TC4钛合金二维超声振动车削性能研究

doi:10.11896/cldb.22040390

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (40766KB)
Export: BibTeX | EndNote (RIS)

Abstract Due tothe superior physical and chemical properties, titanium alloys are widely used in various high-precision fields such as aerospace, ships, and weapon preparation. However, how to overcome its high specific heat capacity and low thermal conductivity to achieve high-quality and efficient processing has also become a hot issue in the field of machining. The two-dimensional ultrasonic vibration turning process has the cha-racteristics of intermittent turning, which can significantly improve the turning effect of difficult-to-machine materials such as composite materials, brittle materials and ceramic materials. Therefore, the two-dimensional ultrasonic vibration turning process was used to turn the TC4 titanium alloy, and compared with the traditional turning in terms of different processing properties. The experimental results demonstrated that the two-dimensional ultrasonic vibration turning process can effectively improve the machining quality of the workpiece, reduce the turning force during the cutting process, reduce the friction coefficient between the chip contact sliding area and the adhesive area, improve the tool life and have good chip breaking ability. In addition, ultrasonic vibration turning will increase the degree of work hardening of the workpiece surface, refine the surface grains, and increase the residual stress on the workpiece surface.

Key words： TC4 titanium alloy two-dimensional ultrasonic vibration turning surface quality tool wear cutting performance residual stress

Published: 25 November 2023 Online: 2023-11-21

CLC number:	TH161
	TH117

Fund:Basic and Applied Basic Research Foundation of Guangdong Province (2021A1515012394),Guangdong Province Key Area R&D Program,Guangdong Science and Technology Department (2020B090926003),and Zhuhai Industry Education and Research Cooperation Project (ZH22017001200011PWC).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	QU Shengguan
	ZHAI Jianshuo
	DUAN Chenfeng
	SUN Pengfei
	LI Xiaoqiang

Cite this article:

QU Shengguan,ZHAI Jianshuo,DUAN Chenfeng, et al. Research on Machinability of Two-dimensional Ultrasonic Vibration Assisted Turning of TC4 Titanium Alloy[J]. Materials Reports, 2023, 37(22): 22040390-9.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.22040390 OR http://www.mater-rep.com/EN/Y2023/V37/I22/22040390

1 Deng J X, Li Y S, Song W L. Wear, 2008, 265, 1776.
2 Ruggiero A, D Amato R, Gómez E, et al. Tribology International, 2016, 96, 349.
3 Ruggiero A, D-Amato R, Gómez E. Tribology International, 2015, 92, 154.
4 Bai D S, Sun J F, Chen W Y, et al. International Journal of Advanced Manufacturing Technology, 2016, 90, 2863.
5 Sharma A, Sharma M D, Sehgal R. Arabian Journal for Science and Engineering, 2012, 38, 3201.
6 Teimouri R, Amini S, Bami A B. Measurement, 2018, 116, 129.
7 Troitskii O A, Likhtman V I. Nauk, 1963, 148, 332.
8 Zhang X Y, Lu Z H, Peng Z L, et al. Chinese Journal of Mechanical Engineering, 2021, 57(05), 133 (in Chinese).
张翔宇, 路正惠, 彭振龙, 等. 机械工程学报, 2021, 57(05), 133.
9 Fang S X, Zhao H L, Zhang Q J. Chinese Journal of Mechanical Engineering, 2017, 53(19), 22 (in Chinese).
房善想, 赵慧玲, 张勤俭. 机械工程学报, 2017, 53(19), 22.
10 Xu W X, Zhang L C. Advances in Manufacturing, 2015, 3, 173.
11 Ni C B, Zhu L D, Yang Z C. Wear, 2019, 436, 203006.
12 Zhao B, Bie W, WanG X, et al. Ultrasonics, 2019, 98, 7.
13 Lv D S, Xu J H, Ding W F, et al. Journal of Materials Processing Technology, 2016, 229, 641.
14 Ma K, Zhu X J, Cui X L. Precision Engineering, 2020, 63, 148.
15 Ni C B, Zhu L D, Ning P S, et al. Chinese Journal of Mechanical Engineering, 2019, 55(7), 207 (in Chinese).
倪陈兵, 朱立达, 宁晋生, 等. 机械工程学报, 2019, 55(7), 207.
16 Mohammad L, Saeid A, Javad A. Tribology International, 2020, 151, 106492.
17 Zhang C, Guo P, Ehmann K F, et al. Ultrasonics, 2016, 67, 30.
18 Zhang J G, Norikazu S, Wang Y L, et al. Journal of Materials Processing Technology, 2014, 214(11), 2644.
19 Zhang C, Guo P, Ehmann K F, et al. Materials and Manufacturing Processes, 2015, 30(8), 1001.
20 Ma C X, Shamoto E, Moriwaki T, et al. International Journal of Machine Tools and Manufacture, 2005, 45(11), 1295.
21 Lin J Q, Han J G, Zhou X Q. International Journal of Mechanical Sciences, 2016, 117, 43.
22 Gi D K, Byoung G L. Materials Processing Technology, 2007, 151, 221.
23 Li W H, Pi Y Y. Chinese Tool Engineering, 2022, 56(6), 83 (in Chinese).
李会文, 皮云云. 工具技术, 2022, 56(6), 83.
24 Pang Y, Ma Y, Xu C. Chinese Diamond and Abrasives Engineering, 2019, 39(2), 83 (in Chinese).
庞宇, 马原, 许超. 金刚石与磨料磨具工程, 2019, 39(2), 83.
25 Li Y, Zhang M L, Dong H T, et al. Chinese Light Industry Machinery, 2020, 38(5), 24 (in Chinese).
李莹, 张敏良, 董慧婷, 等. 轻工机械, 2020, 38(5), 24.
26 Bai W. Experimental study on vibration-assisted cutting mechanism and machinability of typical difficult-to-machine materials. Ph. D. Thesis, Huazhong University of Science and Technology, China, 2018 (in Chinese).
柏伟. 典型难加工材料振动辅助切削机理与可加工性实验研究. 博士学位论文, 华中科技大学, 2018.
27 Nath C, Rahman M, Neo K S. Journal of Materials Processing Technology, 2009, 209, 4459.
28 Saito H, Jung H J, Shamoto E. Precision Engineering, 2016, 45, 44.
29 Hu Z T, Qin N, Liu F. Mechanical Design and Manufacturing, 2018(2), 164 (in Chinese).
胡智特, 秦娜, 刘凡. 机械设计与制造, 2018(2), 164.
30 Sun F J. Research on cutting mechanism of Ti-6Al-4V HIP powder metallurgy materials. Ph. D. Thesis, South China University of Technology, China, 2015 (in Chinese).
孙富建. Ti-6Al-4V HIP粉末冶金材料切削机理研究. 博士学位论文, 华南理工大学, 2015.
31 Da-Silva R B, Vieira J M, Cardoso R N, et al. Wear, 2011, 271(9-10), 2459.
32 Mohammad L, Saeid A, Sayed A S. International Journal of Mechanical Sciences, 2019, 160, 241.
33 Mohammad L, Saeid A, Javad A. Tribology International, 2020, 151, 106492.
34 Liu X. Experimental study on physical and mechanical properties of ultrasonic-assisted hard turning of GCr15 bearing steel. Ph. D. Thesis, Henan University of Technology, China, 2011 (in Chinese).
刘向. 超声辅助硬态车削GCr15轴承钢物理机械性能的试验研究. 博士学位论文, 河南理工大学, 2011.
35 Shang Z H, ZUO X Z. Chinese Tool Engineering, 2005(2), 16 (in Chinese).
尚自河, 左秀芝. 工具技术, 2005(2), 16.