变形镁合金轧制成形研究进展

doi:10.11896/cldb.19090002

Abstract
Figure/Table
References
Related Citation (15)

Download:

Full Text ( PDF ) (15689KB)
Export: BibTeX | EndNote (RIS)

Abstract ith the acceleration of industrialization, materials with high comprehensive performance are increasingly favored by domestic and foreign researchers. Magnesium alloy is the lightest structural material and has the advantages of high specific strength and stiffness, it has attracted more and more attention in the fields of vehicle, aerospace and other fields. When the traditional casting and die casting processes are used to produce magnesium alloy, its comprehensive properties are limited due to the common defects in the casting process, which often fail to meet the requirements of industrial production. Continuous production of magnesium alloy plates can be achieved through rolling and the comprehensive properties of magnesium alloy plates can be improved. However, as magnesium alloy is a special crystal structure material with hexagonal close pack, the independent slip system is less than other crystal structure materials with body centered cubic and face centered cubic, which leads to the poor formability of magnesium alloy plates in the rolling deformation process and after rolling,which is mainly reflected in: (1) edge crack is easy to occur in the rolling process; (2) after rolling, the elongation and strength properties of the plates are not significantly improved; (3) after rolling, it is not easy to obtain the plates with excellent combination of high strength and high plastic properties. At present, domestic and foreign researchers mainly improve the formability of magnesium alloy plates by three kinds of nine rolling processes: (1) high speed rolling, on-line heating rolling, vertical rolling, cross rolling-suppress edge cracking; (2) differential speed rolling, cross-roll rolling, equal channel angular rolling-additional shear force for rolling weakens the basal texture; (3) accumulative roll bonding, hard-plate rolling-fine grain, improve strength and obtain high plasticity. The paper mainly from the magnesium alloy plates edge crack suppression, weakening basal texture, grain refinement as a starting point, in order to improve the formability of magnesium alloy as the research direction, the effects of the above nine rolling processes on microstructure, texture evolution and deformation mechanism of magnesium alloy plates and the defect of magnesium alloy plates were optimized and the formability was improved. Meanwhile, the research direction of the future rolling deformation of magnesium alloy is prospected, which provides a reference for obtaining the magnesium alloy plate with no edge crack, high strength and high plastic alloy plates.

Key words： magnesium alloy rolling process edge cracks texture formability

Published: 17 November 2020

CLC number:

TG335

Fund:This work was financially supported by the Joint Funds of the National Natural Science Foundation of China (U1610253), the Key Research and Development Program of Shanxi Province (201603D111004), Sponsored by the Fund for Shanxi “1331 Project” Key Subjects Construction, Shanxi Province Patent Promotion and Implementation Funding Special Project.

About author:: Leijie Zhao, male, born in October 1995, majored in mechanical engineering at Taiyuan University of Science and Technology. His research direction is magnesium alloy plates rolling.
Lifeng Ma, male, born in August 1977, he graduated from Taiyuan University of Technology. Dean, professor, doctoral supervisor of School of Mechanical Engineering, Taiyuan University of Science and Technology, majoring in research in the field of modern design met-hods for metallurgical processes and large-scale metallurgical equipment. He has hosted and completed three National Natural Science Foundation Key Projects of China and General and Youth Projects, and has been awarded “Leading Talents of Entrepreneurship and Innovation”, “High-Level Innovation and Entrepreneurship Talents” and “333 Talents” in Jiangsu Province, et al. Currently, more than 40 papers have been published (SCI/EI included 20 papers) and 12 invention patents have been anthorized.

	Service
	E-mail this article
	Add to my bookshelf
	Add to citation manager
	E-mail Alert
	RSS
	Articles by authors
	ZHAO Leijie
	MA Lifeng
	HAN Tingzhuang
	FAN Qinhong

Cite this article:

ZHAO Leijie,MA Lifeng,HAN Tingzhuang, et al. Research Progress of Wrought Magnesium Alloy Rolling Forming[J]. Materials Reports, 2020, 34(21): 21135-21145.

URL:

http://www.mater-rep.com/EN/10.11896/cldb.19090002 OR http://www.mater-rep.com/EN/Y2020/V34/I21/21135

[1]	Joost W J. JOM, 2012, 64(9), 1032.
[2]	Patel H A, Chen D L, Bhole S D, et al. Materials Science and Enginee-ring A, 2010, 528(1), 208.
[3]	Tahreen N, Chen D L, Nouri M, et al. Materials Science & Engineering: A, 2014, 594, 235.
[4]	Liu D, Liu Z Y, Wang E. Materials Science and Engineering: A, 2014, 612, 208.
[5]	Zhang H, Yan Y, Fan J F, et al. Materials Science and Engineering: A, 2014, 618, 540.
[6]	Chen W Z, Zhang W C, Qiao Y D, et al. Journal of Alloys and Compounds, 2016, 665, 13.
[7]	Agnew S R, Duygulu O. International Journal of Plasticity, 2005, 21(6), 1161.
[8]	Yu H H, Xin Y C, Chapuis A, et al. Scientific Reports, 2016, 6, 29283.
[9]	Li M M, Wu B L, Zhang L, et al. Hot Working Technology, 2017, 46(3), 38(in Chinese).
	李苗苗, 武保林, 张利, 等. 热加工工艺, 2017, 46(3), 38.
[10]	Liu H Q, Tang D, Hu S P, et al. The Chinese Journal of Nonferrous Metals, 2012, 22(12), 3293(in Chinese).
	刘华强, 唐荻, 胡水平, 等. 中国有色金属学报, 2012, 22(12), 3293.
[11]	Liu D, Liu Z Y, Wang E. Materials Science & Engineering A, 2014, 612, 208.
[12]	Huang X S, Suzuki K, Chino Y, et al. Journal of Alloys and Compounds, 2015, 632, 94.
[13]	Amjad J, Frank C. Journal of Magnesium and Alloys, 2019, 7, 27.
[14]	Rao X X, Wu Y P, Pei X B, et al. Materials Science & Engineering A, 2019, 754, 112.
[15]	Jia W T, Ma L F, Ma Z Y, et al. Rare Metal Materials and Engineering, 2016, 45(1), 152(in Chinese).
	贾伟涛, 马立峰, 马自勇, 等. 稀有金属材料与工程, 2016, 45(1), 152.
[16]	Zhang D F, Dai Q W, Fang L, et al. Transactions of Nonferrous Metals Society of China, 2011, 21(5), 1112.
[17]	Ma L F, Pang Z N, Huang Q X, et al. Rare Metal Materials and Engineering, 2014, 43(S1), 387(in Chinese).
	马立峰, 庞志宁, 黄庆学, 等. 稀有金属材料与工程, 2014, 43(S1), 387.
[18]	Sanjari M, Kabir A S H, Farzadfar A, et al. Journal of Materials Science, 2014, 49(3), 1426.
[19]	Manabe S, Utsunomiya H, Sakai T, et al. Advanced Materials Research, 2014, 922, 469.
[20]	Young J P, Ayoub G, Mansoor B, et al. Journal of Materials Processing Technology, 2015, 216, 315.
[21]	Guo F, Zhang D F, Yang X S, et al. Materials Science & Engineering A, 2014, 607, 383.
[22]	Su J, Sanjari M, Kabir A S H, et al. Materials Science & Engineering A, 2015, 636, 582.
[23]	Pan F S, Zeng B, Jiang B, et al. Journal of Alloys and Compounds, 2017, 693, 414.
[24]	Liu Q, Song J F, Pan F S, et al. Metals, 2018, 8(10), 860.
[25]	Ding Y P, Le Q C, Zhang Z Q, et al. Journal of Materials Processing Technology, 2013, 213(12), 2101.
[26]	Huang Z Q, Huang Q X, Wei J C, et al. Journal of Materials Processing Technology, 2017, 246, 85.
[27]	Wei J C, Huang Q X, Huang Z Q, et al. Rare Metal Materials and Engineering, 2018, 47(2), 652(in Chinese).
	韦建春, 黄庆学, 黄志权, 等. 稀有金属材料与工程, 2018, 47(2), 652.
[28]	Jia W T, Le Q C, Tang Y, et al. Journal of Materials Science & Technology, 2018, 34(11), 2069.
[29]	Zhi C C, Ma L F, Huang Q X, et al. Journal of Materials Processing Technology, 2018, 255, 333.
[30]	Shim M S, Suh B C, Kim J H, et al. Metals and Materials International, 2015, 21(3), 490.
[31]	Chino Y, Sassa K, Kamiya A, et al. Materials Letters, 2007, 61(7), 1504.
[32]	Cheng Y Q, Chen Z H, Xia W J. Materials Characterization, 2007, 58(7), 617.
[33]	Cho J H, Kim H W, Kang S B, et al. Acta Materialia, 2011, 59(14), 5638.
[34]	Luo D, Wang H Y, Zhao L G, et al. Materials Characterization, 2017, 124, 223.
[35]	Kim W Y, Kim W J. Materials Science & Engineering A, 2014, 594, 189.
[36]	Kwak T Y, Kim W J. Journal of Materials Science & Technology, 2017, 33(9), 919.
[37]	Ko Y G, Hamad K. Journal of Alloys and Compounds, 2018, 744, 96.
[38]	Hamad K, Ko Y G. Scientific Reports, 2016, 6, 29954.
[39]	Yang H W, Widiantara I P, Ko Y G. Materials Letters, 2018, 213, 54.
[40]	Kim D G, Lee K M, Lee J S, et al. Materials Letters, 2012, 75, 122.
[41]	Lim H K, Lee J Y, Kim D H, et al. Materials Science and Engineering A, 2009, 506(1-2), 63.
[42]	Chino Y, Sassa K, Kamiya A, et al. Materials Science & Engineering A, 2008, 473(1-2), 195.
[43]	Cheng Y Q, Chen Z H, Xia W J, et al. Journal of Plasticity Engineering, 2007, 14(4), 127(in Chinese).
	程永奇, 陈振华, 夏伟军, 等. 塑性工程学报, 2007, 14(4), 127.
[44]	Cheng Y Q, Chen Z H, Xia W J. Materials Characterization, 2007, 58(7), 617.
[45]	Hassani F Z, Ketabchi M, Hassani M T. Journal of Materials Science, 2011, 46(24), 7689.
[46]	Tu J, Zhou T, Liu L, et al. Journal of Alloys and Compounds, 2018, 768, 598.
[47]	Song D H, Zhou T, Tu J, et al. Journal of Materials Processing Technology, 2018, 259, 380.
[48]	Yuan Y C, Ma A B, Gou X F, et al. Materials Science & Engineering A, 2015, 630, 45.
[49]	Zhang L, Wang Q D, Liao W J, et al. Materials Characterization, 2017, 126, 17.
[50]	Schwarz F, Eilers C, Kruger L. Materials Characterization, 2015, 105, 144.
[51]	Zha M, Meng X T, Zhang H M, et al. Journal of Alloys and Compounds, 2017, 728, 872.
[52]	Saito Y, Utsunomiya H, Tsuji N, et al. Acta Materialia, 1999, 47(2), 579.
[53]	Wang T Z, Zheng H P, Wu R Z, et al. Advanced Engineering Materials, 2016, 18(2), 304.
[54]	Trojanova Z, Dzugan J, Halmesova K, et al. Acta Physica Polonica A, 2018, 134(3), 863.
[55]	Hou L G, Wang T Z, Wu R Z, et al. Journal of Materials Science & Technology, 2018, 34(2), 317.
[56]	Trojanova Z, Dzugan J, Halmesova K, et al. Materials, 2018, 11(1), 73.
[57]	Drozd Z, Trojanová Z, Halmeová K, et al. Acta Physica Polonica A,2018, 134(3), 820.
[58]	Luo X, Huang T L, Wang Y H, et al. Scientific Reports, 2019, 9(1), 5428.
[59]	Wang H Y, Yu Z P, Zhang L, et al. Scientific Reports, 2015, 5, 17100.
[60]	Rong J, Wang P Y, Zha M, et al. Journal of Alloys and Compounds, 2018, 738, 246.
[61]	Zha M, Zhang X H, Zhang H, et al. Journal of Alloys and Compounds, 2018, 765, 1228.