外加剂对膨胀充填材料性能的影响

材料导报

2022, Vol. 36

Issue (Z1): 20070045-5

高分子与聚合物基复合材料

外加剂对膨胀充填材料性能的影响

姚维^1,2,3, 郑伯坤^1,2, 邱景平³, 黄腾龙^1,2, 尹旭岩^1,2

1 长沙矿山研究院有限责任公司,长沙 410006
2 国家金属采矿工程技术研究中心,长沙 410012
3 东北大学资源与土木工程学院,沈阳 110819

The Influence of Additives on the Properties of Expansion Filling Materials

YAO Wei^1,2,3, ZHENG Bokun^1,2, QIU Jingping³, HUANG Tenglong^1,2, YIN Xuyan^1,2

1 Changsha Mine Research Institute Co., Ltd., Changsha 410006,China
2 National Engineering Research Center for Metal Mining,Changsha 410012, China
3 School of Resources & Civil Engineering, Northeastern University, Shenyang 110819, China

摘要
参考文献
相关文章
推荐阅读
Metrics

下载:

全文 ( PDF ) ( 5736KB )
输出: BibTeX | EndNote (RIS)

摘要充填采矿法因其具有矿石回收率高、矿石损失贫化小以及能有效控制采场地压等优点而在国内外金属矿山得到广泛应用。但充填料浆泌水沉降、空区形状不规则等原因造成充填体不能充分接顶,这将严重影响井下安全生产和地表构筑物的稳定性。为解决此类问题,本工作通过向充填料浆中添加外加剂来制备可以主动接顶的膨胀充填材料,并探讨了外加剂用量对充填料浆的流动性、膨胀充填体的单轴抗压强度(UCS)、表观密度和孔隙率的影响。研究结果表明:在试验选取的掺量范围内,增稠剂、发泡剂会降低充填料浆的流动性和表观密度,当增稠剂掺量为0.6%(质量分数,下同)时,充填体UCS达到最大值1.16 MPa;稳泡剂通过改善气泡稳定性会轻微提高充填体强度,当稳泡剂掺量为0.5%~0.7%时,充填体UCS提高约2.7%;膨胀充填体基本在30 min内停止体积增长,当发泡剂掺量从1.5%增加到3%时,充填体28 d强度和孔隙率相应地降低了37.3%和提高了13.9%。

	服务
	把本文推荐给朋友
	加入引用管理器
	E-mail Alert
	RSS
	作者相关文章
	姚维
	郑伯坤
	邱景平
	黄腾龙
	尹旭岩

关键词: 膨胀充填体料浆流动性孔隙率增稠剂稳泡剂

Abstract: Backfill mining method is widely used in domestic and foreign metal mines due to its advantages such as high ore recovery rate, small ore loss dilution and effective control of mining site pressure. However, the goaf cannot be fully filled due to the bleeding and sedimentation of the filled filler slurry and the irregular shape of the empty area, which will seriously affect the safety of underground production and the stability of surface structures. In order to solve such problems, this work prepared the active top-up of the expansive filler by adding additives to the slurry, and explores the fluidity, UCS,apparent density and porosity of cemented paste backfill (CPB). The results show that within the range of the amount selected in the experiment, the thickener and foaming agent will reduce the fluidity and apparent density of the slurry. When the thickener content is 0.6%(mass fraction, the same below), the UCS content reaches a maximum 1.16 MPa. Foam stabilizer affects the strength of the filler by improving the stability of the bubble. When the content of foam stabilizer is 0.5%—0.7%, the UCS of CPB increases by about 2.7%. The volu-me expansion of the CPB basically stops within 30 min. With foam agent increasing from 1.5% to 3%, the strength(28 d) of CPB decreases by 37.3% and the porosity of CPB increases by 13.9%.

Key words: expansive cemented paste backfill slurry fluidity porosity thickener foam stabilizer

出版日期: 2022-06-05 发布日期: 2022-06-08

ZTFLH:

TD853

基金资助: 国家自然科学基金(51774066);国家重点研发计划项目(2018YFC0604603)

通讯作者: 413778846@qq.com

作者简介: 姚维,助理工程师。2013年9月至2017年6月在江西理工大学获得采矿工程学士学位,2017年9月至2020年1月在东北大学获得采矿工程硕士学位。在国内外学术期刊上发表论文10余篇,研究方向主要为充填采矿技术及矿山固废资源化利用。
郑伯坤,高级工程师。2008年毕业于华北科技学院,获采矿工程学士学位,2011年毕业于长沙矿山研究院,获采矿工程硕士学位。在国内外学术期刊上发表论文30余篇,申请国家发明专利10项,其中授权8项,研究工作主要围绕充填采矿技术开展的充填工艺及充填设备的应用研究,负责科研项目包括十三五重点研发计划课题三“全尾砂充填料深井输送阻力特性与调控技术研究”、山东省重大科技创新工程项目“深井充填高可靠性输送系统与智能控制技术”。

引用本文:

姚维, 郑伯坤, 邱景平, 黄腾龙, 尹旭岩. 外加剂对膨胀充填材料性能的影响[J]. 材料导报, 2022, 36(Z1): 20070045-5.
YAO Wei, ZHENG Bokun, QIU Jingping, HUANG Tenglong, YIN Xuyan. The Influence of Additives on the Properties of Expansion Filling Materials. Materials Reports, 2022, 36(Z1): 20070045-5.

链接本文:

http://www.mater-rep.com/CN/ 或 http://www.mater-rep.com/CN/Y2022/V36/IZ1/20070045

1 蔡美峰,薛鼎龙,任奋华. 工程科学学报,2019,41(4),417.
2 冯帆.岩石力学与工程学报,2019,38(7),1512.
3 靳西传,周宗红,龙刚,等.中国矿业,2019,28(6),104
4 何满潮,谢和平,彭苏萍.岩石力学与工程学报,2005(16),2803.
5 Sellers E J, Klerck P. Tunneling and Underground Space Technology, 2000, 15 (4),463.
6 Sharma R S, Al-Busaidi T S. Engineering Geology, 2001, 60(1-4), 235.
7 杨超,郭利杰,王劼.中国矿业,2019,28(S1),194.
8 谢学斌,李建坤,董宪久,等.岩土力学,2018,39(11),4183.
9 王强,胡世利,邱景平,等.金属矿山,2018(7),50.
10 周乐,许卫军,姚维,等.中国矿业,2019,28(10),138.
11 陆玉根,陈建宏,蒋权,等.矿业研究与开发,2011,31(5),18.
12 Xu S, Suorineni F T, Li K, et al. International Journal of Mining, Reclamation and Environment, 2017, 31(8), 544.
13 胡磊,任高峰,钱兆明,等.金属矿山,2014(11),127.
14 张月侠. 基于膨胀材料的充填接顶技术研究.硕士学位论文,东北大学,2014.
15 Ghasemi Y, Emborg M, Cwirzen A. Materials and Structures, 2019, 52(3), 62.
16 Chen X, Shi X, Zhou J, et al. Construction and Building Materials, 2018, 190(30),211.
17 Fu X, Lai Z, Lai X, et al. Construction and Building Materials,2016,127,712.
18 Tehmina A, Ullah K S, Ahmed M F. The Scientific World Journal, 2014,2014,875082.
19 Sang G, Zhu Y, Yang G, et al. Construction and Building Materials, 2015, 91, 133.
20 雷东移,郭丽萍,孙伟.材料导报:研究篇,2016,30(10),122.
21 左迎峰,王健,肖俊华,等.建筑材料学报,2018,21(3),394.
22 樊丽辉,赵庆国,张君纬,等.河北水利电力学院学报,2019(3),26.
23 Zhao J, Wang X, Peng K, et al. Advances in Materials Science and Engineering, 2017, 2017,1 .
24 Falliano D, De Domenico D, Ricciardi G, et al. Construction and Buil-ding Materials, 2018, 165, 735.
25 殷祥男,王长安,王伟智,等.水泥,2019(S1),145.
26 赵金侠,黄亮,谢建和.中国公路学报,2019,32(7),111.

[1]	刘方, 张昆昆, 罗滔, 马卫卫, 蒋伟. 复杂环境因素下纳米改性混凝土冻融损伤研究[J]. 材料导报, 2022, 36(8): 20100024-5.
[2]	周莹, 穆松, 蒲春平, 周霄骋, 李勇泉, 蔡景顺, 谢德擎. 隧道初支混凝土抗冲刷溶蚀技术评价及作用机理[J]. 材料导报, 2022, 36(4): 20120200-8.
[3]	胡学飞. 低熔点玻璃粉对水冷壁涂层组织和性能的影响[J]. 材料导报, 2021, 35(Z1): 189-194.
[4]	ZEZE Armande Loraine Phalé, 徐红岩, 张默, 马国伟. 环氧树脂-地聚物复合涂层材料耐海水腐蚀性研究[J]. 材料导报, 2021, 35(Z1): 600-606.
[5]	翟建树, 李春燕, 田霖, 卢煜, 寇生中. Fe基非晶涂层耐腐蚀性能的影响因素及提升措施综述[J]. 材料导报, 2021, 35(3): 3129-3140.
[6]	高君华, 黄浩, 曾冲, 郑瑞伦. 孔隙率对传感器多孔电极材料导电性能的影响[J]. 材料导报, 2021, 35(18): 18018-18023.
[7]	曹忠亮, 郭登科, 林国军, 韩振宇, 富宏亚. 热塑性纤维铺放构件的层间剪切强度及孔隙率[J]. 材料导报, 2021, 35(18): 18205-18209.
[8]	郑少军, 刘天乐, 高鹏, 蒋国盛, 冯颖韬, 李丽霞, 陈宇. 固井水泥石孔隙结构演变及力学强度发展规律[J]. 材料导报, 2021, 35(12): 12092-12098.
[9]	李嘉鹏, 李威翰, 刘嘉良, 李永玲, 李飞. 透水路面制品渗透性能的研究进展[J]. 材料导报, 2020, 34(Z2): 265-268.
[10]	张绍康, 王茹, 徐玲琳, 钟世云, 张国防, 王培铭. 羟乙基甲基纤维素改性水泥砂浆的物理力学性能和孔隙率[J]. 材料导报, 2020, 34(Z2): 607-611.
[11]	丁杨, 邓满宇, 周双喜, 王中平, 董晶亮, 魏永起. 基于COMSOL^®模拟材料孔隙率与导热系数的演变关系[J]. 材料导报, 2019, 33(z1): 211-215.
[12]	卢林, 吴文恒, 龙倩蕾, 张亮, 张济山. 喷射成形工艺参数对沉积坯质量的影响[J]. 材料导报, 2019, 33(3): 390-394.
[13]	曹聪聪, 李文亚, 杨康, 李成新, 纪纲. 基体硬度和热学性质对冷喷涂TC4钛合金涂层组织和力学性能的影响[J]. 材料导报, 2019, 33(2): 277-282.
[14]	曹润倬, 周茗如, 周群, 何勇. 超细粉煤灰对超高性能混凝土流变性、力学性能及微观结构的影响[J]. 材料导报, 2019, 33(16): 2684-2689.
[15]	吴其胜,陈宝锐,诸华军,闵治安. 热压制备改性石墨烯-水泥基复合材料:改善微观结构、导热性能和力学性能[J]. 《材料导报》期刊社, 2018, 32(10): 1701-1706.

[1]	Huanchun WU, Fei XUE, Chengtao LI, Kewei FANG, Bin YANG, Xiping SONG. Fatigue Crack Initiation Behaviors of Nuclear Power Plant Main Pipe Stainless Steel in Water with High Temperature and High Pressure[J]. Materials Reports, 2018, 32(3): 373 -377 .
[2]	Miaomiao ZHANG,Xuyan LIU,Wei QIAN. Research Development of Polypyrrole Electrode Materials in Supercapacitors[J]. Materials Reports, 2018, 32(3): 378 -383 .
[3]	Congshuo ZHAO,Zhiguo XING,Haidou WANG,Guolu LI,Zhe LIU. Advances in Laser Cladding on the Surface of Iron Carbon Alloy Matrix[J]. Materials Reports, 2018, 32(3): 418 -426 .
[4]	Huaibin DONG,Changqing LI,Xiahui ZOU. Research Progress of Orientation and Alignment of Carbon Nanotubes in Polymer Implemented by Applying Electric Field[J]. Materials Reports, 2018, 32(3): 427 -433 .
[5]	Xiaoyu ZHANG,Min XU,Shengzhu CAO. Research Progress on Interfacial Modification of Diamond/Copper Composites with High Thermal Conductivity[J]. Materials Reports, 2018, 32(3): 443 -452 .
[6]	Anmin LI,Junzuo SHI,Mingkuan XIE. Research Progress on Mechanical Properties of High Entropy Alloys[J]. Materials Reports, 2018, 32(3): 461 -466 .
[7]	Qingqing DING,Qian YU,Jixue LI,Ze ZHANG. Research Progresses of Rhenium Effect in Nickel Based Superalloys[J]. Materials Reports, 2018, 32(1): 110 -115 .
[8]	Yaxiong GUO,Qibin LIU,Xiaojuan SHANG,Peng XU,Fang ZHOU. Structure and Phase Transition in CoCrFeNi-M High-entropy Alloys Systems[J]. Materials Reports, 2018, 32(1): 122 -127 .
[9]	Changsai LIU,Yujiang WANG,Zhongqi SHENG,Shicheng WEI,Yi LIANG,Yuebin LI,Bo WANG. State-of-arts and Perspectives of Crankshaft Repair and Remanufacture[J]. Materials Reports, 2018, 32(1): 141 -148 .
[10]	Xia WANG,Liping AN,Xiaotao ZHANG,Ximing WANG. Progress in Application of Porous Materials in VOCs Adsorption During Wood Drying[J]. Materials Reports, 2018, 32(1): 93 -101 .

Viewed

Full text

Abstract

Cited

Shared

Discussed