Please wait a minute...
《材料导报》期刊社  2017, Vol. 31 Issue (4): 25-29    https://doi.org/10.11896/j.issn.1005-023X.2017.04.007
  材料研究 |
麦秸/木材均质复合无机碎料板的制备及其性能*
潘亚鸽, 朱凌波, 唐钱, 黄清华, 李新功
中南林业科技大学材料科学与工程学院, 长沙 410004
Preparation and Properties of Inorganic Particleboard with a Uniform Mixture of
Wheat Straw and Wood
PAN Yage, ZHU Lingbo, TANG Qian, HUANG Qinghua, LI Xingong
School of Materials Science and Engineering, Central South University of Forestry and Technology, Changsha 410004
下载:  全 文 ( PDF ) ( 1620KB ) 
输出:  BibTeX | EndNote (RIS)      
摘要 以麦秸、木材和环保阻燃无机胶黏剂为主要原料,通过麦秸和木材碎料均匀混合的方式,采用热压工艺制备麦秸/木材均质复合无机碎料板,研究了麦秸与木材的配比、施胶量、热压时间和热压温度对板材性能的影响,并通过X射线衍射仪、扫描电镜分析了其对板材性能的影响机制。结果表明,随着麦秸与木材配比减小,板材静曲强度(MOR)、弹性模量(MOE)和内结合强度(IB)逐渐增大,2 h吸水厚度膨胀率(TS)逐渐减小,优选配比为m(麦秸)∶m(木材)=4∶6。随着施胶量的增大,板材的MOR、MOE先增大后减小,IB逐渐增大,TS逐渐减小。施胶量为63%时,板材的MOR、MOE分别达到最大值15.5 MPa、3 110 MPa,此时,IB、TS分别为0.47 MPa、5.5%。随着热压温度的升高和热压时间的延长,板材的MOR、MOE、IB逐渐增大,TS逐渐减小。热压温度和热压时间分别为100 ℃、30 min时,MOR、MOE、IB分别达到最大值(16.8 MPa、3 350 MPa、0.56 MPa),TS达到最小值(3.5%)。优化制板工艺为m(麦秸)∶m(木材)=4∶6,施胶量63%,热压时间30 min,热压温度100 ℃。
服务
把本文推荐给朋友
加入引用管理器
E-mail Alert
RSS
作者相关文章
潘亚鸽
朱凌波
唐钱
黄清华
李新功
关键词:  麦秸  木材  均质复合  无机碎料板  物理力学性能  优化工艺    
Abstract: With wheat straw, wood and environmentally friendly and flame retardant inorganic adhesive as major raw mate-rials, inorganic particleboard with a uniform mixture of wheat straw and wood was manufactured by hot-pressing technology.The effect of wheat straw-wood ratio, adhesive consumption, hot-pressing time and hot-pressing temperature on physical and mechanical properties of the board was studied, and influencing mechanism of them on the board′s properties was analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Results showed that modulus of rupture (MOR), modulus of elasticity (MOE) and internal bond strength (IB) of the board gradually increased while thickness swelling (TS) of that gradually decreased with declining wheat straw-wood ratio; optimal ratio was 4∶6. With increase of adhesive consumption, MOR and MOE firstly increased and then decreased, meanwhile, IB increased gradually and TS decreased gradually; MOR and MOE reached the maximum as 15.5 MPa and 3 110 MPa respectively when adhesive consumption was 63%, IB and TS was 0.47 MPa and 5.5% at this point. MOR, MOE and IB gradually increased while TS gradually decreased with increase of hot-pressing temperature and hot-pressing time; MOR, MOE and IB reached the maximum as 16.8 MPa, 3 350 MPa and 0.56 MPa, while the TS reached the minimum as 3.5% with hot-pressing temperature of 100 ℃ and hot-pressing time of 30 min. Optimal process was as follows: wheat straw-wood ratio of 4∶6, adhesive consumption of 63%, hot-pressing time of 30 min and hot-pressing temperature of 100 ℃.
Key words:  wheat straw    wood    uniform mixture    inorganic particleboard    physical and mechanical properties    optimal process
出版日期:  2017-02-25      发布日期:  2018-05-02
ZTFLH:  TB332  
基金资助: *湖南省科技厅科技计划项目(2015SK20422);湖南省教育厅科学研究项目(13C1147);中南林业科技大学引进高层次人才科研启动基金项目(104-0425)
通讯作者:  李新功:通讯作者,男,1970年生,博士,教授,研究方向为植物基复合材料 E-mail:lxgwood@163.com   
作者简介:  潘亚鸽:女,1990年生,硕士研究生,研究方向为生物质复合材料 E-mail:2293595737@qq.com
引用本文:    
潘亚鸽, 朱凌波, 唐钱, 黄清华, 李新功. 麦秸/木材均质复合无机碎料板的制备及其性能*[J]. 《材料导报》期刊社, 2017, 31(4): 25-29.
链接本文:  
https://www.mater-rep.com/CN/10.11896/j.issn.1005-023X.2017.04.007  或          https://www.mater-rep.com/CN/Y2017/V31/I4/25
1 Feng Wei, Zhang Liqun, Pang Zhongwei, et al. The economic and environmental analysis of crop residues burningand reutilization in China[J]. Chin Agricultural Sci Bull,2011,27(6):350(in Chinese).
冯伟,张利群,庞中伟,等.中国秸秆废弃焚烧与资源化利用的经济与环境分析[J].中国农学通报,2011,27(6):350.
2 Yu Wenji. Future development of bio-based composites from agricultural fibers in China[J].China Wood Ind,2006,20(2):41(in Chinese).
于文吉. 生物质资源农作物秸秆应用于人造板工业的可行性分析[J]. 木材工业,2006,20(2):41.
3 Müller C, Schwarz U, Thole V. On the utilization of agricultural residues in the wood-based panel industry [J]. Eur J Wood Wood Products,2012,70(5):587.
4 Nazerian M, Sadeghiipanah V. Cement-bonded particleboard with a mixture of wheat straw and poplar wood[J]. J Forestry Res,2013,24(2):381.
5 Yang Jianming. Study on processing technology of retardant straw plywood[D]. Changsha: Central South University of Forestry and Technology,2014(in Chinese).
杨建铭.阻燃秸秆人造板制造工艺研究[D].长沙:中南林业科技大学,2014.
6 Wu Yiqiang,Li Xingong,Zuo Yingfeng, et al. Research status on the utilization of forest and agricultural biomass in inorganic wood-based panel[J].J Forestry Eng,2016,1(1):8(in Chinese).
吴义强,李新功,左迎峰,等.农林剩余物无机人造板研究进展[J].林业工程学报,2016,1(1):8.
7 Xu Changwei, Wang Jianheng, Tian Yingliang, et al. Application of agricultural residues in inorganic building materials[J]. Agricultural Eng,2015,5(6):40(in Chinese).
徐长伟,王建恒,田英良,等. 农业剩余物在无机建筑材料中的应用[J]. 农业工程,2015,5(6):40.
8 Wang Xin, Zhou Dingguo. Influence of the chemical composition of agricultural straw on production process of straw-based panel[J]. China Forest Products Ind,2009,36(5):26(in Chinese).
王欣,周定国.农作物秸秆化学成分对人造板生产工艺的影响[J].林产工业,2009,36(5):26.
9 Zhang Xiyan. Straw characteristics and its influence on the perfor-mance of OSSB[D]. Xi’an: Northwest Agriculture Forestry University,2013(in Chinese).
张喜燕.麦秸原料的特性及其对定向结构麦秸板性能的影响[D].西安:西北农林科技大学,2013.
10 Cheng W L, Han G P, Fang D. Oriented structural boards from split wheat straw: Effects of straw length, panel density, and resin content[J]. BioResources,2013,8(3):4497.
11 Han Jingquan. Study on cement-bonded wheat straw composites[D]. Harbin:Northeast Forestry University,2009(in Chinese).
韩景泉.水泥基麦秸碎料复合材的研究[D].哈尔滨:东北林业大学,2009.
12 Yao Fei. Research on manufactory technique of rice-straw/wood-fiber composites[D]. Nanjing: Nanjing Forestry University,2004(in Chinese).
姚飞.稻草-木纤维复合材料制造工艺研究[D].南京:南京林业大学,2004.
13 Chen Mao, Li Xingong, Pan Yage, et al. Preparation and properties of inorganic poplar particleboard [J]. Acta Mater Compos Sin,2016,33(4):939(in Chinese).
陈茂,李新功,潘亚鸽,等.无机杨木刨花板制备及性能[J].复合材料学报,2016,33(4):939.
14 Li Ying, Yu hongfa, Dong Jinmei, et al. Reseach development on hydration product, phase transformation and water resistance eva-luation method of magnesium oxychloride cement[J]. J Chin Ceram Soc,2013,41(11):1465(in Chinese).
李颖,余红发,董金美,等.氯氧镁水泥的水化产物、相转变规律和抗水性评价方法的研究进展[J].硅酸盐学报,2013,41(11):1465.
15 Qin Linqing, Zhang Lianmeng, Huang Zhixiong. Analysis of activity and hydration product of magnesium oxide by X-ray diffractometry[J]. Analytical Instrumentation,2011,5(4):49(in Chinese).
秦麟卿,张联盟,黄志雄.X射线衍射法测定氧化镁的活性及其水化产物[J].分析仪器,2011,5(4):49.
16 Runcevski T, Dinnebier R E, Freyer D. Dehydration of the sorel cement phase 3Mg(OH)2·MgCl2·8H2O studied by in situ synchrotron X-ray powder diffraction and thermal analyses[J]. Zeitschrift Fur Anorganische Und Allgemeine Chemie,2014,640(1):100.
17 Fu Bin, Li Xingong, Pan Yage, et al. The preparation and properties of inorganic wheat straw particleboard [J]. J Funct Mater,2015,46(1):0112(in Chinese).
符彬,李新功,潘亚鸽,等.无机麦秸碎料板制备及性能[J].功能材料,2015,46(1):0112.
18 Qiao J Z, Wang A J, Li X G. Preparation and performance of wheat-straw composite board with inorganic adhesive[J]. BioResources,2016,11(1):819.
[1] 党奔, 陈志俊. 木基光热转换功能材料的应用研究进展[J]. 材料导报, 2025, 39(1): 24100143-13.
[2] 崔政, 李京超, 李建章, 高强. 木材胶黏剂仿生改性研究进展[J]. 材料导报, 2024, 38(8): 22110060-7.
[3] 王旭洁, 雒翠梅, 母军, 漆楚生. 热处理对木材多尺度结构及力学性能影响的研究现状[J]. 材料导报, 2024, 38(18): 23020251-8.
[4] 温佳璐, 刘文静, 张明辉. 木材吸湿特性的研究方法[J]. 材料导报, 2024, 38(18): 23030197-9.
[5] 王祺, 冯鑫浩, 刘新有. 古旧木材加固保护研究进展[J]. 材料导报, 2024, 38(1): 22070091-19.
[6] 范雨生, 王茹. 纳米二氧化硅对丁苯共聚物/硫铝酸盐水泥复合砂浆物理力学性能的影响[J]. 材料导报, 2023, 37(9): 21080193-7.
[7] 郭登康, 郭耐, 傅峰, 杨昇, 李改云, 储富祥. 有机物改性增强木材物理力学性能的研究进展[J]. 材料导报, 2023, 37(22): 22020187-11.
[8] 刘金明, 张一甫, 甘卫星, 莫海林. 糖基三聚氰胺甲醛树脂木材胶黏剂的研究进展[J]. 材料导报, 2023, 37(17): 21120170-7.
[9] 马彬, 衣兆林, 牛海华, 黄启钦. 高温下SiO2气凝胶改性地聚合物的物理力学性能研究[J]. 材料导报, 2023, 37(10): 21110251-6.
[10] 黄薇, 李红强, 官航, 冯海洋, 韦业, 古孜努尔·阿巴白克力, 赖学军, 曾幸荣. 天然木材的功能化及其应用进展[J]. 材料导报, 2022, 36(18): 20090093-7.
[11] 高玉磊, 徐康, 詹天翼, 江京辉, 蒋佳荔, 赵丽媛, 吕建雄. 热处理对木材吸湿吸水性的影响及其机理研究概述[J]. 材料导报, 2022, 36(15): 20100270-8.
[12] 邵亚丽, 王喜明. 木材形状记忆效应与机理的研究进展[J]. 材料导报, 2021, 35(7): 7190-7198.
[13] 孙振宇, 张源, 左迎峰, 吴义强, 王张恒, 吕建雄. 有机-无机复合改性速生木材研究现状与展望[J]. 材料导报, 2021, 35(5): 5181-5187.
[14] 夏容绮, 刘毅, 郭洪武. 透光性木材功能化改性研究进展[J]. 材料导报, 2021, 35(5): 5188-5194.
[15] 李萍, 张源, 吴义强, 袁光明, 李贤军, 左迎峰. 基于原位浸渍法的酚醛树脂改性杉木木材研究[J]. 材料导报, 2021, 35(22): 22193-22199.
[1] Huanchun WU, Fei XUE, Chengtao LI, Kewei FANG, Bin YANG, Xiping SONG. Fatigue Crack Initiation Behaviors of Nuclear Power Plant Main Pipe Stainless Steel in Water with High Temperature and High Pressure[J]. Materials Reports, 2018, 32(3): 373 -377 .
[2] Miaomiao ZHANG,Xuyan LIU,Wei QIAN. Research Development of Polypyrrole Electrode Materials in Supercapacitors[J]. Materials Reports, 2018, 32(3): 378 -383 .
[3] Congshuo ZHAO,Zhiguo XING,Haidou WANG,Guolu LI,Zhe LIU. Advances in Laser Cladding on the Surface of Iron Carbon Alloy Matrix[J]. Materials Reports, 2018, 32(3): 418 -426 .
[4] Huaibin DONG,Changqing LI,Xiahui ZOU. Research Progress of Orientation and Alignment of Carbon Nanotubes in Polymer Implemented by Applying Electric Field[J]. Materials Reports, 2018, 32(3): 427 -433 .
[5] Xiaoyu ZHANG,Min XU,Shengzhu CAO. Research Progress on Interfacial Modification of Diamond/Copper Composites with High Thermal Conductivity[J]. Materials Reports, 2018, 32(3): 443 -452 .
[6] Anmin LI,Junzuo SHI,Mingkuan XIE. Research Progress on Mechanical Properties of High Entropy Alloys[J]. Materials Reports, 2018, 32(3): 461 -466 .
[7] Qingqing DING,Qian YU,Jixue LI,Ze ZHANG. Research Progresses of Rhenium Effect in Nickel Based Superalloys[J]. Materials Reports, 2018, 32(1): 110 -115 .
[8] Yaxiong GUO,Qibin LIU,Xiaojuan SHANG,Peng XU,Fang ZHOU. Structure and Phase Transition in CoCrFeNi-M High-entropy Alloys Systems[J]. Materials Reports, 2018, 32(1): 122 -127 .
[9] Changsai LIU,Yujiang WANG,Zhongqi SHENG,Shicheng WEI,Yi LIANG,Yuebin LI,Bo WANG. State-of-arts and Perspectives of Crankshaft Repair and Remanufacture[J]. Materials Reports, 2018, 32(1): 141 -148 .
[10] Xia WANG,Liping AN,Xiaotao ZHANG,Ximing WANG. Progress in Application of Porous Materials in VOCs Adsorption During Wood Drying[J]. Materials Reports, 2018, 32(1): 93 -101 .
Viewed
Full text


Abstract

Cited

  Shared   
  Discussed