不同补焊次数下ZG06Cr13Ni4Mo的组织演变规律

doi:10.11896/cldb.22020127

Abstract
Figure/Table
References
Related Citation (3)

Download:

Full Text ( PDF ) (21587KB)
Export: BibTeX | EndNote (RIS)

Abstract In order to clarify the evolution law of microstructure in the repair welding area of ZG06Gr13Ni4Mo martensitic stainless steel under different repair times, GTAW was used to repair 40 mm ZG06Gr13Ni4Mo once and twice, temper at 600 ℃ for 2 hours after each repairing. OM, SEM, EBSD and TEM were used to detect the microstructure changes of the base metal and the repair area under different repair times, and the microstructure evolution law of the repair area was studied. The results show that the phase of the repaired area is mainly composed of martensite and a small amount of reversed austenite, which is distributed in the boundary of martensite and matrix in the form of thin laths. The content of reversed austenite in the repair welding areas increases with the increase of repair welding times, and the content of reversed austenite in the weld zone is greater than that in heat affected zone. In addition, the grain size in the repaired joint tends to refinement. Compared with the base metal, the grain size in the once and twice weld zone is refined by 45.2% and 61.9%, while the grain size in the weld zone is refined by 40.8% and 48.3% respectively compared with that in the heat affected zone, and the size of reversed austenite is about 50% of that of martensite. The orientation of texture changes from 〈101〉 to anisotropy, the small angle grain boundary decreases and the large angle grain boundary increases.With the increase in the number of repairing welds, the hardness and strength of the repaired joints decrease gradually, and the yield strength and plasticity increase gradually.

Key words： repair welding ultra low carbon martensitic stainless steel reversed austenite electron back-scattered diffraction

Published: 25 August 2023 Online: 2023-08-14

CLC number:

TG455

Fund:Key Projects for Serving Local Areas in Liaoning Province (LFGD2019001).

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	SU Yunhai
	WEI Zuyong
	ZHANG Guiqing
	ZHANG Xiangwen

Cite this article:

SU Yunhai,WEI Zuyong,ZHANG Guiqing, et al. Microstructure Evolution Law of ZG06Cr13Ni4Mo with Different Repair Welding Numbers[J]. Materials Reports, 2023, 37(16): 22020127-6.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.22020127 OR http://www.mater-rep.com/EN/Y2023/V37/I16/22020127

1 Koistinen D P, Marburger R E. Acta Metallurgica, 1959, 7(1),59.
2 Gao Z, Wang C, Liu Y. International Journal of Electrochemical Science, 2015, 10(8),6487.
3 Yin Y, Kang P, Zhang R H, et al. China Welding, 2020, 30(1), 21.
4 Hang T Y, Wang Z M, Yang G H,et al.Electromechanical Technology of Hydropower Station, 2021, 44(1),50(in Chinese).
韩天宇, 王智民, 杨光辉, 等. 水电站机电技术, 2021, 44(1), 50.
5 Thibault D, Bocher P, Thomas M, et al. Materials Science & Engineering A, 2010, 527(23), 6205.
6 Hassan A J, Boukharouba T, Miroud D, et al. China Welding, 2021, 29(4), 7.
7 Kang M, Jiang M, Sridar S, et al. Journal of Materials Engineering and Performance, 2022, 31,254.
8 Ahmad Z, Shahid M, Abbas M. Journal of the Brazilian Society of Mechanical Sciences and Engineering, 2017, 39(4), 1233.
9 Su Y H, Wei Z Y, Li G, et al. Coatings, 2022,12(1), 1.
10 Zhang G Q, Tong X, Wu G H, et al. Materials Science and Engineering: A, 2021, 821, 141577.
11 Mirakhorli F, Cao X, Pham X T, et al. Materials Characterization, 2017, 123, 264.
12 Sanctis M D, Lovicu G, Valentini R, et al. Metallurgical & Materials Transactions A, 2015, 46(5),1878.
13 Wang P, Lu S P, Li D Z, et al. Acta Metallurgica Sinica, 2008, 44(6), 681.
14 Thibault D, Bocher P, Thomas M. Journal of Materials Processing Technology, 2009, 209(4), 2195.
15 Amrei M M, Monajati H, Thibault D, et al. Materials Characterization, 2016, 111, 128.
16 Liu Z C, Li Y M, Feng T C, et al. Microstructure identification of alloy stell. Beijing: Higher Education Press, China, 2017, pp. 143 (in Chinese).
刘宗昌,李一鸣,冯佃臣, 等.合金钢显微组织辨识. 高等教育出版社, 2017,pp. 143.
17 Zhang M, Wu W G, Chu Q L, et al. Transactions of the China Welding Institution, 2013, 34(8),4(in Chinese).
张敏, 吴伟刚, 褚巧玲,等.焊接学报, 2013, 34(8),4.
18 Liu L, Yang Z G, Zhang C. Journal of Alloys & Compounds, 2013, 577, 654.
19 Zhang Y, Zhang C, Yuan X, et al. Materials, 2019, 12(4),589.
20 Bilmes P D, Solari M, Llorente C L. Materials Characterization, 2001, 46(4),285.
21 Chen S, Hu F, Wang Y C, et al. Journal of Material Heat Treatment, 2020, 41(12),80 (in Chinese).
程石, 胡锋, 王亚超,等.材料热处理学报, 2020, 41(12), 80.
22 Li Z D, Cui Z D, Wang W Z, et al.Transactions of the China Welding Institution, 2019, 40(8), 89 (in Chinese).
李兆登, 崔振东, 王维珍,等. 焊接学报, 2019, 40(8), 89.