METALS AND METAL MATRIX COMPOSITES |
|
|
|
|
|
Research Status of Magnesium-Lithium Alloy Welding Technology |
LIU Qinyu1,2, ZHOU Li1,2,*, RONG Xiaoyu3, YANG Haifeng1,2, ZHAO Hongyun1,2
|
1 State Key Laboratory of Advanced Welding and Joining, Harbin Institute of Technology, Harbin 150001, China 2 Shandong Provincial Key Laboratory of Special Welding Technology, Harbin Institute of Technology at Weihai, Weihai 264209, Shandong, China 3 JianRui New Material Technology Co., Ltd at Ningbo, Ningbo 315400, Zhejiang, China |
|
|
Abstract Magnesium-lithium alloy (Mg-Li alloy) is a type of rising ultra-light material with a series of advantages, such as high specific strength and specific stiffness, high Young's modulus, excellent plasticity and impact toughness, which is one of the ideal structural materials in aerospace and aviation, weapon, nuclear, vehicle, medical equipment and other fields. With the rapid development and application of Mg-Li alloy, new requirements for the joining of Mg-Li alloy arise. Appropriate welding methods need to be developed to achieve the join and replace the mechanical joint such as riveting gradually. Currently, the welding methods of Mg-Li alloy mainly focus on tungsten inert gas arc welding (TIG wel-ding), laser welding, electron beam welding and friction stir welding. The core problem of fusion welding is the control of heat input. Improper control will lead to welding defects,such as grain coarsening, element loss and incomplete penetration, etc. Although friction stir welding can avoid these defects to a large extent, deteriation in joint elongation is difficult to avoid. At present, the research mainly focus on weld process, microstructure and mechanical properties of joints, and the welding of Mg-Li alloy is successfully realized through the exploratory research. Currently, many remarkable achievements about study of Mg-Li alloy welding process have been achieved, and well-formed and defect-free joints can be obtained under a wide process window. Under the appropriate welding process, the grain in the weld zone was significantly refined, and nanoscale grains even appeared. In some studies, the microstructure distribution of the welded joint was uniform, and extremely narrow heat affected zone was successfully obtained. Most studies have shown that the tensile strength of joints and the hardness of welds are improved, and artificial aging treatment to restore the elongation of joints has a good prospect. In order to further popularize the practical application of Mg-Li alloy welding technology, the joint formation, microstructure and mechanical pro-perties obtained by the above welding methods were reviewed in this paper. The core problems and probable solutions of different welding me-thods in Mg-Li alloy welding were analyzed and discussed. The exploration direction of Mg-Li alloy welding technology in the future was considered and prospected.
|
Published:
Online: 2022-05-24
|
|
Fund:General Project of National Natural Science Foundation of China (51974100) and the Key Research and Development Project of Shandong Province (2018GGX103053). |
|
|
1 Kojima Y, Inoue M, Tanno O. Journal of the Japan Institute of Metals, 1990, 54(3), 354. 2 Zhang M L, Elkin F M. Super light magnesium-lithium alloy, Science Press, China, 2010,pp. 5 (in Chinese). 张密林, Elkin F M. 镁锂超轻合金, 科学出版社, 2010, pp.5. 3 Haferkamp H, Niemeyer M, Boehm R, et al. Materials Science Forum, 2000, 350(3), 31. 4 Yang G Y, Hao Q T, Jie W Q. Foundry Technology, 2004, 6(1), 19 (in Chinese). 杨光昱, 郝启堂, 介万奇. 铸造技术, 2004, 6(1), 19. 5 Muga C O, Zhang, Z W. Advances in Materials Science and Engineering, 2016, 2016, 11. 6 Wu L B, Cui C L, Wu R Z, et al. Materials Science and Engineering A, 2011, 528, 2174. 7 Liu X H. Study on preparation and properties of superlight-superplastic Mg-Li alloy. Ph.D. Thesis, Harbin Engineering University, China, 2012(in Chinese). 刘旭贺. 超轻超塑性镁锂合金的制备及性能研究. 博士学位论文, 哈尔滨工程大学, 2012. 8 Zou Y. Effects of alloying elements and processing on deformation mechanisms and properties of Mg-Li alloys. Ph.D. Thesis, Harbin Engineering University, China, 2016(in Chinese). 邹云. 镁锂合金成分和处理工艺对变形机制及性能的影响. 博士学位论文, 哈尔滨工程大学, 2016. 9 Zhang J, Zhang Z H. Magnesium alloys and their applications, Chemical Industry Press, China, 2004, pp. 283(in Chinese). 张津, 章宗和. 镁合金及应用, 化学工业出版社, 2004, pp. 283. 10 Zhao H L, Guan S K, Zheng F Y. Transactions of Nonferrous Metals So-ciety of China, 2005, 15(1), 144. 11 Wu W, Qiao H, An K, et al. International Journal of Plasticity, 2014, 62, 105. 12 Liu Y, Liu X H, Xiao Y, et al. Light Alloy Fabrication Technology, 2017, 45(1), 61 (in Chinese). 刘洋, 刘旭贺, 肖阳, 等. 轻合金加工技术, 2017, 45(1), 61. 13 Cao F R, Ding H, Li Y L,et al. Materials Science and Engineering A, 2010, 527(9), 2335. 14 Atkins G, Marya M, Olson D, et al. In: Symposium on Magnesium Technology 2004 Held at the TMS Annual Meeting. Charlotte, 2004, pp. 37. 15 Yu W X. Study on laser welding technology of LZ91 Mg-Li alloy. Master's Thesis, Huazhong University of Science and Technology, China, 2018 (in Chinese). 余文祥. LZ91镁锂合金激光焊接工艺研究. 硕士学位论文, 华中科技大学, 2018. 16 Ning J, Zhang L G, Han C Q, et al. Materials Research Express, 2019, 6(10), 106545. 17 Jiang B C, Hu S H. Ordnance Material Science and Engineering, 2019, 42(6), 50 (in Chinese). 姜炳春, 胡少华. 兵器材料科学与工程, 2019, 42(6), 50. 18 Song K J, Dong Z B, Li Y, et al. Electro-Mechanical Engineering, 2020, 36(1), 46 (in Chinese). 宋奎晶, 董志波, 李洋, 等. 电子机械工程, 2020, 36(1), 46. 19 Shah P H, Badheka V J. Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications, 2019, 233(6), 1191. 20 Defalco J. Welding Journal, 2006, 85(3), 42. 21 Arbegast W J. Welding Journal, 2006, 85(3), 28. 22 Gürel Ćam, Selcuk Mistikoglu. Journal of Materials Engineering and Performance, 2014, 23(6), 1936. 23 Che Q Y, Wang K S, Wang W, et al. Rare Metals, 2019, 40(9), 2552. 24 Yang C W. Materials science, Intechopen, Rijeka, 2013, pp. 303. 25 Jackson J H, Frost P D, Loonam A C, et al. JOM, 1949, 185, 149. 26 Freeth W E, Raynor G V. Journal Institute of Metals, 1953, 82, 575. 27 Mathewson A G, Myers H P. Journal of Physics F: Metal Physics, 1973, 3, 623. 28 Saboo M, Atkinson J T N. Journal of Materials Science, 1982, 17, 3564. 29 Crisp R S. Journal of Physics F: Metal Physics, 1983, 13, 1317. 30 Sambasiva R G, Prasad Y V R K. Research Mechanica, 1983, 9, 41. 31 Yang C W, Lui T S, Chen L H, et al. Scripta Materialia, 2009, 61(12), 1141. 32 Liu X H, Gu S H, Wu R Z, et al. Transactions of Nonferrous Metals So-ciety of China, 2011, 21(3), 477. 33 Lyu J X, Yang W X, Wu S K, et al. Chinese Journal of Lasers, 2014, 41(3), 60 (in Chinese). 吕俊霞, 杨武雄, 吴世凯, 等. 中国激光, 2014, 41(3), 60. 34 Zhang J, Feng X S, Zhang C C, et al. Transactions of the China Welding Institution, 2017, 38(4), 119(in Chinese). 张婧, 封小松, 张成聪, 等. 焊接学报, 2017, 38(4), 119. 35 Askariani S A, Pishbin H, Moshref J M. Journal of Alloys and Compounds, 2017, 724, 859. 36 Liu G. Investigation of microstructure and properties of dual phase Mg-Li alloy by friction stir processing and welding. Ph.D. Thesis, Chongqing University, China, 2018 (in Chinese). 刘刚. 双相镁锂合金搅拌摩擦加工和焊接的组织与性能研究. 博士学位论文, 重庆大学, 2018. 37 Cao F R, Xue G Q, Zhou B J, et al. Metals and Materials International, 2019, 25, 570. 38 Liu G, Ma Z D, Wei G B, et al. Journal of Materials Processing Techno-logy, 2018, 267, 393. 39 Yang C W, Chen Y W. Procedia Engineering, 2014, 75, 88. 40 Fan M, Zhang G F, Chai D L, et al. Welding Pipe and Tube, 2019, 42(11), 25 (in Chinese). 范蒙, 张贵锋, 柴东郎, 等. 焊管, 2019, 42(11), 25. 41 Chen H C, Hung F Y, Lui T S, et al. Materials Transactions, 2013, 54(4), 505. 42 Yang C W. Materials Transactions, 2014, 55(2), 371. 43 Liu F C, Tan M J, Liao J, et al. Journal of Materials Science, 2013, 48(24), 8539. |
|
|
|