Please wait a minute...
材料导报  2026, Vol. 40 Issue (18): 26050086-8    https://doi.org/10.11896/cldb.26050086
  金属与金属基复合材料 |
终轧温度对新型Nb-V-Ti-N耐候钢多相组织及力学性能的影响
胡兵1,*, 罗文宾1, 王秋鸣2, 王青峰2
1 辽宁工业大学材料科学与工程学院,辽宁 锦州 121001
2 燕山大学亚稳材料全国重点实验室,河北 秦皇岛 066004
Effect of Final Rolling Temperature on Multi-phase Microstructure and Mechanical Properties of a Novel Nb-V-Ti-N Weathering Steel
HU Bing1,*, LUO Wenbin1, WANG Qiuming2, WANG Qingfeng2
1 School of Materials Science and Engineering, Liaoning University of Technology, Jinzhou 121001, Liaoning, China
2 State Key Laboratory of Metastable Materials Science and Technology, Yanshan University, Qinhuangdao 066004, Hebei, China
下载:  全 文 ( PDF ) ( 14329KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 本工作采用Gleeble热-力模拟试验机,系统研究了控轧控冷工艺中终轧温度(820~880 ℃)对新型Nb-V-Ti-N系耐候钢组织演变及力学性能的影响。研究表明,随着终轧温度降低,多边形铁素体占比显著下降,针状铁素体与粒状贝氏体比例增加,马氏体/奥氏体组元的面积分数及尺寸均减小,820 ℃时出现少量板条贝氏体铁素体;终轧温度降低引起的组织细化和位错亚结构变化使母材强度和低温韧性均提高,但多边形铁素体的减少降低了母材塑性,且其与马氏体/奥氏体组元的同步减少降低了应变硬化能力,导致抗拉强度随终轧温度降低的增幅小于屈服强度,屈强比升高。本工作建立了终轧温度-组织-力学性能的关系,可为通过控轧控冷工艺制备兼具强塑性、低温韧性和低屈强比的耐候钢提供理论支撑。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
胡兵
罗文宾
王秋鸣
王青峰
关键词:  Nb-V-Ti-N耐候钢  终轧温度  微观组织  强塑性  低温韧性  屈强比    
Abstract: In this work, a Gleeble thermomechanical simulation tester was used to systematically investigate the effect of final rolling temperature (820—880 ℃) on the microstructural evolution and mechanical properties of a novel Nb-V-Ti-N weathering steel under thermo-mechanical controlled processing. The results show that with decreasing final rolling temperature, the fraction of polygonal ferrite decreases remarkably, while the fractions of acicular ferrite and granular bainitic ferrite increase. Both the area fraction and size of martensite/austenite constituents are reduced, and a small amount of lath bainitic ferrite forms at 820 ℃. Microstructure refinement and variation in dislocation substructures induced by the reduced final rolling temperature improve both the strength and low-temperature toughness of the base metal. Nevertheless, the reduction in polygonal ferrite deteriorates the ductility of the base metal. Meanwhile, the synchronous decrease of polygonal ferrite and martensite/austenite constituents weakens the strain-hardening capacity. Consequently, the increment of tensile strength is lower than that of yield strength with decreasing final rolling temperature, leading to an increased yield ratio. In this study, the correlation among final rolling temperature, microstructure, and mechanical properties is established, which may provide theoretical support for fabricating weathering steel with balanced strength-ductility, excellent low-temperature toughness, and a low yield ratio via thermo-mechanical controlled processing.
Key words:  Nb-V-Ti-N weathering steel    final rolling temperature    microstructure    strength and plasticity    low-temperature toughness    yield ratio
发布日期:  2026-10-15
ZTFLH:  TG335.1  
基金资助: 辽宁省科技计划联合计划(2025-MSLH-326);亚稳材料全国重点实验室(燕山大学)开放课题(202610)
通讯作者:  胡兵,博士,讲师,硕士研究生导师,主要研究先进钢铁材料及配套焊材与焊接工艺研发、材料表面改性。clhubing@lnut.edu.cn   
引用本文:    
胡兵, 罗文宾, 王秋鸣, 王青峰. 终轧温度对新型Nb-V-Ti-N耐候钢多相组织及力学性能的影响[J]. 材料导报, 2026, 40(18): 26050086-8.
HU Bing, LUO Wenbin, WANG Qiuming, WANG Qingfeng. Effect of Final Rolling Temperature on Multi-phase Microstructure and Mechanical Properties of a Novel Nb-V-Ti-N Weathering Steel. Materials Reports, 2026, 40(18): 26050086-8.
链接本文:  
https://www.mater-rep.com/CN/10.11896/cldb.26050086  或          https://www.mater-rep.com/CN/Y2026/V40/I18/26050086
1 Wei Y F. Construction & Design for Engineering, 2026(4), 77 (in Chinese).
魏艳风.工程建设与设计, 2026(4), 77.
2 Chen Y L, Yang J, Zhang Y H, et al. Journal of Sustainable Metallurgy, 2025, 11, 517.
3 Liu C S, Li F K, Wang Y, et al. Iron & Steel, 2025, 60(10), 1 (in Chinese).
刘成松, 李富康, 王勇, 等.钢铁, 2025, 60(10), 1.
4 Zhang J, Xin W B, Luo G P, et al. Materials Characterization, 2020, 16, 110201.
5 Qi H. Study on the precipitation behavior and microstructure evolution of the second phase during the high-heat input welding of V-N series ship plate. Master's Thesis, University of Science and Technology Liaoning, China, 2020 (in Chinese).
戚桓. V-N系船板钢大线能量焊接过程中第二相析出行为及组织演变研究. 硕士学位论文, 辽宁科技大学, 2020.
6 Shi R J, Wang T F, Gao K W, et al. Steel Research International, 2022, 93, 100415.
7 Jiang J, Bao W, Peng Z Y, et al. Construction and Building Materials, 2019, 200, 664.
8 Zhang Z J, Zhu S C, Xu S P, et al. Wide and Heavy Plate, 2025, 31(5), 10 (in Chinese).
张占杰, 朱书成, 许少普, 等.宽厚板, 2025, 31(5), 10.
9 Kim D W, Yang J H, Kim Y G, et al. Materials Science and Enginee-ring: A, 2022, 843, 143151.
10 Huang J N, Jan G C, Wang Y H, et al. Foundry Equipment & Technology, 2025(6), 60 (in Chinese).
黄家能, 詹光曹, 王义惠, 等.铸造设备与工艺, 2025(6), 60.
11 Williamson G K, Smallman R E. Philosophical Magazine, 1956, 1, 34.
12 Shi G H, Zhao H L, Zhang S M, et al. Materials Science and Enginee-ring: A, 2020, 769, 138501.
13 Liu S. Welded Pipe and Tube, 2026, 49(2), 17 (in Chinese).
刘硕.焊管, 2026, 49(2), 17.
14 Yakubtsov I A, Poruks P, Boyd J D, et al. Materials Science and Engineering: A, 2008, 480, 109.
15 Kusakin P, Belyakov A, Molodov A D, et al. Materials Science and Engineering: A, 2017, 687, 82.
16 Zhao L Y, Wang Q M, Shi G H, et al. Journal of Materials Research and Technology, 2023, 23, 2504.
17 Pei G B, Hui X Y, Du J B, et al. Transactions of Materials and Heat Treatment, 2026, 47(4), 149 (in Chinese).
裴冠博, 惠晓莹, 杜江波, 等. 材料热处理学报, 2026, 47(4), 149.
18 Cao J C, Yong Q L, Liu Q Y, et al. Journal of Materials Science, 2007, 42, 10080.
19 Seok M Y, Choi I C, Moon J, et al. Scripta Materialia, 2014, 87, 49.
20 Geng H Y, Sun X Y, Chen Z H, et al. Journal of Materials Research and Technology, 2026, 42, 10177.
21 Ja S J, Duan L N, Liu Q Y. Transactions of Materials and Heat Treatment, 2016, 37(3), 82(in Chinese).
贾书君, 段琳娜, 刘清友.材料热处理学报, 2016, 37(3), 82.
22 Shenawy E, Reda R. Journal of Materials Research and Technology, 2019, 8, 2819.
23 Tu X Y, Shi X B, Yan W, et al. Materials Science and Engineering: A, 2022, 831, 142230
24 Yan Y T, Li Q, Gong Z H, et al. Journal of Iron and Steel Research, 2026, 38(2), 276 (in Chinese).
燕怡彤, 李权, 龚志华, 等.钢铁研究学报, 2026, 38(2), 276.
25 Zhou S B, Hu C Y, Hu F, et al. Materials Science and Engineering: A, 2022, 846, 143175.
26 Yang Y, Zhang Z, Zhang W X, et al. Structural steel for bridge, Stan-dards Press of China, China, 2025, pp. 15 (in Chinese).
杨颖, 张哲, 张维旭, 等. 桥梁用结构钢, 中国标准出版社, 2025, pp. 15.
27 Yi L X, Liu X G, Gao C, et al. Structural steel for railway bridge, China Railway Publishing House, China, 2020, pp. 11 (in Chinese).
易伦雄, 刘晓光, 高策,等. 铁路桥梁用结构钢, 中国铁道出版社, 2020, pp. 11.
[1] 李田, 严佑锐凌, 牛晶晶, 牛赢, 郭强, 周惦武, 张明军. 直线摆动对钢/铝激光搭接焊接头组织性能的影响[J]. 材料导报, 2026, 40(3): 24120236-7.
[2] 张丽娇, 祝弘滨, 曲华, 王振民. 电弧增材制造技术研究进展[J]. 材料导报, 2026, 40(2): 24120065-10.
[3] 罗远震, 吴子彬, 长海博文, 李一峰, 王东涛, 张海涛, 张波. Al-Mg-Si系铝合金材料吸能性能的研究进展[J]. 材料导报, 2026, 40(17): 25090048-11.
[4] 李冰, 姜珊, 王刚, 王复栋, 王岭, 张罡. Monel400-Q345R爆炸复合板组织与性能研究[J]. 材料导报, 2026, 40(14): 25010132-7.
[5] 王浩军, 胡生双, 孙有政, 曹善鹏, 尤启凡, 牛鹏亮, 何文斌, 张兵宪. 7050铝合金热变形行为和组织演变研究[J]. 材料导报, 2026, 40(14): 25050017-9.
[6] 杨煜锋, 谭凯硕, 杨珂, 毛凌波, 董勇. CoCrFeMnNi基高熵合金-金属间化合物叠层复合材料的微观组织演化及力学性能[J]. 材料导报, 2026, 40(13): 25050131-10.
[7] 浦娟, 景浩展, 孙毓博, 石晓辉, 龙飞, 施清清, 徐九劼, 许祥平. ZrO2含量对金刚石/低碳钢感应钎焊层组织及性能的影响[J]. 材料导报, 2026, 40(12): 25070085-8.
[8] 李振亮, 杨帆, 王昊, 王晓东. Nb微合金化低碳钢梯度降温热变形行为研究[J]. 材料导报, 2026, 40(11): 25030245-7.
[9] 王挺, 恽迪, 杜沛南, 伍晓勇. 快堆金属燃料的研究进展[J]. 材料导报, 2026, 40(10): 25040205-15.
[10] 柴榕, 郭锋, 康裕, 蔡会生, 苏娟. 偏磷酸盐电解液中添加Ce对镁合金阳极氧化膜的改性作用[J]. 材料导报, 2026, 40(10): 25020133-5.
[11] 窦贵山, 曹睿, 焦世舜, 杨飞, 朱宇霆, 张克静, 刘春桃. 焊后热处理温度对960 MPa级低碳贝氏体钢焊缝金属显微组织和力学性能的影响[J]. 材料导报, 2026, 40(10): 25030167-6.
[12] 邓传森, 肖红婷, 刘严, 赵晨旭, 林斌, 陈俊锋, 陈玉龙, 邹林池, 闵爱武, 方添文. 铝合金先进断续时效工艺的研究进展[J]. 材料导报, 2026, 40(10): 25040219-11.
[13] 耿永辉, 时来鑫, 张烽, 邓秀亲. 轧制速度对两道次连续热轧-剪切-弯曲变形及后续退火AZ61镁合金板材微观组织和性能的影响[J]. 材料导报, 2026, 40(10): 25040126-7.
[14] 谢树磊, 欧美琼, 侯坤磊, 王旻, 马颖澈. Mo、W对多晶铸造镍基高温合金组织及应用性能影响的研究进展[J]. 材料导报, 2026, 40(1): 24110085-11.
[15] 王柯涵, 刘涵, 宗骁, 梁永锋, 南海, 林均品, 丁贤飞. TiAl合金片层组织不连续粗化转变[J]. 材料导报, 2026, 40(1): 24120163-7.
[1] Yanzhen WANG, Mingming CHEN, Chengyang WANG. Preparation and Electrochemical Properties Characterization of High-rate SiO2/C Composite Materials[J]. Materials Reports, 2018, 32(3): 357 -361 .
[2] Yimeng XIA, Shuai WU, Feng TAN, Wei LI, Qingmao WEI, Chungang MIN, Xikun YANG. Effect of Anionic Groups of Cobalt Salt on the Electrocatalytic Activity of Co-N-C Catalysts[J]. Materials Reports, 2018, 32(3): 362 -367 .
[3] Qingshun GUAN,Jian LI,Ruyuan SONG,Zhaoyang XU,Weibing WU,Yi JING,Hongqi DAI,Guigan FANG. A Survey on Preparation and Application of Aerogels Based on Nanomaterials[J]. Materials Reports, 2018, 32(3): 384 -390 .
[4] Wen XI,Zheng CHEN,Shi HU. Research Progress of Deformation Induced Localized Solid-state Amorphization in Nanocrystalline Materials[J]. Materials Reports, 2018, 32(1): 116 -121 .
[5] Hao ZHANG,Yongde HUANG,Yue GUO,Qingsong LU. Technological and Process Advances in Robotic Friction Stir Welding[J]. Materials Reports, 2018, 32(1): 128 -134 .
[6] Fengsen MA,Yan YU,Jie ZHANG,Haibo CHEN. A State-of-the-art Review of Cytotoxicity Evaluation of Biomaterials[J]. Materials Reports, 2018, 32(1): 76 -85 .
[7] Hong ZHANG,Ping ZHOU,Lan SUN,Hongyuan FAN. Effect of Solution Temperature on Microstructure and Properties of TP347HFG Heat Resistant Steel[J]. Materials Reports, 2018, 32(2): 234 -237 .
[8] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[9] Acidifier at High Temperature SiO2Bearing, , , , . Research on Stabilization of Free CaO in Basic Oxygen Furnace Slag with[J]. Materials Reports, 2018, 32(2): 301 -306 .
[10] Yankun DOU,Xinfu HE,Lixia JIA,Dongjie WANG,Shi WU,Wen YANG. The Contribution of Cu Precipitates to Hardening in α-Fe Matrix[J]. Materials Reports, 2018, 32(2): 307 -312 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed