Please wait a minute...
《材料导报》期刊社  2017, Vol. 31 Issue (2): 126-129    https://doi.org/10.11896/j.issn.1005-023X.2017.02.027
  材料研究 |
中钛型含钛高炉渣制微晶玻璃及其性能研究*
贺东风, 潘江涛, 曾凡博
北京科技大学冶金与生态工程学院, 北京 100083;
Preparation and Characterization of Glass-ceramics Based on Medium Titanium-bearing Blast Furnace Slag
HE Dongfeng, PAN Jiangtao, ZENG Fanbo
School of Metallurgical and Ecological Engineering, University of Science and Technology Beijing, Beijing 100083;
下载:  全 文 ( PDF ) ( 1439KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 以中钛型含钛高炉渣为主原料制备微晶玻璃,利用渣中的TiO2作晶核剂。采用差示扫描量热法(DSC)、X射线衍射(XRD)和扫描电子显微镜(SEM)等分析技术研究了含钛高炉渣用量的变化对基础玻璃晶化、微晶玻璃性能的影响。结果表明,渣中适量的TiO2对玻璃晶化有较好的促进作用。渣用量较低时制得的微晶玻璃的主晶相为硅灰石,但当渣用量超过70%时,主晶相发生变化,变为钙铝黄长石等长石类矿相。中钛型含钛高炉渣用量为63%左右时,制得的微晶玻璃晶相含量合适,性能最好。此时采用的热处理制度为:核化温度720 ℃,保温1 h,晶化温度945 ℃,保温2 h,制得的微晶玻璃抗弯强度为121.68 MPa,显微硬度为7.81 GPa。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
贺东风
潘江涛
曾凡博
关键词:  含钛高炉渣  微晶玻璃  晶核剂  力学性能  资源综合利用    
Abstract: Medium titanium-bearing blast furnace slag was used as the main material to manufacture glass-ceramic. TiO2 in this type of blast furnace slag serves as an effective constitute in terms of promoting the nucleation process. The effects of the mass fraction of blast furnace slag in the parent glass on the crystallization and properties of final products were studied by scanning calorimetry (DSC), X-ray diffraction (XRD), scanning electron microscopy (SEM) and etc. It is found that a medium-level of TiO2 in blast furnace slag could effectively initiate the crystallization within the parent glass. Low mass fraction of blast furnace slag would result in wollastonite as the major crystalline phases. In contrast, when the mass fraction of blast furnace slag exceeded 70%, the major phase would turn into gehlenite. Furthermore, when the mass fraction of blast furnace slag was 63%, the final glass-ceramic product with a desired crystallinity was characterized by excellent performance. The corresponding heat treatment systerm included a nucleating stage at 720 ℃ for 1 h and a crystal growth stage at 945 ℃ for 2 h. The resulting product possessed a bending strength of 121.68 MPa and a microhardness of 7.81 GPa.
Key words:  titanium-bearing blast furnace slag    glass-ceramics    nucleating agent    mechanical properties    resource comprehensive utilization
               出版日期:  2017-01-25      发布日期:  2018-05-02
ZTFLH:  TF09  
基金资助: *国家自然科学基金(51534001)
作者简介:  贺东风:男,1975年生,博士,副教授,主要研究方向为冶金渣综合利用 E-mail:hdfcn@163.com
引用本文:    
贺东风, 潘江涛, 曾凡博. 中钛型含钛高炉渣制微晶玻璃及其性能研究*[J]. 《材料导报》期刊社, 2017, 31(2): 126-129.
HE Dongfeng, PAN Jiangtao, ZENG Fanbo. Preparation and Characterization of Glass-ceramics Based on Medium Titanium-bearing Blast Furnace Slag. Materials Reports, 2017, 31(2): 126-129.
链接本文:  
http://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2017.02.027  或          http://www.mater-rep.com/CN/Y2017/V31/I2/126
1 Wu J P, Rawlings R D, Boccaccini A R, et al. A glass-ceramic derived from high TiO2-containing slag: Microstructural development and mechanical behavior[J]. J Am Ceram Soc,2006,89(8):2426.
2 Francis A A. Conversion of blast furnace slag into new glass-ceramic material[J]. J Eur Ceram Soc,2004,24(9):2819.
3 Barbieri L, et al. Design, obtainment and properties of glasses and glass-ceramics from coal fly ash[J]. Fuel,1999,78(2):271.
4 Khater G A. Influence of Cr2O3, LiF, CaF2 and TiO2 nucleants on the crystallization behavior and microstructure of glass-ceramics based on blast-furnace slag[J]. Ceram Int,2011,37(7):2193.
5 Guo Xingzhong, Yang Hui, Yang Guangyue, et al. Effect of composite nucleation agents on crystallization and properties of CaO-MgO-Al2O3-SiO2 glass ceramics[J]. J Chinese Ceram Soc,2013,41(4):480(in Chinese).
郭兴忠,杨辉,杨广跃,等.含复合晶核剂CaO-MgO-Al2O3-SiO2微晶玻璃析晶与性能[J].硅酸盐学报,2013,41(4):480.
6 Cioffi R, Pernice P, Aronne A, et al. Glass-ceramic from fly ash with added MgO and TiO2[J]. J Eur Ceram Soc,1994,14(6):517.
7 Öveçogˇlu M L. Microstructural characterization and physical properties of a slag-based glass-ceramic crystallized at 950 and 1100 ℃[J]. J Eur Ceram Soc,1998,18(2):161.
8 王俭,毛裕文.渣图集[M].北京:冶金工业出版社,1989:222.
9 Cheng Jinshu, Li Shujing, Yang Fei. Effect of Na2O to high-temperature viscosity and crystallization of LAS glass-ceramics[J]. J Wuhan University of Technology,2010,32(22):44(in Chinese).
程金树,李淑晶,杨飞.Na2O对LAS微晶玻璃高温粘度及析晶的影响[J].武汉理工大学学报,2010,32(22):44.
10 Shi Peiyang, Jiang Maofa. Liu Chengjun, et al. Effect of CaO on glass ceramics crystallization and properties of CaO-Al2O3-SiO2 system[J]. J Chinese Ceram Soc,2004,32(11):1389(in Chinese).
史培阳,姜茂发,刘承军,等.CaO对CaO-Al2O3-SiO2 系微晶玻璃析晶和性能的影响[J].硅酸盐学报,2004,32(11):1389.
[1] 刘印, 王昌, 于振涛, 盖晋阳, 曾德鹏. 医用镁合金的力学性能研究进展[J]. 材料导报, 2019, 33(z1): 288-292.
[2] 张长亮, 卢一平. 氮元素对Ti2ZrHfV0.5Mo0.2高熵合金组织及力学性能的影响[J]. 材料导报, 2019, 33(z1): 329-331.
[3] 晁代义, 徐仁根, 孙有政, 赵巍, 吕正风, 程仁策, 邵文柱. 850 ℃时效处理对2205双相不锈钢组织与力学性能的影响[J]. 材料导报, 2019, 33(z1): 369-372.
[4] 任秀秀, 朱一举, 赵省向, 韩仲熙, 姚李娜. 四种含能晶体微观力学性能与摩擦性能的关系[J]. 材料导报, 2019, 33(z1): 448-452.
[5] 薛晓武, 王新闻, 刘红波, 卿宁. 水性聚碳酸酯型聚氨酯的制备及性能[J]. 材料导报, 2019, 33(z1): 488-490.
[6] 杨康, 赵为平, 赵立杰, 梁宇, 薛继佳, 梅莉. 固化湿度对复合材料层合板力学性能的影响与分析[J]. 材料导报, 2019, 33(z1): 223-224.
[7] 平学龙, 符寒光, 孙淑婷. 激光熔覆制备硬质颗粒增强镍基合金复合涂层的研究进展[J]. 材料导报, 2019, 33(9): 1535-1540.
[8] 薛翠真, 申爱琴, 郭寅川. 基于孔结构参数的掺CWCPM混凝土抗压强度预测模型的建立[J]. 材料导报, 2019, 33(8): 1348-1353.
[9] 孙娅, 吴长军, 刘亚, 彭浩平, 苏旭平. 合金元素对CoCrFeNi基高熵合金相组成和力学性能影响的研究现状[J]. 材料导报, 2019, 33(7): 1169-1173.
[10] 李响, 毛萍莉, 王峰, 王志, 刘正, 周乐. 长周期有序堆垛相(LPSO)的研究现状及在镁合金中的作用[J]. 材料导报, 2019, 33(7): 1182-1189.
[11] 张雪峰, 崔泽波, 贾晓林, 刘芳. Cr2O3对尾矿氟金云母微晶玻璃电学性能和切削性能的影响[J]. 材料导报, 2019, 33(6): 970-974.
[12] 郭丽萍, 谌正凯, 陈波, 杨亚男. 生态型高延性水泥基复合材料的可适性设计理论与可靠性验证Ⅰ:可适性设计理论[J]. 材料导报, 2019, 33(5): 744-749.
[13] 赵立臣, 谢宇, 张喆, 王铁宝, 王新, 崔春翔. ZnO纳米棒/多孔锌泡沫的制备及其压缩和抗菌性能[J]. 材料导报, 2019, 33(4): 577-581.
[14] 何秀兰, 杜闫, 巩庆东, 郑威, 柳军旺. 凝胶-发泡法制备多孔Al2O3陶瓷及其力学性能[J]. 材料导报, 2019, 33(4): 607-610.
[15] 董天顺, 郑晓东, 李国禄, 王海斗, 周秀锴, 李亚龙. 大气等离子喷涂Fe基涂层及其氩弧重熔层的组织与力学性能[J]. 材料导报, 2019, 33(4): 678-683.
[1] Bingwei LUO,Dabo LIU,Fei LUO,Ye TIAN,Dongsheng CHEN,Haitao ZHOU. Research on the Two Typical Infrared Detection Materials Serving at Low Temperatures: a Review[J]. Materials Reports, 2018, 32(3): 398 -404 .
[2] Huimin PAN,Jun FU,Qingxin ZHAO. Sulfate Attack Resistance of Concrete Subjected to Disturbance in Hardening Stage[J]. Materials Reports, 2018, 32(2): 282 -287 .
[3] Siyuan ZHOU,Jianfeng JIN,Lu WANG,Jingyi CAO,Peijun YANG. Multiscale Simulation of Geometric Effect on Onset Plasticity of Nano-scale Asperities[J]. Materials Reports, 2018, 32(2): 316 -321 .
[4] Xu LI,Ziru WANG,Li YANG,Zhendong ZHANG,Youting ZHANG,Yifan DU. Synthesis and Performance of Magnetic Oil Absorption Material with Rice Chaff Support[J]. Materials Reports, 2018, 32(2): 219 -222 .
[5] Ninghui LIANG,Peng YANG,Xinrong LIU,Yang ZHONG,Zheqi GUO. A Study on Dynamic Compressive Mechanical Properties of Multi-size Polypropylene Fiber Concrete Under High Strain Rate[J]. Materials Reports, 2018, 32(2): 288 -294 .
[6] XU Zhichao, FENG Zhongxue, SHI Qingnan, YANG Yingxiang, WANG Xiaoqi, QI Huarong. Microstructure of the LPSO Phase in Mg98.5Zn0.5Y1 Alloy Prepared by Directional Solidification and Its Effect on Electromagnetic Shielding Performance[J]. Materials Reports, 2018, 32(6): 865 -869 .
[7] ZHOU Rui, LI Lulu, XIE Dong, ZHANG Jianguo, WU Mengli. A Determining Method of Constitutive Parameters for Metal Powder Compaction Based on Modified Drucker-Prager Cap Model[J]. Materials Reports, 2018, 32(6): 1020 -1025 .
[8] WANG Tong, BAO Yan. Advances on Functional Polyacrylate/Inorganic Nanocomposite Latex for Leather Finishing[J]. Materials Reports, 2017, 31(1): 64 -71 .
[9] HUANG Dajian, MA Zonghong, MA Chenyang, WANG Xinwei. Preparation and Properties of Gelatin/Chitosan Composite Films Enhanced by Chitin Nanofiber[J]. Materials Reports, 2017, 31(8): 21 -24 .
[10] YUAN Xinjian, LI Ci, WANG Haodong, LIANG Xuebo, ZENG Dingding, XIE Chaojie. Effects of Micro-alloying of Chromium and Vanadium on Microstructure and Mechanical Properties of High Carbon Steel[J]. Materials Reports, 2017, 31(8): 76 -81 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed