Please wait a minute...
《材料导报》期刊社  2018, Vol. 32 Issue (9): 1401-1411    https://doi.org/10.11896/j.issn.1005-023X.2018.09.002
  材料与可持续发展(一)—— 面向洁净能源的先进材料 |
锂硫电池硫正极材料研究进展
陈子冲,方如意,梁 初,甘永平,张文魁
浙江工业大学材料科学与工程学院, 杭州 310014
Recent Progress in Sulfur Cathode for Li-S Batteries
CHEN Zichong, FANG Ruyi, LIANG Chu, GAN Yongping, ZHANG Wenkui
College of Materials Science and Engineering, Zhejiang University of Technology, Hangzhou 310014
下载:  全 文 ( PDF ) ( 2082KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 由化石燃料的大量使用导致的全球能源和环境问题日益严重,已对人们的生产和生活产生了明显的影响。开发利用储量丰富的清洁能源(如太阳能、水能和风能等)有望较好地解决全球能源和环境问题。由于这些清洁能源存在地域性、间歇性等特点,高效的能量转化和存储技术是实现清洁能源规模化利用的关键和基础。锂离子电池作为绿色环保的储能器件,已在手机、笔记本电脑、相机等便携电子产品中广泛使用。近年来,锂离子电池开始在电动汽车等动力电池领域得到应用。但是,由于其能量密度不够高,导致锂离子电池电动汽车续航短、充电频繁及购车成本高。由金属锂为负极和硫为正极组成的锂硫电池的能量密度(2 600 Wh·kg-1)远高于目前广泛使用的锂离子电池。此外,硫正极材料具有储量丰富、毒性低、价格便宜、环境友好等突出优点。因此,锂硫电池被认为是当前最具研究前景的高能量密度二次电池之一。   硫正极材料的本征导电性差、在充放电过程中存在较大的体积膨胀和收缩,储放锂过程中形成的多硫化锂易溶于电解液,使得锂硫电池的倍率性能、循环寿命和库伦效率等电化学性能离实际应用仍有较大距离。迄今为止,关于硫正极材料的研究工作,主要集中于如何提升其导电性、抑制或消除由多硫化锂的溶解引起的穿梭效应以及在反复的循环过程中保持电极材料微结构的稳定性等方面。   相关研究表明,将硫与不同形貌的碳材料复合构筑成具有特殊微观结构的硫/碳复合正极材料可显著提高其导电性、抑制多硫化锂的穿梭效应和减缓储放锂前后的体积变化,进而改善倍率性能、循环稳定性和充放电效率等。此外,在硫正极材料中引入异质元素掺杂碳材料、金属氧化物和导电集合物均可通过化学吸附实现对易溶解多硫化锂的有效吸附。将上述多种改性方法结合也可使硫正极材料具有优异的电化学储锂性能。   本文从锂硫电池的工作原理出发,总结了硫正极材料存在的主要问题,综述了近几年锂硫电池复合正极材料的研究进展,最后对锂硫电池正极材料的研究思路与发展趋势进行了分析和展望。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
陈子冲
方如意
梁 初
甘永平
张文魁
关键词:  锂硫电池  硫正极  复合材料  电化学性能    
Abstract: The global energy and environmental problems caused by the extensive use of fossil fuels have significantly impac-ted on the human’s production and livelihoods, which can be expected to well address via developing and utilizing various clean energy sources, such as solar energy, water energy and wind energy, etc. Efficient energy conversion and storage technologies are the key and basics of the large-scale use of clean energy due to their regional and intermittent characteristics. Lithium-ion batteries, as green energy storage devices, are widely used in mobile phones, laptops, cameras and other portable electronic devices. In recent years, lithium-ion batteries have begun to be applied in the field of power batteries such as electric vehicles. However, the electric vehicles suffer from inferior cruise-ability, frequent charging and high cost because of their relatively low energy density. The energy density (2 600 Wh·kg-1) of lithium-sulfur batteries, composed of lithium metal as anode and sulfur as cathode, is much higher than that of state-of-the-art lithium-ion batteries. Additionally, the sulfur cathode material is abundant, nontoxic, cost effectiveness and environmental friendliness. Hence, lithium-sulfur batteries are considered as one of the most promising secondary batteries.   However, the poor CE and limited cycle life, caused by the fundamental defects of sulfur cathode such as low ionic/electronic conductivities, large volumetric expansion and shuttle effect, hamper the widespread application of Li-S battery. So far, considerable studies have focused on enhancing the conductivity, inhibiting or eliminating the shuttle effect and stabilizing the microstructure of electrode material during repeated cycles.   It has been demonstrated that the S/C composite cathode materials with special microstructure, prepared by compositing sulfur and carbon with different morphology, exhibit significantly improved conductivity, decreased shuttle effect of lithium polysulfide and less volume change during lithium intercalation/deintercalation. These improvements lead to better rate performance, cycling stability and charge-discharge efficiency. Moreover, the introduction of heterogeneous element-doped carbon materials, metal oxides and conductive polymers in the sulfur cathode material can achieve effective chemical adsorption of lithium polysulfide. Excellent electrochemical lithium storage performance of sulfur cathode can also be achieved by the combination of these various modification me-thods.   In this review, the main problems and recent research progress in sulfur cathode materials are summarized and commented upon based on the principle of lithium-sulfur batteries. Meanwhile, it also gives brief suggestions and outlooks on the future research directions in lithium-sulfur batteries.
Key words:  lithium-sulfur batteries    sulfur cathode    composite    electrochemical performance
               出版日期:  2018-05-10      发布日期:  2018-07-06
ZTFLH:  O646  
基金资助: 国家自然科学基金(21403196;51572240;51677170);浙江工业大学课堂教学改革项目(KG201603);2017年国家级大学生创新创业训练计划项目(201710337003)
作者简介:  陈子冲:男,1996年生,硕士研究生,主要从事二次锂离子电池的研究 E-mail:512488142@qq.com 梁初:男,1980年生,副教授,主要从事二次电池的电极材料、高容量储氢材料的研究 Tel:0571-88320873 E-mail:cliang@zjut.edu.cn 张文魁:男,1969年生,教授,博士研究生导师,主要从事二次电池的关键材料的研究 Tel:0571-88320394 E-mail:msechem@zjut.edu.cn
引用本文:    
陈子冲, 方如意, 梁 初, 甘永平, 张文魁. 锂硫电池硫正极材料研究进展[J]. 《材料导报》期刊社, 2018, 32(9): 1401-1411.
CHEN Zichong, FANG Ruyi, LIANG Chu, GAN Yongping, ZHANG Wenkui. Recent Progress in Sulfur Cathode for Li-S Batteries. Materials Reports, 2018, 32(9): 1401-1411.
链接本文:  
http://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2018.09.002  或          http://www.mater-rep.com/CN/Y2018/V32/I9/1401
1 Schlapbach L, Züttel A. Hydrogen-storage materials for mobile applications[J].Nature,2001,414(6861):353.
2 Palacín M R. Recent advances in rechargeable battery materials:A chemist’s perspective[J].Chemical Society Reviews,2009,38(9):2565.
3 Trudeau M L. Advancedmaterials for energy storage [J].MRS Bulletin,1999,24(11):23.
4 Whittingham M S. Lithium batteries and cathode materials[J].Chemical Reviews,2004,104(10):4271.
5 Winter M, Besenhard J O, Spahr M E, et al. Insertionelectrode materials for rechargeable lithium batteries[J].Advanced Materials,2010,10(10):725.
6 Padhi A K, Nanjundaswamy K S, Masquelier C, et al. Effect ofstructure on the Fe3+/Fe2+ redox couple in iron phosphates[J].Journal of the Electrochemical Society,1997,144(5):1609.
7 Chung S Y, Blocking J T, Andersson A S, et al. Electronically conductive phospho-olivines as lithium storage electrodes[J].Nature Materials,2002,1(2):123.
8 Kang B, Ceder G. Battery materials for ultrafast charging and discharging[J].Nature,2009,458(7235):190.
9 Yao Z D, Wei W, Wang J L, et al. Review ofsulfur-based cathodes for high performance lithium rechargeable batteries[J].Acta Physico-Chimica Sinica,2011,27(5):1005(in Chinese).
姚真东,魏巍,王久林,等.锂硫二次电池正极研究进展[J].物理化学学报,2011,27(5):1005.
10 Liang X, Wen Z Y, Liu Y. New development of key materials for high-performance lithium-sulfur batteries[J].Progress in Chemistry,2011,23(z1):520(in Chinese).
梁宵,温兆银,刘宇.高性能锂硫电池材料研究进展[J].化学进展,2011,23(z1):520.
11 Ji X, Nazar L F. Advances in Li-S batteries[J].Journal of Materials Chemistry,2010,20(44):9821.
12 Jacobson M Z. Review of solutions to global warming, air pollution, and energy security[J].Energy & Environmental Science,2009,2(2):148.
13 Song M K, Zhang Y, Cairns E J. A long-life, high-rate lithium/sulfur cell:A multifaceted approach to enhancing cell performance[J].Nano Letters,2013,13(12):5891.
14 Marmorstein D, Yu T H, Striebel K A. Electrochemicalperformance of lithium/sulfur cells with three different polymer electrolytes[J].Journal of Power Sources,2000,89(2):219.
15 Dejonghe L C, Mayying C, Katz B D, et al. High capacity/high discharge rate rechargeable positive electrode: US, 6200704[P].2001-03-13.
16 Xu Z S, Terjea S, Yordanm G. Electrochemical cells with high volumetric density if electroactive sulfur-containing materials in cathode active layers: US, 6302928[P].2001-10-16.
17 Yamin H, Peled E. Electrochemistry of a nonaqueous lithium/sulfur cell[J].Journal of Power Sources,1983,9(3):281.
18 Bruce P G, Freunberger S A, Hardwick L J, et al. Li-O2 and Li-S batteries with high energy storage[J].Nature Materials,2012,11(1):19.
19 Mikhaylik Y V, Akridge J R. Polysulfideshuttle study in the Li/S battery system[J].Journal of the Electrochemical Society,2004,151:A1969.
20 Zhang S S. Liquid electrolyte lithium/sulfur battery: Fundamental chemistry, problems, and solutions[J].Journal of Power Sources,2013,231(2):153.
21 Manthiram A, Fu Y, Chung S H, et al. Rechargeable lithium-sulfur batteries[J].Chemical Reviews,2014,114(23):11751.
22 Kumaresan K, Mikhaylik Y, White R E. Amathematical model for a lithium-sulfur cell[J].Journal of the Electrochemical Society,2008,155(8):A576.
23 Yang Y, Zheng G, Cui Y. Nanostructured sulfur cathodes[J].Che-mical Society Reviews,2013,42(7):3018.
24 Zhang S S. Role of LiNO3, in rechargeable lithium/sulfur battery[J].Electrochimica Acta,2012,70(6):344.
25 Walus' S, Barchasz C, Colin J F, et al. New insight into the working mechanism of lithium-sulfur batteries:In situ and operando X-ray diffraction characterization[J].Chemical Communications,2013,49(72):7899.
26 Ji X, Lee K T, Nazar L F. A highly ordered nanostructured carbon-sulphur, cathode for lithium-sulphur batteries[J].Nature Materials,2009,8(6):500.
27 Liang C, Dudney N J, Howe J Y. Hierarchicallystructured sulfur/carbon nanocomposite material for high-energy lithium battery[J].Chemistry of Materials,2009,21(19):4724.
28 Zhang B, Qin X, Li G R, et al. Enhancement of long stability of sulfur cathode by encapsulating sulfur into micropores of carbon spheres[J].Energy & Environmental Science,2010,3(10):1531.
29 Wang L, Zhao Y, Thomas M L, et al. In situ synthesis of bipyramidal sulfur with 3d carbon nanotube framework for lithium-sulfur batteries[J].Advanced Functional Materials,2014,24(15):2248.
30 Zhang S M, Zhang Q, Huang J Q, et al. Composite cathodes containing SWCNT@S coaxial nanocables: facile synthesis, surface modification, and enhanced performance for Li-ion storage[J].Particle & Particle Systems Characterization,2013,30(2):158.
31 Zheng G, Yang Y, Cha J J, et al. Hollowcarbon nanofiber-encapsulated sulfur cathodes for high specific capacity rechargeable lithium batteries[J].Nano Letters,2011,11(10):4462.
32 Ji L, Rao M, Aloni S, et al. Porous carbon nanofiber-sulfur compo-site electrodes for lithium/sulfur cells[J].Energy & Environmental Science,2011,4(12):5053.
33 Cao J, Chen C, Zhao Q, et al. Aflexible nanostructured paper of a reduced graphene oxide-sulfur composite for high-performance li-thium-sulfur batteries with unconventional configurations[J].Advanced Materials,2016,28(43):9629.
34 Zhao M Q, Zhang Q, Huang J Q, et al. Unstacked double-layer templated graphene for high-rate lithium-sulphur batteries[J].Nature Communications,2014,5(5):3410.
35 Xi K, Kidambi P R, Chen R, et al. Binder free three-dimensional sulphur/few-layer graphene foam cathode with enhanced high-rate capability for rechargeable lithium sulphur batteries[J].Nanoscale,2014,6(11):5746.
36 Jayaprakash N, Shen J, Moganty S S, et al. Poroushollow carbon@sulfur composites for high-power lithium-sulfur batteries[J].Angewandte Chemie,2011,50(26):5904.
37 Tao X, Zhang J, Xia Y, et al. Bio-inspired fabrication of carbon nanotiles for high performance cathode of Li-S batteries[J].Journal of Materials Chemistry A,2014,2(7):2290.
38 Li X, Cao Y, Qi W, et al. Optimization of mesoporous carbon structures for lithium-sulfur battery applications[J].Journal of Materials Chemistry,2011,21(41):16603.
39 Tao X, Chen X, Xia Y, et al. Highly mesoporous carbon foams synthesized by a facile, cost-effective and template-free Pechini method for advanced lithium-sulfur batteries[J].Journal of Materials Che-mistry A,2013,1(10):3295.
40 Shinae Jun, Hoon Joo S, Ryong Ryoo, et al. Synthesis ofnew, nanoporous carbon with hexagonally ordered mesostructure[J].Journal of the American Chemical Society,2014,122(43):10712.
41 Xin S, Gu L, Zhao N H, et al. Smaller sulfur molecules promise better lithium-sulfur batteries[J].Journal of the American Chemical Society,2012,134(45):18510.
42 Ryu H, Park J, Park J, et al. High capacity cathode materials for Li-S batteries[J].Journal of Materials Chemistry A,2013,1(5):1573.
43 Vu A, Qian Y, Stein A. Porouselectrode materials for lithium-ion batteries-How to prepare them and what makes them special[J].Advanced Energy Materials,2012,2(9):1056.
44 Su L, Jing Y, Zhou Z. Li ion battery materials with core-shell nanostructures[J].Nanoscale,2011,3(10):3967.
45 Chen L, Shaw L L. Recent advances in lithium-sulfur batteries[J].Journal of Power Sources,2014,267(3):770.
46 Fu Y, Manthiram A. Core-shell structured sulfur-polypyrrole composite cathodes for lithium-sulfur batteries[J].RSC Advances,2012,2(14):5927.
47 Chen H, Dong W, Ge J, et al. Ultrafinesulfur nanoparticles in conducting polymer shell as cathode materials for high performance lithium/sulfur batteries[J].Scientific Reports,2013,3(5):1910.
48 Zhou W, Yu Y, Chen H, et al. Yolk-shell structure of polyaniline-coated sulfur for lithium-sulfur batteries[J].Journal of the American Chemical Society,2013,135(44):16736.
49 Zhang C, Wu H B, Yuan C, et al. Confining sulfur in double-shelled hollow carbon spheres for lithium-sulfur batteries[J].Angewandte Chemie International Edition,2012,51(38):9592.
50 Zhi W S, Li W, Cha J J, et al.Sulphur-TiO2 yolk-shell nanoarchitecture with internal void space for long-cycle lithium-sulphur batteries[J].Nature Communications,2013,4(4):1331.
51 Che G, Lakshmi B B, Martin C R, et al. Chemicalvapor deposition based synthesis of carbon nanotubes and nanofibers using a template method[J].Chemistry of Materials,1998,10(1):260.
52 Che G, Lakshmi B B, Fisher E R, et al. Carbon nanotubule membranes for electrochemical energy storage and production[J].Nature,1998,393(6683):346.
53 Che G, Jirage K B, Fisher E R, et al. Chemical-vapor deposition-based template synthesis of microtubular TiS2 battery electrodes[J].Journal of the Electrochemical Society,1997,144:4296.
54 Park M H, Kim M G, Joo J, et al. Siliconnanotube battery anodes[J].Nano Letters,2009,9(11):3844.
55 Xiao L, Damien J, Luo J, et al. Crumpled graphene particles for microbial fuel cell electrodes[J].Journal of Power Sources,2012,208(2):187.
56 Jiang L, Fan Z. Design of advanced porous graphene materials:From graphene nanomesh to 3D architectures[J].Nanoscale,2014,6(4):1922.
57 Liu G, Wang Y, Xu C, et al. Excellent catalytic effects of highly crumpled graphene nanosheets on hydrogenation/dehydrogenation of magnesium hydride[J].Nanoscale,2013,5(3):1074.
58 Zang J, Ryu S, Pugno N, et al. Multifunctionality and control of the crumpling and unfolding of large-area graphene[J].Nature Mate-rials,2013,12(4):321.
59 Cranford S W, Buehler M J. Packing efficiency and accessible surface area of crumpled graphene[J].Physical Review B Condensed Matter,2011,84(20):5324.
60 Wu Z S, Zhou G, Yin L C, et al. Graphene/metal oxide composite electrode materials for energy storage[J].Nano Energy,2012,1(1):107.
61 Wang X, Zhi L, Tsao N, et al. Transparent carbon films as electrodes in organic solar cells[J].Angewandte Chemie International Edition,2008,47(16):2990.
62 Zhang K, Zhang L L, Zhao X S, et al. Graphene/polyaniline nanofiber composites as supercapacitor electrodes[J].Chemistry of Mate-rials,2010,22(4):1392.
63 Yan J, Wei T, Shao B, et al. Electrochemical properties of graphene nanosheet/carbon black composites as electrodes for supercapacitors[J].Carbon,2010,48(6):1731.
64 Fan Z, Yan J, Zhi L, et al. A three-dimensional carbon nanotube/graphene sandwich and its application as electrode in supercapacitors[J].Advanced Materials,2010,22(33):3723.
65 Zhu Y, Li L, Zhang C, et al. A seamless three-dimensional carbon nanotube graphene hybrid material[J].Nature Communications,2012,3(3):1225.
66 Zhao M, Liu X, Zhang Q, et al. Graphene/single-walled carbon nanotube hybrids:One-step catalytic growth and applications for high-rate Li-S batteries[J].ACS Nano,2012,6(12):10759.
67 Peng H, Huang J, Zhao M, et al. Nanoarchitecturedgraphene/CNT@porous carbon with extraordinary electrical conductivity and interconnected micro/mesopores for lithium-sulfur batte-ries[J].Advanced Functional Materials,2014,24(19):2772.
68 Chen Z, Ren W, Gao L, et al. Three-dimensional flexible and conductive interconnected graphene networks grown by chemical vapour deposition[J].Nature Materials,2011,10(6):424.
69 Kidambi P R, Bayer B C, Weatherup R S, et al. Hafnia nanoparticles-A model system for graphene growth on a dielectric[J].Physica Status Solidi-rapid Research Letters,2011,5(9):341.
70 Kidambi P R, Ducati C, Dlubak B, et al. Theparameter space of graphene chemical vapor deposition on polycrystalline Cu[J].Journal of Physical Chemistry C,2012,116(42):22492.
71 Song J, Xu T, Gordin M L, et al. Nitrogen-doped mesoporous carbon promoted chemical adsorption of sulfur and fabrication of high-areal-capacity sulfur cathode with exceptional cycling stability for lithium-sulfur batteries[J].Advanced Functional Materials,2014,24(9):1243.
72 Song J, Gordin M L, Xu T, et al. Stronglithium polysulfide chemisorption on electroactive sites of nitrogen-doped carbon composites for high-performance lithium-sulfur battery cathodes[J].Angewandte Chemie,2015,54(14):4325.
73 Sun X, Wang X, Mayes R T, et al. Lithium-sulfur batteries based on nitrogen-doped carbon and an ionic-liquid electrolyte[J].Chemsuschem,2012,5(10):2079.
74 Xia Y, Fang R, Xiao Z, et al. Confiningsulfur in N-doped porous carbon microspheres derived from microalgaes for advanced lithium-sulfur batteries[J].ACS Applied Materials & Interfaces,2017,9(28):23782.
75 Zhou W, Wang C, Zhang Q, et al. Tailoringpore size of nitrogen-doped hollow carbon nanospheres for confining sulfur in lithium-sulfur batteries[J].Advanced Energy Materials,2015,5(16):1401752.
76 Xiao J, Wang H, Li X, et al. N-doped carbon nanotubes as cathode material in Li-S batteries[J].Journal of Materials Science: Materials in Electronics,2015,26(10):7895.
77 Li Y, Mi R, Li S, et al. Sulfur-nitrogen doped multi walled carbon nanotubes composite as a cathode material for lithium sulfur batte-ries[J].International Journal of Hydrogen Energy,2014,39(28):16073.
78 Zhao Y, Yin F, Zhang Y, et al. Afree-standing sulfur/nitrogen-doped carbon nanotube electrode for high-performance lithium/sulfur batteries[J].Nanoscale Research Letters,2015,10(1):450.
79 Zhao X, Liu Y, Manuel J, et al. Nitrogen-doped mesoporous carbon: A top-down strategy to promote sulfur iImmobilization for lithium-sulfur batte-ries[J].Chemsuschem,2015,8(19):3234.
80 Sun F, Wang J, Chen H, et al. Highefficiency immobilization of sulfur on nitrogen-enriched mesoporous carbons for Li-S batteries[J].ACS Applied Materials & Interfaces,2013,5(12):5630.
81 Qiu Y, Li W, Zhao W, et al. High-rate, ultralong cycle-life lithium/sulfur batteries enabled by nitrogen-doped graphene[J].Nano Letters,2014,14(8):4821.
82 Wang X, Zhang Z, Qu Y, et al. Nitrogen-doped graphene/sulfur composite as cathode material forhigh capacity lithium-sulfur batte-ries[J].Journal of Power Sources,2014,256(12):361.
83 Song J, Yu Z, Gordin M L, et al. Advancedsulfur cathode enabled by highly crumpled nitrogen-doped graphene sheets for high-energy-density lithium-sulfur batteries[J].Nano Letters,2016,16(2):864.
84 Yang J, Wang S, Ma Z, et al. Novel nitrogen-doped hierarchically porous coralloid carbon materials as host matrixes for lithium-sulfur batteries[J].Electrochimica Acta,2015,159:8.
85 Tang C, Zhang Q, Zhao M, et al. Nitrogen-doped aligned carbon nanotube/graphene sandwiches: Facile catalytic growth on bifunctional natural catalysts and their applications as scaffolds for high-rate lithium-sulfur batteries[J].Advanced Materials,2014,26(35):6100.
86 Ding Y L, Kopold P, Hahn K, et al. Facile solid-state growth of 3D well-interconnected nitrogen-rich carbon nanotube-graphene hybrid architectures for lithium-sulfur batteries[J].Advanced Functional Materials,2016,26(7):1112.
87 Yang C P, Yin Y X, Ye H, et al. Insight into the effect of boron doping on sulfur/carbon cathode in lithium-sulfur batteries[J].ACS Applied Materials & Interfaces,2014,6(11):8789.
88 Wu F, Qian J, Wu W, et al.Boron-doped microporous nano carbon as cathode material for high-performance Li-S batteries[J].Nano Research,2017,10(2):426.
89 Chen F, Yang J, Bai T, et al. Biomass waste-derived honeycomb-like nitrogen and oxygen dual-doped porous carbon for high perfor-mance lithium-sulfur batteries[J].Electrochimica Acta,2016,192:99.
90 Pang Q, Tang J, Huang H, et al. Anitrogen and sulfur dual-doped carbon derived from polyrhodanine@cellulose for advanced lithium-sulfur batteries[J].Advanced Materials,2015,27(39):6021.
91 Zhou G, Paek E, Hwang G S, et al. Long-life Li/polysulphide batteries with high sulphur loading enabled by lightweight three-dimensional nitrogen/sulphur-codoped graphene sponge[J].Nature Communications,2015,6:7760.
92 Wohlgemuth S A, White R J, Willinger M G, et al. A one-pot hydrothermal synthesis of sulfur and nitrogen doped carbon aerogels with enhanced electrocatalytic activity in the oxygen reduction reaction[J].Green Chemistry,2012,14(5):1515.
93 Chen C Y, Tang C, Wang H F, et al. Nitrogen andphosphorus dual-doped graphene-based porous carbon for high-performance lithium-sulfur batteries[C]∥Conference Record of the 2016 30th Annual Conference of Chinese Chemical Society.Dalian,2016(in Chinese).
陈琛煜,唐城,王浩帆,等.氮、磷共掺杂石墨烯作为超高循环稳定性锂硫电池正极材料[C]∥中国化学会第30届学术年会摘要集.大连,2016.
94 Yuan S, Bao J L, Wang L, et al. Graphene-supported nitrogen and boron rich carbon layer for improved performance of lithium-sulfur batteries due to enhanced chemisorption of lithium polysulfides[J].Advanced Energy Materials,2016,6(5):1501733.
95 Jin C, Zhang W, Zhuang Z, et al. Enhanced sulfide chemisorption using boron and oxygen dually doped multi-walled carbon nanotubes for advanced lithium-sulfur batteries[J].Journal of Materials Che-mistry A,2016,5(2):632.
96 Song M S, Han S C, Kim H S, et al. Effects ofnanosized adsorbing material on electrochemical properties of sulfur cathodes for Li/S secondary batteries[J].Journal of the Electrochemical Society,2004,151(6):A791.
97 Zhang Y, Zhao Y, Yermukhambetova A, et al. Ternary sulfur/polyacrylonitrile/Mg0.6Ni0.4O composite cathodes for high perfor-mance lithium/sulfur batteries[J].Journal of Materials Chemistry A,2012,1(2):295.
98 Choi Y J, Jung B S, Lee D J, et al. Electrochemical properties of sulfur electrode containing nano Al2O3 for lithium/sulfur cell[J].Physica Scripta,2007,2007(T129):62.
99 Ji X, Evers S, Black R, et al. Stabilizing lithium-sulphur cathodes using polysulphide reservoirs[J].Nature Communications,2011,2:325.
100 Evers S, Yim T, Nazar L F. Understanding thenature of absorption/adsorption in nanoporous polysulfide sorbents for the Li-S battery[J].Journal of Physical Chemistry C,2012,116(37):19653.
101 Liang X, Kwok C Y, Lodi-Marzano F, et al. Tuning transition metal oxide-sulfur interactions for long life lithium-sulfur batteries: The “Goldilocks” principle[J].Advanced Energy Materials,2016,6:1501636.
102 Liang X, Nazar L F. Insitu reactive assembly of scalable core-shell sulfur-MnO2 composite cathodes[J].ACS Nano,2016,10(4):4192.
103 Lee J, Hwang T, Lee Y, et al. Coating of sulfur particles with manganese oxide nanowires as a cathode material in lithium-sulfur batteries[J].Materials Letters,2015,158:132.
104 Wang S, Yang Z, Zhang H, et al. Mesoporous β-MnO2/sulfur composite as cathode material for Li-S batteries[J].Electrochimica Acta,2013,106:307.
105 Zhang J, Shi Y, Ding Y, et al. Insitu reactive synthesis of polypyrrole-MnO2 coaxial nanotubes as sulfur hosts for high-performance lithium-sulfur battery[J].Nano Letters,2016,16(11):7276.
106 Cao K, Liu H, Li Y, et al. Encapsulating sulfur in δ-MnO2, at room temperature for Li-S battery cathode[J].Energy Storage Materials,2017,9:78.
107 Pang Q, Kundu D, Cuisinier M, et al. Surface-enhanced redox chemistry of polysulphides on a metallic and polar host for lithium-sulphur batteries[J].Nature Communications,2014,5:4759.
108 Tao X, Wang J, Ying Z, et al. Strong sulfur binding with conducting Magnéli-phase TinO2n-1 nanomaterials for improving lithium-sulfur batteries[J].Nano Letters,2014,14(9):5288.
109 Li J, Ding B, Xu G, et al. Enhanced cycling performance and electrochemical reversibility of a novel sulfur-impregnated mesoporous hollow TiO2 sphere cathode for advanced Li-S batteries[J].Nanoscale,2013,5(13):5743.
110 Ma X Z, Jin B, Wang H Y, et al. S-TiO2, composite cathode materials for lithium/sulfur batteries[J]. Journal of Electroanalytical Chemistry,2015,736:127.
111 Li Q, Zhang Z, Zhang K, et al. Synthesis and electrochemical performance of TiO2-sulfur composite cathode materials for lithium-sulfur batteries[J].Journal of Solid State Electrochemistry,2013,17(11):2959.
112 Xie K, Han Y, Wei W, et al. Fabrication of a novel TiO2/S composite cathode for high performance lithium-sulfur batteries[J].RSC Advances,2015,5(94):77348.
113 Smith J R, Walsh F C, Clarke R L. Electrodes based on Magnéli phase titanium oxides:The properties and applications of Ebonex materials[J].Journal of Applied Electrochemistry,1998,28(10):1021.
114 Liu X, Huang J Q, Zhang Q, et al. Nanostructuredmetal oxides and sulfides for lithium-sulfur batteries[J].Advanced Materials,2017,29(20):1601759.
115 Tao X, Wang J, Liu C, et al. Balancing surface adsorption and diffusion of lithium-polysulfides on nonconductive oxides for lithium-sulfur battery design[J].Nature Communications,2016,7:11203.
116 Wang J, Chen J, Konstantinov K, et al. Sulphur-polypyrrole composite positive electrode materials for rechargeable lithium batteries[J].Electrochimica Acta,2006,51(22):4634.
117 Sun M, Zhang S, Jiang T, et al. Nano-wire networks of sulfur-polypyrrole composite cathode materials for rechargeable lithium batteries[J].Electrochemistry Communications,2008,10(12):1819.
118 Xiao L, Wen Z, Yu L, et al. Preparation and characterization of sulfur-polypyrrole composites with controlled morphology as high capacity cathode for lithium batteries[J].Solid State Ionics,2011,192(1):347.
119 Liang X, Liu Y, Wen Z, et al. A nano-structured and highly ordered polypyrrole-sulfur cathode for lithium-sulfur batteries[J].Journal of Power Sources,2011,196(16):6951.
120 Liang X, Wen Z, Liu Y, et al. A composite of sulfur and polypyrrole-multi walled carbon combinatorial nanotube as cathode for Li/S battery[J].Journal of Power Sources,2012,206(1):409.
121 Ma P, Zhang B H, Xu Y H, et al. Study on improving properties of elemental sulfur cathode materials by coating PANi[J].Modern Chemical Industry,2007,27(3):30(in Chinese).
马萍,张宝宏,徐宇虹,等.聚苯胺包覆对提高单质硫正极材料的性能研究[J].现代化工,2007,27(3):30.
122 Xiao L, Cao Y, Xiao J, et al. A soft approach to encapsulate sulfur: Polyaniline nanotubes for lithium-sulfur batteries with long cycle life[J].Advanced Materials,2012,24(9):1176.
123 Wang J, Yang J, Xie J, et al. Anovel conductive polymer-sulfur composite cathode material for rechargeable lithium batteries[J].Advanced Materials,2002,14(13-14):963.
124 Wang J, Yang J, Wan C, et al. Sulfurcomposite cathode materials for rechargeable lithium batteries[J].Advanced Functional Mate-rials,2003,13(6):487.
125 Yu X, Xie J, Li Y, et al. Stable-cycle and high-capacity conductive sulfur-containing cathode materials for rechargeable lithium batte-ries[J].Journal of Power Sources,2005,146(1-2):335.
126 Wu F, Wu S, Chen R, et al. Sulfur-polythiophene composite ca-thode materials for rechargeable lithium batteries[J].Electrochemical and Solid-State Letters,2010,13(4):A29.
127 Wu F, Chen J, Chen R, et al. Sulfur/polythiophene with a core/shell structure: Synthesis and electrochemical properties of the cathode for rechargeable lithium batteries[J].Journal of Physical Chemistry C,2011,115(13):6057.
128 Holten-Andersen N, Harrington M J, Birkedal H, et al. pH-induced metal-ligand cross-links inspired by mussel yield self-healing polymer networks with near-covalent elastic moduli[J].Proceedings of the National Academy of Sciences of the United States of America,2011,108(7):2651.
129 Hager M D, Peter G, Christoph L, et al. Self-healing materials[J].Advanced Materials,2010,22(47):5424.
130 Su Y Z, Guo S H, Xiao Y Z, et al. Electrode kinetics of 2, 2′-diaminophenyloxydisulfide[J].Acta Physico-Chimica Sinica,2004,20(5):518(in Chinese).
苏育志,郭仕恒,萧翼之,等.2,2′-二氨基苯氧基二硫化物的电极过程动力学研究[J].物理化学学报,2004,20(5):518.
131 Yu Xianguo. Structure, performance and lithium storage mechanism of conductive sulfur-containing polymers[D].Shanghai:Shanghai Institute of Microsystem and Information Technology,2005(in Chinese).
喻献国.导电含硫聚合物的结构与性能及储锂机理研究[D].上海:上海微系统与信息技术研究所,2005.
132 Yu X G, Xie J Y, Huang H J, et al. Characterization and electrochemical performance of conductive sulfur-containing polymer as cathode material for rechargeable lithium batteries[J].The Chinese Journal of Nonferrous Metals,2004,14(s2):355(in Chinese).
喻献国,解晶莹,黄海江,等.二次锂电池用导电含硫聚合物正极材料的结构表征及电化学性能[J].中国有色金属学报,2004,14(s2):355.
133 Yin L, Wang J, Yang J, et al. A novel pyrolyzed polyacrylonitrile-sulfur@MWCNT composite cathode material for high-rate rechargeable lithium/sulfur batteries[J].Journal of Materials Chemistry,2011,21(19):6807.
134 Wu F, Chen J, Li L, et al. Improvement ofrate and cycle perfor-mance by rapid polyaniline coating of a MWCNT/sulfur cathode[J].Journal of Physical Chemistry C,2013,115(49):24411.
135 Li G C, Li G R, Ye S H, et al. Apolyaniline-coated sulfur/carbon composite with an enhanced high-rate capability as a cathode material for lithium/sulfur batteries[J].Advanced Energy Materials,2012,2(10):1238.
136 Wang M, Wang W, Wang A, et al. A multi-core-shell structured composite cathode material with a conductive polymer network for Li-S batteries[J].Chemical Communications,2013,49(87):10263.
137 Zheng G, Zhang Q, Cha J J, et al. Amphiphilic surface modification of hollow carbon nanofibers for improved cycle life of lithium sulfur batteries[J].Nano Letters,2013,13(3):1265.
138 Yang Y, Yu G, Cha J J, et al. Improving theperformance of lithium-sulfur batteries by conductive polymer coating[J].ACS Nano,2011,5(11):9187.
139 Li W, Zhang Q, Zheng G, et al. Understanding the role of different conductive polymers in improving the nanostructured sulfur cathode performance[J].Nano Letters,2013,13(11):5534.
[1] 封平净, 卢鹏, 刘耀春, 何玉林. 不同nLi/nM值制备富锂锰基正极材料及其电化学性能[J]. 材料导报, 2019, 33(z1): 50-52.
[2] 洪起虎, 燕绍九, 陈翔, 李秀辉, 舒小勇, 吴廷光. GO添加量对RGO/Cu复合材料组织与性能的影响[J]. 材料导报, 2019, 33(z1): 62-66.
[3] 丁晓飞, 范同祥. 石墨烯增强铜基复合材料的研究进展[J]. 材料导报, 2019, 33(z1): 67-73.
[4] 张谦. 不同铺层角含孔复合材料板拉伸性能数值模拟[J]. 材料导报, 2019, 33(z1): 145-148.
[5] 岳慧芳, 冯可芹, 庞华, 张瑞谦, 李垣明, 吕亮亮, 赵艳丽, 袁攀. 粉末冶金法烧结制备SiC/Zr耐事故复合材料的研究[J]. 材料导报, 2019, 33(z1): 321-325.
[6] 周春波, 张有智, 张岳, 王煊军. 聚乙烯基石墨烯复合多孔球形材料的制备及性能表征[J]. 材料导报, 2019, 33(z1): 453-456.
[7] 裴梓帆, 王雪, 唐寅涵, 段皓然, 崔升. 磁性气凝胶材料的应用研究进展[J]. 材料导报, 2019, 33(z1): 470-475.
[8] 罗继永, 张道海, 田琴, 魏柯, 周密, 杨胜都. 无机纳米粒子协同无卤阻燃聚丙烯的研究进展[J]. 材料导报, 2019, 33(z1): 499-504.
[9] 杨康, 赵为平, 赵立杰, 梁宇, 薛继佳, 梅莉. 固化湿度对复合材料层合板力学性能的影响与分析[J]. 材料导报, 2019, 33(z1): 223-224.
[10] 余江滔, 田力康, 王义超, 刘柯柯. 具有超高延性的再生微粉水泥基复合材料的力学性能[J]. 材料导报, 2019, 33(8): 1328-1334.
[11] 李茂源, 卢林, 戴珍, 洪义强, 陈为为, 张玉平, 乔英杰. 玻璃微珠和ZrB2改性石英酚醛复合材料的耐烧蚀性能[J]. 材料导报, 2019, 33(8): 1302-1306.
[12] 王应武, 左孝青, 冉松江, 孔德昊. TiB2含量及T6热处理对原位TiB2/ZL111复合材料显微组织和硬度的影响[J]. 材料导报, 2019, 33(8): 1371-1375.
[13] 韩银娜, 张小军, 李龙, 周德敬. 铝基层状复合材料界面金属间化合物的研究现状[J]. 材料导报, 2019, 33(7): 1198-1205.
[14] 朱佳佳, 黄斌, 李延伟, 陈权启, 李庆奎, 杨建文. 氧化亚锰的制备及储镁电化学性能[J]. 材料导报, 2019, 33(6): 923-926.
[15] 王鸣, 黄海旭, 齐鹏涛, 刘磊, 王学雷, 杨绍斌. 还原氧化石墨烯(RGO)/硅复合材料的制备及用作锂离子电池负极的电化学性能[J]. 材料导报, 2019, 33(6): 927-931.
[1] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6] XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg98.5Zn0.5Y1 Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7] ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed