金属, 2016(6),552.